similar to: cannot get APC ups status via usb cable from RaspberryPi

Hi All, I get very strange UPS problem from RspberryPI mode B (both version 2 and 3). Here is our environment: OS: Raspbian 8.0, Ubuntu 16.04 and Ubuntu 14.04 Platform: RaspberryPi Mode B version 2 and version 3 NUT: tested version 2.6.3, 2.7.1 and 2.7.2 (from

On May 31, 2016, at 1:11 AM, Tomas Tang <myhnet at gmail.com> wrote: > > Hi All, > > > > I get very strange UPS problem from RspberryPI mode B (both version 2 and 3). > > > > Here is our environment: > > > > OS: Raspbian 8.0, Ubuntu 16.04 and Ubuntu 14.04 > >

Hi All, I get very strange UPS problem from RspberryPI mode B (both version 2 and 3). Here is our environment: OS: Raspbian 8.0, Ubuntu 16.04 and Ubuntu 14.04 Platform: RaspberryPi Mode B version 2 and version 3 NUT: tested version 2.6.3, 2.7.1 and 2.7.2 (from ports.ubuntu.com) UPS: APC Smart-UPS 3000 RM and APC Smart-UPS 1500 RM Cable:

Sorry, I forgot this: torsten at raspberrypi:/ $ sudo /lib/nut/usbhid-ups -a UPS -x vendorid=051d -DD Network UPS Tools - Generic HID driver 0.38 (2.7.2) USB communication driver 0.32 0.000000 debug level is '2' 0.004718 upsdrv_initups... 0.007534 Checking device (051D/0002) (001/004) 0.008910 - VendorID: 051d 0.010030 - ProductID: 0002 0.011196

Hi there, Seeing an odd behaviour when running upsmon -c fsd to test my Raspberry Pi (running Jesse Lite) setup as a upsmon master, attached via USB to an APC Back-UPS XS1300. The Raspberry Pi is plugged into the Master outlet on the APC. The UPS clicks onto battery (and the fan spins up) for a few minutes, then resets, then repeats again, while finally remaining on AC power afterwards. The

Dear list, since some days I own an APC Back-UPS BX1400U. Now I try to connect my Raspberry Pi to it using NUT, but ... ;) The UPS is connected via an USB-cable, and "lsusb" shows an APC device. NUT is installed via "sudo apt-get install nut". My goal: a Synology DiskStation DS1515+ should "read" UPS-data provided from the Raspberry an shut-down itselt at 30%

On Feb 16, 2016, at 12:57 AM, T. Ermlich <pelegrine at gmail.com> wrote: > > Sorry for the email only send to you, Charles! > Here's the one for the list. I realize it is no longer a common list configuration. Feel free to use "Reply All" in Gmail - I won't get two copies. > torsten at raspberrypi ~ $ uname -a > Linux raspberrypi 4.1.13-v7+ #826 SMP

Sorry for the email only send to you, Charles! Here's the one for the list. torsten at raspberrypi ~ $ uname -a Linux raspberrypi 4.1.13-v7+ #826 SMP PREEMPT Fri Nov 13 20:19:03 GMT 2015 armv7l GNU/Linux torsten at raspberrypi ~ $ Cheers, Torsten Charles Lepple <clepple at gmail.com> schrieb am 15.02.2016 21:46: > On Feb 15, 2016, at 12:55 PM, T. Ermlich <pelegrine at

On Feb 15, 2016, at 12:55 PM, T. Ermlich <pelegrine at gmail.com> wrote: > > torsten at raspberrypi:/ $ sudo /lib/nut/usbhid-ups -a UPS -x vendorid=051d -DD > Network UPS Tools - Generic HID driver 0.38 (2.7.2) If the driver is crashing, you might be affected by this bug: https://github.com/networkupstools/nut/issues/258 https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=812604

