similar to: h235 for authenticating RAS message

All, I'm running (attempting to) ooh323 with Asterisk and a Cisco 2621XM router operating as a H.323 GateKeeper, however when I bring the Asterisk box up it registers successfully with the GateKeeper (exchanges GRQ/GCF, then RRQ/RCF) it notes the GateKeeper supports keepalive at 300 seconds, when it gets to time to re-register its sends an RRQ again and gets rejected with RRJ (unspecified

Hello, I've been trying to send traffic to a Cisco Call Manager 3.2, but with no luck. Here's whats happening: * Call gets to CCM * Call gets to the gateway * Rings a couple times on destiny * Call gets hungup. On the CCM I get the following error: MediaManager - ERROR wait_AuConnectErrorInd On the Gw (Cisco AS5300) I get a disconnect cause of 2F (Resource not available) On asterisk:

Has anyone had any luck getting Asterisk 1.6.2.13 to register to a Tandberg Gatekeeper? The logs on the Asterisk end seem to show that the registration request is sent, and the Tandberg Gatekeeper responds. However, the response doesn't seem to be what Asterisk was expecting. Here is my ooh323.conf, followed by the relevant portion of the h323_log: [general] port = 1720 bindaddr =

I have tried everything. to register with this gatekeeper to make and receive calls These are the details I received from the voip provider: protocol H.323 Gatekeeper Address - AVS@210.21.118.XXX Port - 1719 RAS - 53 Q931 - 80 h245 - 1722 RTP - 1722 Username - H323 I have 2 phone number/accounts with this gatekeeper that I need to register to. ID - HMA0200.10szxn-xxxx e.164 - 22xx2912

I'm trying to connect an Asterisk 1.6 to an Avaya with gatekeeper (CLAN). When chan_ooh323 first loads it tries to establish a connection with the gk but I it fails. I have the following extract from the ooh323 log. Can anyone give some insight? Thanks! MD 23:02:59:045 Sent GRQ message 23:02:59:045 GkClient Received RAS Message 23:02:59:045 Received RAS Message = { 23:02:59:045

Hi, I'm trying to configure Asterisk as SIP-H.323 Gateway via ooh323, but I have an error relatively to the GK Confirmation message. >From the log: "H323 RAS channel creation - succesful Sent GRQ message Gatekeeper Confirmed (GCF) message received ERROR:No Gatekeeper ID present in received GKconfirmed message Ignoring message and will retransmit GRQ after timeout Error: Failed to

Hi, I've oh323 chan installed and working to make calls from SIP to H323 devices. The problem is can no hear sound with the H323 device. I think this is some related with codecs o nat, because the H323 have one public IP from a different subnet from the asterisk box. If I use netmeeting in gateway mode, the call can be completed and I can talk with a SIP device, but in gateway mode I can not

I've complied the OH323 .so successfully and can easily receive calls from my H323 gatekeeper (using 711u), however it seems that all outgoing calls are refused and I'm getting "reason 23 (Temporary failure)" as an error code which I can't find documented everywhere. My H323 gatekeeper needs a 001NXXNXXXXXX to dial out to the PSTN even if I'm in north america (Montreal)

Greetings to All, I hope someone has already gotten this working. I spent all day today trying to get ooh323 and gnugk to run on the same box. After a lot of tweaking to get everything compiled, I got both up and running. I can make calls IAX to H323, but cannot make calls in the reverse direction. I have tried many different configs on the GK, but always come up with the same error. It appears

I try to get H323 to run, but have so far only partial success: There is a Gatekeeper GK, where asterisk connects to. The Gatekeeper sees Asterisk, and Asterisk sees the gatekeeper. From the Network on the GK, asterisk is reachable via the number 070333333. I have an extension on asterisk 6002, which is reachable. I try to call a number attached to the gatekeeper (070168177) with the

All, I'm haveing a bit of trouble getting my head around H.323 and call routing with Gatekeepers, Zones and intra-zone calls - hopefully someone who is more informed in things H.323 will be able to point me in the right direction...? I already have a mature network of Asterisk boxes dotted around the UK and overseas with hundreds of extensions and our own number-plan/dial-plan in the form

hello everyone i have a simple question: i have an asterisk which is a h323 gateway and has a h323 connection to a cisco gatekeeper and a sip connection to a pbx. my question is: how can i send all calls to gatekeeper? i searched a lot and found that i should set gatekeeper=192.168.0.X (ip address of my gatekeeper) in h323.conf file. but what about extensions.conf file? should i define an

Actually I am facing a problem with H.323 (the standard and the ooh323) with Asterisk vesion 1.4.25 and I discover the following: 1) Using the standard h323 that come with Asterisk: The chan_h323.so it is not existed in the /usr/lib/asterisk/modules after doing the compilation and installation for (pwlib, openh323, /chanels/h323, asterisk), although make menuselect was done and the h323 channel

Hello All Anybody had used ooH323 for asterisk i using ooH323-0.7.2 and asterisk CVS may 2005. OpenH323 1.17.1 and pwlib 1.9.0 and GNUGK 2.0.2 audio is very good, better than SIP and IAX, but i have problem. how to router call from openh323 to outside PSTN. my h323.conf setting ; Objective System's H323 Configuration example for tvcti ; ooh323c driver configuration ; ; [general]

Dear Mailinglist-User currently we`re working with an IP-PBX, based on Asterisk, with SIP, H.323 and ISDN-Capabilities. SIP and ISDN works fine, but H.323 not. In our first test, we started to connect Asterisk to an Cisco IOS-Gatekeeper with the "chan_oh323" (version 0.6.5). We successfully tested in/egress calls without any problems. But when we started to connect our Asterisk

Hi, I am trying to communicate H323 and SIP users. I have configured h323.conf, sip.conf and ooh323.conf. If I am using gatekeeper (gnugk) then I am able to call successfully to h323 users using SJphone. And same for SIP users also. But when I disabled gatekeeper and trying to call using gateway with sjphone then every time whatever number I dial the call goes to asterisk and some computerized

Hi list, After several tries to understand the subtil description in the h323.conf to be able to make the next scenario I was presented the following error messages by asterisk. Can somebody tell me please what I am doing wrong. Scenario: Gatekeeper (h323) --> Asterisk PBX -->(h323) Gateway Endpoints are connected to Gatekeeper. Call does come in like 999931235650087 with codec g711

For the benefit of everyone, having H323 Configuration problem due to H245 Tunnel, check the h323 Config embeded at the end. Comment the offending line as under: ; ; Enable H.245 tunnelling (yes,no). ; h245Tunnelling=yes ; -----Original Message----- From: Tola Ogunsan [mailto:tolaniye@hotmail.com] Sent: Wednesday, May 25, 2005 1:03 PM To: Kanuri, Seshu (Company IT) Subject: RE: oh323 problems

OOH323 Debugging Enabled -- Executing Answer("SIP/3513-090f7d40", "") in new stack -- Executing Wait("SIP/3513-090f7d40", "1") in new stack -- Executing DeadAGI("SIP/3513-090f7d40", "a2billing.php|1") in new stack -- Launched AGI Script /var/lib/asterisk/agi-bin/a2billing.php a2billing.php|1: line:58 - IDCONFIG : 1

Hi All; First of all, I am looking to have the H323 Gatekeeper service available at Asterisk, and really I do not know if 1.4 or 1.6 or 1.8 started implementing H323 gatekeeper functionality or not? Until 1.4.26.2 version, there is no h323 gatekeeper functionality. So, any implementation for this feature has been done in the other versions?