similar to: Can't get cable connection working on virtual router machine

Hi, I'm not sure what sort of diagram you mean, but I'll have a try. Does this help? It sounds like I need to do something to enable routing on what I've labelled "NIC3" on the diagram - can you please explain what I need to do? [image: Inline image 1] Regards, Phill On Tue, Sep 1, 2015 at 4:53 PM, Ajey Gore <ajeygore@gmail.com> wrote: > Can you please drop a

Hi Ajey, I thought I already was doing bridge mode. Below are the network interface definitions from the XML config file for the Sophos VM. (Note that it's actually the middle definition which is connected to the cable modem which is different to how I showed it in the earlier diagram). What I don't understand is that the interface type says "direct" in the XML even though in

does you cable modem give you automatically the IP address? if thats the case then you need to do bridge configuration between nic3 and macvtap dhcp ip and then you will be able to get dhcp attached IP to sophos vm - ajey On Tue, Sep 1, 2015 at 4:33 PM, Phill Edwards <philledwards@gmail.com> wrote: > Hi, I'm not sure what sort of diagram you mean, but I'll have a try. Does

Hi Phil, But you said you disabled firewalld which makes me wonder if you have the necessary forwarding rules active. Dan On 1 September 2015 at 13:48, Phill Edwards <philledwards@gmail.com> wrote: > Hi Ajey, I thought I already was doing bridge mode. Below are the network > interface definitions from the XML config file for the Sophos VM. (Note > that it's actually the

Can you please drop a rough diagram here? I think you are routing through this VM and must have shared the host interface. - ajey On Tue, Sep 1, 2015 at 7:39 AM, Phill Edwards <philledwards at gmail.com> wrote: > I'm pretty new to KVM and have a KVM CentOS 7.1 hypervisor running a few > VMs. I'm moving all my VMs from an ESXi host as I want to use KVM in > future. Most

Hello all, I''m using shorewall on a linux machine that has two interfaces, eth0 being connected on the internal network (10.10.10.0/24) and eth1 being connected to the external network. On eth0 the IP is statically configured to 10.10.10.254 and there is a dhcp server running for the machines in the private network. On eth1, the IP is dynamically assigned by my ISP modem that acts as

We are seeing lots of IMAP login attempts like this: dovecot[363]: imap-login: Disconnected (auth failed, 1 attempts in 6 secs): user=<xcentrex5fxnewx5fxyorkx5fxquotex5fxisx5fxreadyx2dxx2dx426453.eml>, method=PLAIN, rip=197.255.60.118, or dovecot[363]: imap-login: Disconnected (auth failed, 1 attempts in 6 secs): user=<xmatchingx5fxyourx5fxrecentx5fxvisitx5fxonx5fxx2dxx2dx121584.eml at

Laine wrote: > -----Original Message----- > From: sendmail [mailto:justsendmailnothingelse@gmail.com] On Behalf > Of Laine Stump > Sent: Monday, March 16, 2015 4:12 PM > To: libvirt-users@redhat.com > Cc: Lentes, Bernd > Subject: Re: [libvirt-users] still possible to use traditional bridge network > setup ? > > On 03/16/2015 10:08 AM, Lentes, Bernd wrote: > >

Hi-- Are folks familiar with: http://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2011-0997 http://www.isc.org/software/dhcp/advisories/cve-2011-0997 http://nakedsecurity.sophos.com/2011/04/07/flaw-in-iscs-dhclient-could-allow-remote-code-execution/ Checking http://www.freebsd.org/cgi/cvsweb.cgi/src/sbin/dhclient/dhclient.c, I don't see signs that it may have been updated. But, I also

Hello Andrew. On Fri, May 27, 2016 at 5:20 PM, Andrew Bartlett <abartlet at samba.org> wrote: > On Fri, 2016-05-27 at 12:18 -0300, Marcelo Terres wrote: >> Hello. >> >> Just one doubt: Samba4 already supports CLDAP requests? > > Yes, we support CLDAP. What made you have this doubt? > I'm using Sophos UTM and I'm trying to add the machine in Domain. I