On Sep 11, 2014, at 9:48 PM, Stan Gammons <sg063015 at gmail.com> wrote: > I have an APC USB UPS that was working on OpenBSD 5.5 with NUT 2.7.1 When I installed the latest 5.6 snapshot with NUT 2.7.2 the UPS no longer sends status messages when it loses line power. I asked over on the OpenBSD ports list and so far haven't had any luck getting this to work again. I disabled upd at

Dear NUT users/developers, I'm having trouble while trying to configure the UPS APC BZ2200BI-BR[1] in NUT, which despite having a USB cable it apparently communicates using the serial protocol. The relevant output of 'lsusb' is: Bus 002 Device 004: ID 051d:c812 American Power Conversion The device is registered as /dev/ttyACM0 and uses the kernel module 'cdc_acm' (USB

On 09/11/14 21:43, Charles Lepple wrote: > On Sep 11, 2014, at 9:48 PM, Stan Gammons <sg063015 at gmail.com> wrote: > >> I have an APC USB UPS that was working on OpenBSD 5.5 with NUT 2.7.1 When I installed the latest 5.6 snapshot with NUT 2.7.2 the UPS no longer sends status messages when it loses line power. I asked over on the OpenBSD ports list and so far haven't had

Hi everyone, I apologize if this has been covered before, but I didn?t see a way to search the mailing list archives. I?ve attached an APC ES-725 to my SuSE 9.2 box using the supplied USB cable. Looking through dmesg, I see that the OS recognizes the UPS. The problem I?ve got is mapping the UPS to a specific device within the OS so I can point NUT to it. It looks like the UPS is somewhere

hi, any one had luck using raspberrypi as mp3 source by configuring darkice or liquidsoap... if you are succeed or have an idea about it, please share... Thank You -Ashwin. +91-9959166266 -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.xiph.org/pipermail/icecast/attachments/20130718/6efa6500/attachment.htm

I'm trying to use a rackmount Smart-UPS from APC with the USB connector, and I'm running into some issues. They seem to stem from the fact that the Report Descriptor is much larger than any other UPS I've seen (61939 bytes). Here is the quick fix that I put in libusb.c after getting the HID descriptor, and before getting the Report descriptor, which seems to work okay:

Hello! I have installed the nut package from the OpenBSD 4.4 packages tree, nut-2.2.1p0 I have a new APC Smart-UPS 750 which I plan to connect via USB. When I try to start the usbhid-ups i get debug level is '2' upsdrv_initups... No appropriate HID device found No matching HID UPS found for almost anything i try. OpenBSD detects my UPS and assigns it to a device and it can be seen

Hi all, just installed the nut package from apt on Ubuntu. Here's what I got. Network UPS Tools - UPS driver controller 2.4.3 Network UPS Tools - Generic HID driver 0.34 (2.4.3) USB communication driver 0.31 This APC device (051d:0003) is not (or perhaps not yet) supported by usbhid-ups. Please make sure you have an up-to-date version of NUT. If this does not fix the problem, try running the

Hi there... nut 2.4.3 kicks an error at me when I try to talk to my UPS. machine is linux 2.4.21-32.ELsmp with libusb-0.1.8-3 package update. # /usr/local/ups/bin/upsdrvctl start Network UPS Tools - UPS driver controller 2.4.3 Network UPS Tools - Generic HID driver 0.34 (2.4.3) USB communication driver 0.31 Using subdriver: APC HID 0.95 libusb_get_interrupt: error submitting URB: Invalid

Hi all, I just got myself 2 APC Back-UPS CS 350 I downloaded the stable nut tar.gz installed it. This is not the first time i install and configure nut so i used the same configuration as on my other server as i always did. Then i made the 2 required modification. I changed these 2 thing: driver = apcsmart port = /dev/hiddev0 # ls -al /dev/hiddev0 crw------- 1 nut nut 180, 96

I have an APC USB UPS that was working on OpenBSD 5.5 with NUT 2.7.1 When I installed the latest 5.6 snapshot with NUT 2.7.2 the UPS no longer sends status messages when it loses line power. I asked over on the OpenBSD ports list and so far haven't had any luck getting this to work again. I disabled upd at boot as was suggested and that didn't change anything except stopping the