similar to: APC Smart-UPS C1500 connected by usb

On Nov 8, 2014, at 6:12 PM, Selva Nair <selva.nair at gmail.com> wrote: > Everything works rather well, except that the cgi-interface does not report input/output voltages and load for the C 1500 unit. > upsc also reports these values only for model 1000, not for 1500. Battery charge is and runtime are reported. For the 1000, do the values match this page?

Hi Charles, Thanks for your response. > For the 1000, do the values match this page? > > > http://buildbot.networkupstools.org/~buildbot/cayman/docs/latest/ddl/APC/Smart-UPS_1000.html > > Yes it does (except that mine is a 120 V model, so input/output voltage is about 125) It doesn't look like we have an entry for a C1500 yet. Would you care to > submit the output of

Hi all, I am trying to get a APC Back-UPS CS 500 running on my QNAP 419P Nas. Since on all my work I figure out the following: from Network UPS Tools upscmd 2.4.1 [~] # upscmd -l qnapups Instant commands supported on UPS [qnapups]: beeper.disable - Disable the UPS beeper beeper.enable - Enable the UPS beeper beeper.mute - Temporarily mute the UPS beeper beeper.off - Obsolete (use

Hi, I had named a module as "global" and it appears not to be recognized. It appears a section [global] path=xxx etc. is interpreted as global parameters and not as a module named global. Is that the expected behaviour? Any pointers as to what names are allowed for modules will be appreciated. Thanks, Selva -------------- next part -------------- An HTML attachment was scrubbed...

On Tue, Oct 13, 2015 at 12:54 PM, Xen <list at xenhideout.nl> wrote: > Hi Folks, > > I was wondering if I could ask this question here. > > Initially when I was thinking up how to do this I was expecting block > encryption to stay consistent from one 'encryption run' to the next, but I > found out later that most schemes randomize the result by injecting a >

On Mon, 13 Jul 2015 17:38:35 -0400, Selva Nair wrote: > As with any dedup solution, performance does take a hit and its often > not worth it unless you have a lot of duplication in the data. This is so only in some volumes in our case, but it appears that zfs permits this to be enabled/disabled on a per-volume basis. That would work for us. Is there a way to save cycles by offering zfs

On Sun, Jan 24, 2016 at 4:48 PM, < dbonde+forum+rsync.lists.samba.org at gmail.com> wrote: > That doesn't make sense. Both the source and destination path contains > simple alphanumeric characters, no more no less. Why would it matter > whether the path is /abc/ or /def/ or even /123/? Hmm.. I thought your are the one who has been asking for help. It does very much matter

On 03/04/17 17.24, Roger Price wrote: > On Mon, 3 Apr 2017, Jon Bendtsen wrote: > >> On 03/04/17 17.10, Roger Price wrote: >>> On Mon, 3 Apr 2017, Jon Bendtsen wrote: >>> >>>> Power seem to be lost immediately. >>>> But my APC Smart-UPS 1500 always reported everything OK. >>>> battery.charge : 100 >>> ...

On Dec 7, 2013, at 2:38 PM, Christian wrote: > Dear list, > > I have an APC Smart-UPS 1500 hooked up via the USB port. Recently, when > we had a power outage, the only entry in the logs was: > > Dec 3 14:43:43 afs1 upsmon[3035]: UPS apc at localhost on battery > > and then the machine seems to have run until the battery was empty. It > only notices the "battery

On Mon, 13 Jul 2015 15:40:51 +0100, Simon Hobson wrote: > The think here is that you are into "backup" tools rather than the > general purpose tool that rsync is intended to be. Yes, that is true. Rsync serves so well as a core component to backup, I can be blind about "something other than rsync". I'll look at the tools you suggest. However, you've made be

Dear list, I have an APC Smart-UPS 1500 hooked up via the USB port. Recently, when we had a power outage, the only entry in the logs was: Dec 3 14:43:43 afs1 upsmon[3035]: UPS apc at localhost on battery and then the machine seems to have run until the battery was empty. It only notices the "battery low" after I turn the system back on: Dec 3 16:01:39 afs1 usbhid-ups[21973]:

On Sun, Jan 24, 2016 at 12:29 PM, < dbonde+forum+rsync.lists.samba.org at gmail.com> wrote: > On 2016-01-24 03:51, Kevin Korb wrote: > >> Are you rsyncing from one to the other? Both of them to somewhere >> else? One at a time to somewhere else? Why won't you just show your >> actual command line and an ls -li of the correct source and incorrect >>

Hi, I have problem with upssched on windows. Upssched is not executed. I have 2 scripts, 1 for notification in upsmon and second for scheduling in upssched. Monitoring is working fine, script write to log. I'm using binary windows installer 2.6.5-6 from NUT. Here are my configs: --- nut.conf MODE=netclient --- upsmon.conf MONITOR ups_1000 at 192.168.3.95 1 <user> <password> slave

Hi Yesterday I had 2 different APC UPS using USB get in power off recoverable state. dmesg said: 7705944.352083] usb 2-1: new low speed USB device using uhci_hcd and address 2 [7705944.477061] usb 2-1: device descriptor read/64, error -71 [7705944.709035] usb 2-1: device descriptor read/64, error -71 [7705944.925071] usb 2-1: new low speed USB device using uhci_hcd and address 3

hi all, I have a matrix and named each row and column as like below... a<-matrix(c(seq(3,45,3),seq(10,6,-1)),4,5,byrow=F) > col<-c("peter","david","richrd","vincent","selva") > rows<-c("julius","caeser","anja","maya") > dimnames(a)<-list(rows,col) > a peter david

I have used the patch to build opus 1.1. Although I have not tried the latest git master, will try that. Will that work for armv7, armv7s and arm64? On Wed, Mar 26, 2014 at 11:01 PM, Martin Storsj? <martin at martin.st> wrote: > On Wed, 26 Mar 2014, Jonathan Lennox wrote: > > >> On Mar 26, 2014, at 7:55 AM, Peter Robinson <pbrobinson at gmail.com> wrote: >>

Hi, I am trying to compile Samba 2.2.2 on Solaris 2.8. I am using GCC 3.0.2 compiler. While compiling it gives error and stops. The config.log file shows that conftest.c file cannot be found. Through mailing list I came to know that this file is created on the fly. I am compiling as root and I have set the permissions properly. Is the problem with PATH ? if so what path should be mentioned in

If my sample size is small is there a particular switch option that I need to use with t.test so that it calculates the t ratio correctly? Here is a dummy example? á =0.05 Mean pain reduction for A =27; B =31 and SD are SDA=9 SDB=12 drgA.p<-rnorm(5,27,9); drgB.p<-rnorm(5,31,12) t.test(drgA.p,drgB.p) # what do I need to give as additional parameter here? I can do it manually but

2017-04-04 14:18 GMT+02:00 Jon Bendtsen <jon.bendtsen at jonix.dk>: > On 04/04/17 14.10, Roger Price wrote: > >> On Tue, 4 Apr 2017, Arnaud Quette wrote: >> >> > [cuuuuut] > > Hi Arnaud, It seems to me that, looking out into the future, there are >> three >> things upsmon needs: >> >> 1. A fall-through <notify type> of

We are scheduling another meeting to discuss Theora matters. One of these was planned just a while ago, but it pretty much didn't happen. So let's make this one happen. Anyone interested in Theora or video technologies is welcome to attend. The place is #xiphmeet at irc.freenode.net, this Tuesday at 14:00 UTC. If you don't know when 14:00 UTC is, go here[1] for conversion into