similar to: SNMPv3 fails when more than one UPS is configured in ups.conf

Hi Charles, Running upsdrvctl -D start on the host with all three configured to SNMPv3 kicks out 56 different "unhandled ASN 0x81 from ..." lines on all three but importantly they all start up and keep running. I'm starting to suspect the startup is taking so long that systemd is timing out and killing it. time -p reports real time of 133.27. I'm not a fan of systemd but

nut-2.6.5 Scientific Linux 6.3 APC AP9630 management card My basic question is, does nut's SNMPv3 implementation work? I have this in /etc/ups/ups.conf ...... [tfapc01] driver = snmp-ups port = tfapc01.testfest.ixorg.org mibs = apcc snmp_version = v3 secLevel = authPriv secName = tfsnmpprof1 authPassword = ralow6moHet7zoboP8 privPassword = tuseL8Pakaz9degim7 authProtocol=MD5

I have three APC SmartUPS 5000s. Two of them are AP9617 and one is AP9619. I have a RS-232 connections from my monitor host to all three. All three report status and give information. One of the two AP9617 - ups3-1 - does not shut down when FSD is sent. It did when I first set this system up a year or two ago but it's stopped doing so since then. Resetting the management interface does not

I've told systemd to wait up to 10 minutes for startup but it's still failing. Sometimes it fails with "timeout exceeded" and sometimes with the ASN error previously reported. I went back to running upsdrvctl -D to see if I could see anything. On the third run I saw messages about "startup timer elapsed" for ups2-1 and then it tried again to launch that one (killing

Hello, I've got a setup with NUT, where we've got two UPSes, ups1 and ups2. UPS1 supports our servers, while UPS2 supports our desktop boxes. We monitor both of them via USB on a box now called "upsmon". The interesting point comes here. We monitor both UPSes on the upsmon box, but if UPS2 fails, which supports our desktop boxes, NUT shouldn't initiate a shutdown in

On Nov 30, 2017, at 6:31 PM, Lee Damon <nomad at ee.washington.edu> wrote: > > SNMPv3 works fine when I have any one of the three configured in > ups.conf while the other two are configured with SNMPv1. It doesn't > matter which _one_ UPS is configured for SNMPv3 in ups.conf, they all > work individually (see below example). > > However, if I configure any two or

Hi, I've got two MGE Ellipse 1500 UPS connected via usb to an ubuntu jaunty system with nut and libupsclient1 2.4.1-2ubuntu4. As soon as I start the driver for the second one, they start fighting each other and I get no data. I found an older post to this list that said: If you want to monitor multiple UPSes through usbhid-ups, you *must* make sure that each one can be uniquely identified

Hi, I've got a question about managing two UPSes under NUT. I have two similar model APC usb-connected UPSes to work with, but don't know how to manage them simultaneously from under Windows. Long story short, my ups.conf looks like this: --- ups.conf --- [ups1] driver= usbhid-ups port= auto serial=AS1054340323 [ups2] driver= usbhid-ups port= auto serial=AS1026662626 ---

Hi, I didn't found an answer for my question in NUT documentation/FAQ or this mailing list archive so I?m posting it here. I want to start a timer only if both of my UPSes remain on battery. Not just one, both. My UPSes are: - ups1@host-a - ups2@host-b Is it possible to use something like this in upssched.conf? AT ONBATT ups1.* && ups2.* START-TIMER onbattwarn 180 Thanks,

Hello, We have two APC Back-UPS RS 1500 USB stuff, and i've got a bit of a problem with it and NUT. The usbdevs output: addr 2: Back-UPS RS 1500 FW:8.g8 .I USB FW:g8, American Power Conversion addr 3: Back-UPS RS 1500 FW:8.g8 .I USB FW:g8, American Power Conversion (UPS1 and UPS2) I've configured our NUT system to monitor the UPSes, and it went very fine till the time had arrived for a

I'm trying to get SNMPv3 management working for an APC AP9617 card. It is newly refurbed, running sumx v3.7.2 and aos v3.7.3. In the SNMPv3 user profiles section I have (I don't care about the password leaking, it's temporary): User Name: nut Authentication Passphrase: NutScan at Password43LongerWord Privacy Passphrase: NutScan at Password43LongerWord Authentication protocol:

On Mar 31, 2015, at 9:07 AM, Jason Gould <jgould at cddiagnostics.com> wrote: > I missed that snmp-ups set pollfreq to 30 by default. I?d hope that it would set deadtime to an appropriate value as well than, no? Is there a way to query what the settings are or what the defaults are? There is a TODO comment in snmp-ups that mentions doing something similar to usbhid-ups: just poll the

Hello!! I'm a sysadmin at La Laguna University in Spain. We are using NUT to manage our UPS with great success, but we miss a feature and we would like to send this patch to you. If you apply this patch running upsd -c info you'll get information about client connections in syslog. This is very simple and helpfull if you have hundreds of servers connected to the same upsd. Thank you for

I can't find a way to configure bcmxcp_usb to communicate with 2 UPS units. Maybe more simply, I can't find a way to tell the driver to only talk to one of the units on the bus. That is, I cannot find that the driver configuration file supports "serial =" or "bus = " or other such discriminators that other drivers do (usb_apc, etc.). So, I can't assign one Eaton

Hello guys, I was some years ago when I sent something to this list. NUT is a great tool but lacks SNMP management. It can access a device using SNMP but I found no way to read NUT values using SNMP. It would be very useful in order to integrate with network management software based on SNMP. As I did not find a solution, I wrote it myself. I wrote a MIB file and a SNMP agent for net-snmp

Hello guys, I was some years ago when I sent something to this list. NUT is a great tool but lacks SNMP management. It can access a device using SNMP but I found no way to read NUT values using SNMP. It would be very useful in order to integrate with network management software based on SNMP. As I did not find a solution, I wrote it myself. I wrote a MIB file and a SNMP agent for net-snmp

root at Monitor:/etc/nut# upsc ups1 Init SSL without certificate database battery.runtime: 133200.00 battery.runtime.elapsed: 0.00 device.mfr: CYBERPOWER device.model: PR2200LCDRT2U device.serial: 1 device.type: ups driver.name: snmp-ups driver.parameter.pollfreq: 1 driver.parameter.pollinterval: 2 driver.parameter.port: 192.168.1.7 driver.parameter.snmp_version: v1 driver.version:

Hi, my name is Sebasti?n from Spain I need help for that. I have 2 salicru ups I need monitor with a fedora 14 pc. Someone knows if i can configure ups.conf to monitor one or another ups? only make a upsc "ups" for take data. The upses are connected via usb and nut always read the first one connected. The upses are the same model. Thanks for all! Sebasti?n Le?n del Moral urticaries at

I'm trying to setup a server controlling 8 ups, 6 APC Smartups 1500 and two 1000. Because of the number of ups, i connected them using usb cables. I'm using Debian Etch AMD64 and nut 2.2.0 from testing (already tried 2.0 from stable, but had problems reading the ups serials and all the following problems of 2.2). This is my ups.conf: [ups2] driver = usbhid-ups port =

OpenBSD 5.6 nut-2.7.2 (bin package) Liebert IntelliSlot Unity Card IS-UNITY-DP ups.conf: ...... ? mibs = ietf ? snmp_version = v1 ...... The problem is that the card responds to other snmp (v1,2c,3) requests normally but not to the 1.3.6.1.2.1.33.1.1.1.0 (UPS-MIB.upsIdentManufacturer). # snmp-ups -a laes2ups -DDDDDDD Network UPS Tools - Generic SNMP UPS driver 0.72 (2.7.2) ?? 0.000000???? debug