similar to: Slow (Lagging) connection establishment via BRI

Hi All, I've a BT Versatility PBX that I want to connect to my asterisk 11.9.0 box via BRI port in NT mode but actually I wasn't able to get it working. I've another standalone PBX, it's a Panasonic model, which works fine connected to the same port. The BT connected to a UK BT BRI line works quite fine after roughly a minute once connected. The PBX can be seen at

Have you got termination set correctly? I have a B410P working with 2 x NT and 2 x TE ports successfully. I had to turn the 100ohm termination on on the NT ports (even though I have them set as PTP in mISDN.conf). HTH -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On

Brent- There is no good way to say what changing the hardware and PSTN hookup will probably do for the echo problems. I'm not sure if you mentioned (lost in the past history of your post now) what sort of hardware you're using for PSTN connection now- TDMs, X100s, ATA's, etc- but that could also be a potential cause. I've heard tell of aftermarket X100s and certain ATA's

Greetings - We've a pair of ISDN BRI that we use for dialtone, fairly happily except for the recent meltdown of one of our Netgear RT338's. We're in the middle of slowly migrating to a VoIP/Asterisk-on-FreeBSD based phone system. I had originally considered just buying a Digium TDM400 card and continuing to use the RT338's to bring out POTS lines from the BRI's, but the

Hi, I have a legacy Norstar system that I'm looking into integrating with my Asterisk setup. My first attempts have worked, which involves a Wildcard X100P FXO card in the * box connected to the Internal ATA (FXS port) on the Norstar system. Calling from SIP -> Norstar works fine, since the SIP caller initiated the call and generally will be sane enough to hangup the phone when

Hi, In my lab, I'm testing BRI spans in NT/ptmp mode. My setup is: asterisk 11.2.1 libpri 1.4.14 dahdi 2.6.1 wctdm24xxp (HA8 hybrid with B400M) SIP phone <----> Asterisk with HA8 <----> Patton SN4638 <----> Asterisk <----> SIP phone The single BRI line I'm testing remains down: CLI> pri show spans PRI span 1/0: In Alarm, Up, Active I'm quite certain this

Hi- Anyone using the Junghann's quad BRI card and the Digium E100P in the same system? I'm having a configuration problem where I can configure the cards one at a time (with the appropriate drivers loaded) in a system, but when I try them both together, neither will work. They both work fine one at a time. Probably has something to do with the channel numbering. I've tried

Hi, folks: I remain intrigued by the gap in BRI implementation between North America and Europe, and I wanted to get feedback from the list members on the matter. I'm seriously considering making the leap in our office. In Europe, the idea that an office that does not have enough lines to justify PRI would use analog lines is perceived as technologically backwards, and yet that's what

Hello everybody, I try to install -Ubuntu 8.04 server- a B410P and a TDM2400P together with Asterisk 1.4.26-2, dahdi-linux-2.2.0.2 and dahdi-tools-2.2.0. Problem I face is the following one: CLI> module load chan_dahdi.so == Registered application 'DAHDISendKeypadFacility' == Registered application 'ZapSendKeypadFacility' == Parsing

Good Evening, The company I work for is attempting to connect an Cisco ISDN Router to an OpenVOX B200P BRI Card so that we can get it to dial out across an existing ISDN PRI Line also installed in the Asterisk PBX Everything has compiled successfully and the BRI card has been detected when mISDN is started: # misdnportinfo Port 1: NT-mode BRI S/T interface port (for phones) -> Interface

Hello- I have a system with one D410P and one B200P (both OpenVox). All is well with the D410P, inbound and outbound, and I can initiate calls on the B200P BRI span, but there may be something wrong with my inbound BRI setup: there is no indication of an inbound call when I dial in to it from the PSTN. When I run "pri intense debug" and make a call to the BRI span, I can see a

Hi ""noobs"" and others(like me). I've been struggling for hours,days,days,days.... to get my Asterisk work with 2x HFC-S BRI cards. One card for use in NT-mode for connecting my ISDN DECT phone,and one card as gateway to PSTN. Now it'works,and I just want to share some of the experience with others. I'd guess there must be 'Somebody Out There' having

We have quadBRI configured 1 port in TE mode 2,3,4 ports in NE mode. We are trying to place a call from the phone connected to BRI card port #4 to city number through ISDN line connected to port #1. Number successfully dialed. Person on the other end answering the line. But conversation can't last more then 10 seconds. Below is a log of such call. Its not clear for me why we appear in

I am trying to connect asterisk to my PCI ISDN BRI card. I modify the modem.conf file and it runs just fine…giving the result [chan_modem.so] => (Generic Voice Modem Driver) == Parsing '/etc/asterisk/modem.conf': Found == Loading modem driver chan_modem_i4l.so => (ISDN4Linux Emulated Modem Driver) but then it gives the error saying… Sep 20 15:13:57

Hi all, As i tested with Asterisk+dahdi+libpri with openvox BRI with NT mode, the ISDN phone does not work. There is the setting and error. ***********************Enviroment***************************** Asterisk-1.6.1.18 dahdi-linux-2.3.0.1 dahdi-tool-2.30. libpri-1.4.11.2 CentOS-5.5 OpenVox B400P ****************************************************************** In my case , I set prot 1 and

Hello all Asterisk 1.2.10 BRIstuff PRE-1s Debian sarge I have an issue with my ISDN-BRI line. Asterisk tells me my D-Channel is down, no matter is I have an actual line plugged in or not. == Primary D-Channel on span 1 down I somehow got it to work once! The config tools do not indicate any errors whatsoever. Here is a rundown of various listings I can think about. (some things may show

Hi All, The link http://www.voip-info.org/wiki-Asterisk+Data+Configuration talks about how a Digium PRI card can be setup for data, and also be used by asterisk to handle voice. Is the same or similar possible with BRI ? There are a few links on the Wiki to BRI cards, and that BRI can be supported through CAPI compatible hardware. That will take care of voice. What I want to do is use a BRI

Hi All, I currently run asterisk in our office (in Japan) and use a cisco PRI gateway for connection to the PSTN. I would like to setup some more systems for our smaller offices (in Japan) that would use BRI and preferably using a PCI card in the asterisk box and not a seperate Cisco gateway (expensive). HOWEVER, Japan has this INS64 protocol for their BRI lines and im not sure what cards

Hello everyone, I'm hoping someone can help me with this. I have a business customer in the U.S. (Michigan, AT&T Territory). I need to get 4 trunks into an asterisk Box. My intention is to use an Eicon Diva Server card with 2 BRI Circuits. The reason for this is that the business needs DID's on the trunks (20 of them). A full or fractional PRI is overboard for them, as they will

Hello, I need to connect one diva server 4bri to a portuguese BRI interface. The operator (PT) said that this bri is in point-to-multipoint mode (S0). Previously one PBX has connected to that interface. The asterisk and diva drivers are working ok but i cannot communicate to outside via this bri. Xlite gives me the message: "call failed: declined". Anyone have experience with this