similar to: Problem installing NUT on 16.04

Thanks again for your patience. I'm still learning how to deal with systemctl myself (and starting from, I'm sure, a much lower level of understanding), so if I've neglected to restart or start something, please let me know. I made the change to /etc/nut/upsd.conf. I restarted upsdrvctl, which reported back: Network UPS Tools - UPS driver controller 2.7.4 Network UPS Tools - Generic

Charles, It starts out good, then goes into a Connection timed out loop. If I can provide any information to fix a driver I'll do my best. Here's the output: # /usr/local/ups/bin/usbhid-ups -DD -a eaton Network UPS Tools - Generic HID driver 0.41 (2.7.4) USB communication driver 0.33 0.000000 debug level is '2' 0.002550 upsdrv_initups... 0.288229 Checking device

I recently purchased a CyberPower CP1500PFCLCD UPS as a replacement UPS for a headless server running Slackware 14.1 with the 3.10.7 kernel. I then downloaded the NUT 2.7.1 tarball on the server and following the directions installed the software. The installation went well and the UPS will shutdown the server using the forced down test and then it powers back up as it should. The

I've searched the listserv archive, to no avail, so I hope I'm not duplicating a previous problem. I am anxious to get this working, so I'm open to uninstalling what I have and starting over. One note which may not be meaningful is that this UPS pre-dates the Raspberry Pi I've got connected to it, and I used to use it with the CyberPower software, which requires logging in with a

My UPS is connected to a Raspberry Pi by USB. After a few hours of working, the service fails. Looking at kernel messages I noticed that the device is repeatedly disconnecting and reconnecting. I have tried using a different USB port and using a brand new USB cable. I have not had success by changing config parameters like pollfreq/pollinterval/etc. What is causing the UPS to keep disconnecting?

Hello, I have been using NUT for a short period of time and have some questions regarding the UPS reboot signal that I can't figure out. Have tried some googling and reading the DOCs but I am struggling to understand how some variables / things are supposed to work, so would appreciate any help with any of the following questions. I am running NUT on standalone mode on a linux machine

Hi! Info OS: TinyCore Linux 4.5.6 NUT version: 2.6.4 NUT innstallation method: source tarball Device name: Eaton Ellipse ups eco 1600 usb din (EL1600USBDIN) /usr/local/ups/etc/ups.conf file: [eaton] driver = usbhid-ups port = auto When I run: root at Dalen:/usr/local/ups/bin/upsdrvctl start eaton I get this error message: Network UPS Tools - UPS driver controller 2.6.4

To all, I attempted to configure the UPS tools for the Tripp-Lite SmartOnline 1500VA 2U rackmount UPS. I followed the instructions from the 'upsdrvctl start' output and posted the diagnostic information below. Is my UPS using an unknown product ID as reported? From the mailing list archive, I have found another posting for the same UPS with device model '09AE/4003', whereas

Thanks for the reply. However these two FAQ are unfortunately not describing the situation. - The first issue is that NUT switches off the UPS upon reboot on low battery (not that it dies because of low battery) - The second issue is that the UPS does not recognise being online again (not that the PC does not restart) Sent from my iPhone > On 11 Jun 2019, at 02:03, Charles Lepple <clepple

On 10/01/2015 00:45, Charles Lepple wrote: > On Jan 8, 2015, at 11:43 PM, Graham Menhennitt > <graham at menhennitt.com.au <mailto:graham at menhennitt.com.au>> wrote: > >> Hello Nutters, >> >> I'm running nut 2.7.2 on FreeBSD 10-stable (via the FreeBSD port) >> with an APC Back-UPS CS 350 connected via USB. I get persistent >> (every few

Hi, This might be a simple thing to fix, but I can?t figure it out. We replaced the battery for the first time in our Eaton 5PX a couple of weeks ago, but we haven?t been able to clear the ?ups.alarm: replace battery!? status. Details of our installation are: OS: Debian 6 NUT version: 2.7.4 Installation method: from source tarball UPS device: Eaton 5PX2000IRT, 240V, 1800W, 2000VA, bought in

Hello. Not listed as supported, so here is some info, [root at vhost ~]# /usr/sbin/usbhid-ups -DD -a powercom Network UPS Tools - Generic HID driver 0.38 (2.7.2) USB communication driver 0.32 0.000000 debug level is '2' 0.001318 upsdrv_initups... 0.074753 Checking device (0529/0001) (003/002) 0.074835 Failed to open device, skipping. (Permission denied)

Hello, I am hoping someone can point me in the right direction. I am setting up a new UPS, most things seem to be working except the UPS turns off immediately during a test shutdown using///"//upsmon -c fsd".//No delay before the UPS turns itself off leaving no time for the server to shutdown properly. I have attempted to set the delay higher using "upsrw -s

Hi there, OS: (L)ubuntu 12.04 precise LTS Nut: 2.6.3-1ubuntu1.1 Installation Method: Package (apt-get install nut) Hardware: HP R1500 G3 INT Hardware-Specs: http://h18004.www1.hp.com/products/quickspecs/14059_div/14059_div.pdf Problem: I tried to set up nut with our new arrived HP R1500 G3 UPS but there is a failure with the usb connection. After trying "/lib/nut/usbhid-ups -DD -a

On Jun 10, 2019, at 2:32 PM, Marc Finns wrote: > > Hello, I read all FAQ and other sources but I could not find this situation, so I thought of asking the experts. > I successfully configured a Raspberry NUT server to control my UPS that powers several devices (NUC with ESXI VMs, Synology NAS etc). > All works well in principle, but I have the following behaviours that I could not

I have a Tripp-Lite BCPERS450, connected to a system running Ubuntu 16.04.3 LTS and NUT 2.7.2-4ubuntu1.2. I had to make my own /lib/systemd/system-shutdown/nutshutdown, but now everything is working except for powering on and off the UPS. Regardless of the settings of offdelay and ondelay in upsconf, and regardless of whether the AC power is on, when I say "upsdrvctl shutdown" the UPS

Thanks Charles, On Saturday 05 Apr 2014 12:53:06 Charles Lepple wrote: > On Apr 5, 2014, at 7:18 AM, Mick wrote: > > $ upsrw -s "ups.delay.shutdown"="30" iDowell at localhost > > Username (suzy): admin > > Password: > > OK > > This command is sending the value to the UPS (via the usbhid-ups driver). > > > $ upsc iDowell at localhost

I've just set up a CyberPower Value 2200E-GP on a system running Lucid AMD64, with the current NUT package via apt-get, and it seems to be working fine for me with the usbhid-ups driver, so I guess it can go in the HCL? I'm using the system to host several virtual servers under KVM, and to make things simple I set it up to hibernate rather than shutdown, that way all the guest OS

Hello all, About a month ago Peter and Charles were kind enough to try to help me with getting a Tripp Lite USB UPS to work with NUT. I reported quite a bit of initial success, and then other things here fell apart. Between work, fence building and a week-long out of town business trip, I have had to drop this from my list of things to do lately. I am back at it, and I believe I will have

Hello, I've recently bought Ippon Smart Winner 3000 New (note the "New" in the model name) and I can't make NUT to work with it. Linux gateway 3.17.8-gentoo-r1 #1 SMP Mon Feb 16 13:46:11 MSK 2015 x86_64 Intel(R) Celeron(R) CPU 1037U @ 1.80GHz GenuineIntel GNU/Linux Network UPS Tools 2.7.2 1) USB connection partially works using usbhid-ups driver, the problem is that I