Hello. I recently tried installing NetBSD-5 on xen-4.0.1-rc5, which resulted in no network (xennet0 can''t get IPs per dhclient and has no connectivity if set by hand). Tried it with netBSD-5.1-RC3-1 i386 PAE & amd64, netBSD-5.0 and even 4, all with the same result. On a older xen version (3.3.1) networking works fine, so I assume it''s a xen bug, and not a netBSD-kernel

Hi, i'm currently installing a SLES 12 64bit system. libvirt-client-1.2.5-13.3.x86_64 and libvirt-daemon-1.2.5-13.3.x86_64. Formerly I created my vm's (KVM) using a traditional bridge in my host systems, mostly SLES 11 SP3. But with SLES 12 I don't succeed. I can use the macvtap device in the host, but I like to be able to communicate between host and guest. Is the traditional bridge

Hi, kickstarting fails due to problems with host resolution, even though the network seems to be properly configured through DHCP. eno1 and eno2 are both attached to the network, but only eno1 gets an IP via DHCP. Still `curl` cannot resolve the mirror host and the kickstart host during dracut-initqueue: rdsosreport.txt ------------------------------------------------ [...] [ 14.780428]

Hello, I have the AR9285 wireless adaptor on an HP DV6-2128ca notebook. I can see it. it comes up in NetworkManager but never gets an IP. the router is a linksys using WPA/PSK security. Would/could someone please help me out trying to get this to work? Output of several commands follows: dmesg: ath: EEPROM regdomain: 0x69 ath: EEPROM indicates we should expect a direct regpair map ath:

On 03/16/2015 01:07 PM, Lentes, Bernd wrote: > Bernd wrote: > >> Laine wrote: >> >>> -----Original Message----- >>> From: sendmail [mailto:justsendmailnothingelse@gmail.com] On >> Behalf Of >>> Laine Stump >>> Sent: Monday, March 16, 2015 4:12 PM >>> To: libvirt-users@redhat.com >>> Cc: Lentes, Bernd >>>

During the build (via a serial console) we get input: ImExPS/2 Generic Explorer Mouse as /class/input/input1 running install... running /sbin/loader Sending request for IP information for eth0... Determining host name and domain... Sending request for IP information for eth0... Determining host name and domain... And there it hangs. On the 6.3 host: Feb 8 08:28:55 penfold dhcpd:

Hi list, Are there any problems with the if_re ? After upgrade RELENG_7 on my laptop NIC stopped to work:( uname -a: FreeBSD notebook.minsk.domain 7.2-PRERELEASE FreeBSD 7.2-PRERELEASE #3: Fri Apr 10 20:38:55 EEST 2009 root@notebook.minsk.domain:/usr/obj/usr/src/sys/tiger-asus-a6m i386 notebook# dhclient re0 DHCPDISCOVER on re0 to 255.255.255.255 port 67 interval 3 DHCPDISCOVER on re0 to

Hello Samba Team ! First at all. It's seems that my problem is NOT (or not only) a Samba Winbind problem. But I need to understand what's happen to send good reports to correct maintainers. What's I'm trying to achieve : ------------------------------------------ Gnome gdm introduced a great feature that suspend the system on logout. This help a lot reducing the electric

This is my system info: Debian Release: 10.5 APT prefers stable-updates APT policy: (500, 'stable-updates'), (500, 'stable') Architecture: amd64 (x86_64) Kernel: Linux 5.4.60-1-pve (SMP w/16 CPU cores) Kernel taint flags: TAINT_PROPRIETARY_MODULE, TAINT_OOT_MODULE Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8), LANGUAGE=en_US:en (charmap=UTF-8) Shell: /bin/sh

Dear I need create second bridge xenbr1 for separate traffic between my virtual machine , I following this step but show message that Link veth0 is missing, how I can create veth0 ? When I run script for create xenbr1 ./network-bridge netdev=eth1 bridge=xenbr1 start Shwo this message Link veth0 is missing. This may be because you have reached the limit of the number of interfaces that the