similar to: Xorcom T1 to PRI

Hello, My first attempt to get dahdi running on 1.4.28... with a Rhino 8 port modular card and a single FXS module. Got the Rhino card installed and the machine sees it: root at pbx:/etc/dahdi# dmesg | grep rcbfx [ 71.985309] rcbfx 0000:04:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 71.985440] rcbfx 1: Rhino PCI BAR0 50100000 IOMem mapped at ffffc90008d7c000 [ 71.985504]

Hi, On a Asterisk 1.8.12 system working OK for months (>100k calls proceed), users are complaining for bad audio. My setup is: PSTN <--E1/PRI ---> Asterisk <--- E1/PRI---> Siemens HiPath <---E1/PRI ---> PSTN asterisk -rx "dahdi show version" DAHDI Version: SVN-trunk-r10414 Echo Canceller: HWEC asterisk -rx "pri show version" libpri version: 1.4.12 A

Asterisk 11.1 We have a situation where one of our incomings POTS lines will not answer. There are 2 lines configured by the Telco as a rollover group (rings the line that is not busy) and they feed into a Digium AEX410 on the server. The most recent time this happened, I did a /etc/init.d/dahdi status and saw this: ### Span 4: WCTDM/1 "Wildcard AEX410" *53 FXO FXSKS

Hello Mailinglist, we have a Xorcom Astribank which is installed at our client and working since 10/2008. Suddenly last week there where odd behaviors, no calls going through (it is used to route calls to GSM Gateways). Upon testing (reinitialization of the complete gear) it turned out that one call get's through and then nothing more. I have nothing in the logs, indicating that Asterisk

Hey Guys! Please help me to find out issue. I have two PRI ## Span 1: WPT1/0 "wanpipe1 card 0" span=1,1,0,esf,b8zs bchan=1-23 hardhdlc=24 echocanceller=mg2,1-23 ## Span 2: WPT1/1 "wanpipe2 card 1" span=2,2,0,esf,b8zs bchan=25-47 hardhdlc=48 echocanceller=mg2,25-47 Sometime my calls got through but some time i am getting pri cause 44 sebpbx1*CLI> == Using SIP RTP

hi folks. recently some of our customers complained about bad voice quality on the phone system. i looked at the logs and found a lot of these: [2012-11-03 08:26:38] NOTICE[11305] chan_dahdi.c: PRI got event: HDLC Abort (6) on D-channel of span 1 [2012-11-03 08:26:45] NOTICE[11305] chan_dahdi.c: PRI got event: HDLC Abort (6) on D-channel of span 1 [2012-11-03 08:26:54] NOTICE[11305]

I installed 1 MDS , 2 OSS/OST and 2 Lustre Client. My MDS shows: [code] [root at MDS ~]# lctl list_nids 10.94.214.185 at tcp [root at MDS ~]# [/code] On Lustre Client1: [code] [root at lustreclient1 lustre]# lfs df -h UUID bytes Used Available Use% Mounted on lustre-MDT0000_UUID 4.5G 274.3M 3.9G 6% /mnt/lustre[MDT:0] lustre-OST0000_UUID

lspci | grep Digium 03:05.0 Ethernet controller: Digium, Inc. Wildcard TE122 single-span T1/E1/J1 card (rev 11) dahdi_scan So I have a card in a box - lspci shows it... dahdi_scan reports nothing. Is my card dead? Jerry -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, On a Lenny system, with dahdi 2.4.0, libpri 1.4.11.5 and asterisk 1.6.1.18, I inserted a new Digium HA8 + B400M card. My usual installation fails. I can see it listed : # lspci -n | grep d161 01:0b.0 0200: d161:8007 (rev 11) # lspci -vn 01:0b.0 0200: d161:8007 (rev 11) Subsystem: d161:8007 Flags: medium devsel, IRQ 22 I/O ports at d400 [size=256] Memory at

