similar to: [HCL] Lyonn ULT-2000 MKR supported by

[Please keep the list CC'd - thanks!] > On Jun 3, 2016, at 11:58 AM, Marcos Martinez <marcosdmm at gmail.com> wrote: > > But I have to use my ups MIB file?? > Megatec gives a MIB file from his webpage, I think is NetAgent mini MIB. > I have to use that?? I am not familiar with all of the MIBs, but the NUT driver incorporates information from the supported MIBs - it

Lyonn CTB-1200 root at frambuesa:~# upsc lyonn at localhost battery.voltage: 27.20 battery.voltage.nominal: 24.0 beeper.status: enabled device.type: ups driver.name: blazer_usb driver.parameter.pollinterval: 2 driver.parameter.port: auto driver.version: 2.4.3 driver.version.internal: 0.03 input.current.nominal: 5.0 input.frequency: 49.9 input.frequency.nominal: 50 input.voltage: 213.3

Hi, anyone has configured NUT with an UPS Lyonn 2000-ULT KRM??? It isn't in the hardware compatibility list. Thanks -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.alioth.debian.org/pipermail/nut-upsuser/attachments/20160523/e29cbeb0/attachment.html>

Dear list, I''ve just tried to compile R 2.12.0 from source as I think I found an error in a C function that I would like to fix and check before I go ahead with posting the presumed error. I''ve got the R Toolset 2.12 installed and configured correctly and followed the Admin manual closely (including the entire bitmap stuff; exact same versions as in the manual). Also, all

I noticed that if I specify the location of TMPDIR in .bashrc as follows on a Linux 64 bit system: export TMPDIR=/store/home/ayee/.tmp I get the following error message when installing R make[3]: Entering directory `/home/ayee/R-patched/src/library/base' building package 'base' make[4]: Entering directory `/home/ayee/R-patched/src/library/base' /bin/sh: line 8:

Hi, I can't seem to install R from source. I've downloaded the latest Rtools211.exe from http://www.murdoch-sutherland.com/Rtools/ & done a full installation of that and Inno Setup. I have set R_HOME as C:\R (and also tried using C:\R\R-2.11.1) After successfully running 'tar xf R-2.11.1.tar.gz' the modifications I have made and saved as MkRules.local are: BUILD_HTML =

I have one of those new little NUC's and installed Centos 7.1 on it. lspci shows 00:00.0 Host bridge: Intel Corporation Haswell-ULT DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Haswell-ULT Integrated Graphics Controller (rev 09) 00:03.0 Audio device: Intel Corporation Haswell-ULT HD Audio Controller (rev 09) 00:14.0 USB controller: Intel Corporation 8 Series

On Thu, 11 Jan 2024 09:30:55 +1300 Simon Urbanek <simon.urbanek at R-project.org> wrote: > That said, WHICH is a mess - it may make sense to switch to the > command -v built-in which is part of POSIX (where available - which > is almost everywhere today) which would not require an external tool This is a bit tricky to implement. I've prepared the patch at the end of this

Hello list. I'm trying to rebuild the 2.6.9.67.0.20.EL kernel, but it fails even without modifications. How did I try it? Created a (non-root) build environment (not a mock ) Installed the kernel.scr.rpm and did a rpmbuild -ba --target=`uname -m` kernel-2.6.spec 2> prep-err.log | tee prep-out.log The build failed at the end: Processing files: kernel-xenU-devel-2.6.9-67.0.20.EL Checking