similar to: Pass CallerId/Privacy info from A Leg to B Leg

Hello all, I'm setting up a couple of test boxes and I'm running into a problem. What I need help with is determining whether I'm going something wrong or if I need to post a bug report. I have two asterisk 13.0-beta 3 machines set up with extensions connected to each as such: 3700 ----> AST-A <------> AST-B <---- 3800 & 3801 When I place a call from 3800 to

Hi, Is it working for anyone? I have tried with trustrpid=yes sendrpid=yes/pai but can not get it working, Asterisk cli shows prevented message like this. Connected line update to SIP/1231-00000200 prevented Regards, Zohair Raza -------------- next part -------------- An HTML attachment was scrubbed... URL:

Not sure why, but Vitelity changed the settings to IP based authentication on me. Here's the new sip.conf settings they sent me. type=friend dtmfmode=auto host=64.2.142.93 allow=all nat=yes canreinvite=no trustrpid=yes sendrpid=yes When I use these settings to originate calls using the sip.conf they sent me, everything works. Action: Originate ActionID: S8 Channel:

Hello, using Asterisk 1.8.12.2 case : I call with my cellphone to our public telephone number Our receptionist answers the incoming call and does an attended transfer to my colleague ( A ) Colleague answers and the receptionist tells him that I am on the other side. Receptionist transfers the call and I am connected to my colleague ( B ) My question is about the CallerID that the

On Mon, Dec 15, 2014 at 7:34 PM, Dan Cropp <dan at amtelco.com> wrote: > > I am not sure if I entered the correct settings for the transport > information. > > For the local_net, I entered my local ip address, but no mask. I will > check with the network admin so he can verify the settings I entered. > > > You need the network and mask. For example if the ip

I have many endpoints and each endpoint has some parameter in common so i wonder is there any way to config one for all endpoints? Like in my example I have two endpoints and I repeat the same thing, [100] type=endpoint aors=100 auth=100-auth allow=ulaw,alaw,gsm,g726 context=from-internal callerid=device <100> dtmf_mode=rfc4733 use_avpf=no ice_support=no

Hello Everyone, Our switch is sending P-Asserted info to asterisk however the information is getting removed when asterisk forks the call. Is it possible to have asterisk retain the P-Asserted on the leg. This is quite important for valid functionality of our network. Tried setting `sendrpid = yes` and still same problem. We really don't want to have to `SipAddHeader` as it is already being

Asterisk 13.8 Is CALLERID(all) supposed to wok for pjsip? When I do this: exten => 1234,Set(CALLERID(all)="Jon Doe" <+123456789>) same => n,Dial(PJSIP/phone123, 30) I expect the callerid to be as set, but is always seems to be "phone123", the name of the endpoint. Andrew -------------- next part -------------- An HTML attachment was scrubbed... URL:

I've seen this happen three times in the wild now.  I've been trying to isolate the source of the issue, but so far it seems like there's not enough debug output to know why this occurs. Long story short: - Start Asterisk - PJSIP Handles receiving INVITE from ITSP via WAN (Asterisk is behind NAT).  SIP is handled correctly, Asterisk responds OK with RTP media address of

Hello, I have Asterisk 1.6.2.9-2, the directive "sendrpid" does not work! I placed this in my peer: (sip.conf) sendrpid=yes trustrpid=yes or sendrpid=yes trustrpid=no (and restarted Asterisk) and the line "Remote-Party-ID" does not appear in my sip debug! Please help me, Mickael. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, I've run into a minor snag trying to pass on CALLERID presence from one Asterisk to another via SIP (both running 13.16.0) I have a PRI coming in PBX_A and PBX_A is connected to PBX_B via SIP. PBX_A gets PRI calls on a 4 port Digium card, and each call naturally has its own callerid values and presence. I pass on those calls to PBX_B via SI, and I'm trying to pass on this

On 06/05/2017 at 11:30 AM, Joshua Colp wrote: > On Sun, Jun 4, 2017, at 10:40 AM, Michael Maier wrote: >> On 06/04/2017 at 01:41 PM Telium Technical Support wrote: >>> Just a guess (without knowing about your network), but are the two ends >>> points on public networks and visible to one another? If not the reinvite >>> may be passing an internal (nat'ed)

On Mon, Dec 15, 2014 at 9:48 PM, Dan Cropp <dan at amtelco.com> wrote: > > Thanks George. > > I will correct my local_net in the morning. > > Vitelity chan_sip settings I have working, do not have a fromuser. > sip.conf settings... > > I think you can actually specify anything, it just has to be populated with something other than a sub-account username. >

Gentlemen, I have 3 faxes attached to an Asterisk. Fax - SPA2102 - Asterisk. 0851711201 and 0851711290 is on our WAN, no NAT. 0197673581 is outside our WAN and needs to be NAT'ed. Sending a fax from 0851711201 to 0851711290, no problem, switches to T38 and fax goes through. Sending a from 0197673581 to 0851711201, no problem as long as i dont enable T38 on 0197673581. But, if i enable T38

how if I use the auto generate once from freepbx ? On Tue, Sep 22, 2015 at 10:12 PM, Ishfaq Malik <ish at pack-net.co.uk> wrote: > > > On 22 September 2015 at 16:04, Thyda ENG <engthyda at gmail.com> wrote: > >> I have many endpoints and each endpoint has some parameter in common so i >> wonder is there any way to config one for all endpoints? Like in my

Hi everyone, I am trying to figure out the behavior of trustrpid Basically its not behaving the way I expected it to or maybe I am missing a configuration option or something else. When a call from a phone is sent to the * box it has the following sip headers: From: "From Phone" <sip:1001 at 10.0.0.29>;tag=4bf4bb4e11e92476. Remote-Party-ID: "Cloutier"

Hi, I've two yocto questions about the syntax of dialplan: 1. What's the "official" notation of each line: "=>" or "=" ? In the wiki of Asterisk, I see very often "=>", however, what's the reason for both syntaxes authorized ? Historical ? 2. To write info in logs/console, you have two commands: NoOp and Verbose. Verbose seems to be

On 1 July 2016 at 17:41, Joshua Colp <jcolp at digium.com> wrote: > > >> exten => 1234,Set(CALLERID(all)="Jon Doe" <+123456789>) >> same => n,Dial(PJSIP/phone123, 30) >> > > Your exten line has no priority, is that how it is in your dialplan? > Actually no, I stole that line from an earlier email to this list. Mine has a priority.

We have an inbound PRI connected to our Cisco 3825 router which is then passing the calls to Asterisk as SIP calls. We're getting the CallerID number but not the CallerID name. We are seeing the name in the RPID field with a SIP trace on the Asterisk box but don't understand why it's not registering as the CallerID name. Here is a link to pastebin with the Sip trace. In it you

Hi List, Another dumb conversion question (I hope). I installed 10.0 and copied my 1.4 configuration files over. With a few tweaks everything works great except for 1 feature that I specifically went to 10.0 for. When I do an attended transfer, I still get the receptionists caller ID on the transferred phone instead of the incoming callerID. My assumption is that there is some