I installed 1 MDS , 2 OSS/OST and 2 Lustre Client. My MDS shows: [code] [root at MDS ~]# lctl list_nids 10.94.214.185 at tcp [root at MDS ~]# [/code] On Lustre Client1: [code] [root at lustreclient1 lustre]# lfs df -h UUID bytes Used Available Use% Mounted on lustre-MDT0000_UUID 4.5G 274.3M 3.9G 6% /mnt/lustre[MDT:0]

Hi guys, Another strange behavior with some test servers. They are booted using 2.6.11.12, xen-2.0.6, Debian. The only daemons running on dom0 are : xend, smtp, quagga (ospf), portmap (nfs client), sshd. Memory usage at startup is aroung 30 MB. Dom0 reserved memory is 256 MB. The only things that happen on this server are domU''s start/stop (xm create, xm shutdown) and a

Hi List, I'm finding a solution to provide failover and load balancing features to my IVR system. Anyone suggest me what is the best solution please?. what the hardware I should use ?. I heard about RedFone, but someone on the mail list said that it is not good because TDMoE module in asterisk is not so stable and TDMoE is stale. And It seems that RedFone doesn't not support load

After a reboot, I can't reproduce the problem anymore which is quite frustating. 2011/6/14 Tzafrir Cohen <tzafrir.cohen at xorcom.com> > On Tue, Jun 14, 2011 at 03:44:32PM +0200, Olivier wrote: > > Hi, > > > > I'm using a two-years old installation script for the first time on a > > Squeeze (linux 2.6.32) platform. > > For an unknown reason (might

We have a recently deployed server with a new TDM2400 card that will not put dialtone or audio on FXS ports after the physical server restarts (though they will ring if called, there's just no audio on the line if the phone at the other end picks up). The symptom can be resolved by stopping Asterisk, restarting DAHDI, and then restarting Asterisk. So far, this has happened on both times the

Thanks for the comment. The next pass for a file format ... ------ FILE BEGINS ----- # Comment lines [menu] item="text to display" status="status line text" action= SUBMENU | INACTIVE | whatever submenu= <number> data="arbitrary string" item="text to display" status="status line text" action= SUBMENU | INACTIVE | RUN | EXIT submenu=

All, We have recently updated our password aging to include setting inactivity days. We are running ossh 4.1p1 in a Solaris 8 environment. It appears that ossh isn't picking up on inactivity. Accounts that have been inactive still prompt to change passwords - if you telnet the same servers you get kicked out immediately. On the Solaris 9 servers running SUN's ssh the inactive accounts are

Hi, Recently We've upgraded some KVM hosts from Fedora 29 to Fedora 30 and now experience broken VM configurations on filesystem after virsh blockcommit. Commands "virsh dumpxml ..." and "virsh dumpxml --inactive ..." is showing diffrent configuration than the one on filesystem. In case of restart libvirtd or system reboot, there are broken VM xml configurations on

Hi, Can I make e&m wink start lines just wait for digits - instead of going to default? Someone else cleared a similar problem (as described below) on an fxo port with "usecallerid => no" but it is not doing the trick for me. In this case the line when straight to default which would be ok also. John I posted the stuff below about a week ago... I set up a t1 from my sys75 to

i am trying to list active + defined and inactive + defined domains using libvirt 0.9.4 i can get active domains using: def s_activedomains(conn): #get active domain ids numofdomains=libvirt.virConnect.numOfDomains(conn) activedomains=libvirt.virConnect.listDomainsID(conn) return activedomains i am stuck on how to get inactive domains the example listed

I have an Asterisk@Home 1.3 server (Asterisk 1.0.9) and recently added a TDM400P with (1) FXO card on port 4. Inbound calls are always successful but outbound calls fail 75% of the time with intercept messages from my dial tone provider that include "we're sorry, your call did not go through", and "we're sorry, when placing a local call it is now necessary to dial an area