similar to: Belkin F6C1100-UNV

Hi, it'd be great if you could update the documentation on the website that some models of the Belkin -UNV series will only work with the megatec(_usb) drivers. I wasted a lot of time on trying to get it to work with the wrong drivers, and would like to spare others the pain :-). Thanks, ~David P.S. Some forum post said that the stable megatec drivers don't work 100% with the belkin UPS,

Hi, it'd be great if you could update the documentation on the website that some models of the Belkin -UNV series will only work with the megatec(_usb) drivers. I wasted a lot of time on trying to get it to work with the wrong drivers, and would like to spare others the pain :-). Thanks, ~David P.S. Some forum post said that the stable megatec drivers don't work 100% with the belkin UPS,

I'm trying to set up a belkin f6c1100-unv UPS to work with nuts. From reading the mailing list, it sounds like the belkinunv serial driver should work and that the USB driver is potentially troublesome. Is this a correct impression? Also I may have missed this but if I do go with the serial (or USB port) is there any simple command line method for verifying basic connectivity? The

Hi, I've been fighting with trying to get a Belkin Universal model F6C800-UNV to work with NUT. The error I am getting is as follows: ---------------------------------------------- * Starting UPS drivers ... Network UPS Tools - UPS driver controller 2.0.0 Network UPS Tools - Belkin 'Universal UPS' driver 0.06 (2.0.0) tcgetattr(/dev/ups): Inappropriate ioctl for device Driver failed

For the record, I was able to get the following working: Device: Belkin F6C1500-TW-RK Driver: belkin I tried the "belkinunv", which I use for my F6C1100-UNV, but it didn't work. At least there was a driver that worked! :-) Feel free to add it to the list of "tested" configs. Thanks, Dave ---------------------------------------------------------- Are Your Friends

Hello, all, I had been using NUT's Ubuntu package (64 bit) with no problems until upgrading to Ubuntu 11.04. Now, I get the following message when I try usbhid-ups: $ sudo /lib/nut/usbhid-ups -a mybelkin Network UPS Tools - Generic HID driver 0.35 (2.6.0) USB communication driver 0.31 Can't claim USB device [050d:1100]: could not detach kernel driver from interface 0: Operation not

Oh oops, I see you already did. -- Peter selinger wrote: > > You could send it without "submitting" it. That's the advantage of > patches - they can be discussed. There are lots of eyeballs here that > might see what's wrong. Thanks, -- Peter > > Eric S. Raymond wrote: > > > > Peter Selinger <selinger at mathstat.dal.ca>: > > > I

Hi everyone, I have a belkin ups that was bought around 2 months ago. It seems like the driver doesn't like the UPS, although on the website it's listed as supported. This is on a gentoo system with nut 2.2.1 . megatec_usb output: ---------SNIP---------- digamma nut # ./megatec_usb -a belkinm -DDDDDD Network UPS Tools 2.2.1 - Megatec protocol driver 1.5.9 [megatec_usb] Carlos Rodrigues

Hi everybody, I've got an Unitek iZi UPS 525 with a serial interface. The supplied cable looks fairly simple: RX->RX , TX->TX and GND->GND. Using this cable and Minicom with 2400 8N1 I'm able to issue commands to the UPS using the "Megatec Protocol" http://www.networkupstools.org/protocols/megatec.html so I know the UPS is fairly "intelligent" :-) and the

Hi, is there a way to use my Belkin F6H650 on the USB port? I already installed usbhid-support, but neither the hidups worked (reports "/dev/usb/hiddev0 is not a UPS") nor genericups with upstype=7 and the hiddev set as device ("ioctl TIOCMSET: Invalid argument") worked. I have installed the debian sarge package of nut 2.0.1 (2.0.1-4) Regards, Philipp

Greetings all; I pulled a Belkin F6C100-4 into the shop this afternoon, deader than a door nail. Out of service for about a year because (I'm assuming here) that the cooling fan stopped and cooked what little remaining life there may have been out of the batteries, which had swelled so badly I had to split its frame to get them out. They are also in the under 1 volt per 12 volt pack

Hi all - I'm new to both UPS setup and SNMP on linux - so I'd appreciate any help I can get....I'm stuck! I'm running fedora core 5, and have installed net-snmp and nut. I'm trying to get my network connected UPS to this linux machine. My /etc/ups/ups.conf looks like this: [upsnetwork] driver = snmp-ups port = 172.31.254.7 community = public desc="Network

Hi Arjen My apologies fro drifting off topic in the other mailing list...:-) On the bottom of the Belkin UPS unit - is the model number: F6C120auUNV The "au" is for Australia I think. "man belkinunv" states that F6C120-UNV is supported - and I assumed that the "au" would not prevent this. I plugged in the USB to gather the information you requested. My intention

Dear Andreas, some googling revealed, you created a driver for the xanto series of online-usv.de. In what state it is currently? I've to manage a S2000 and would like to use nut for it, is it usable by now? Do you need another tester? TIA, Pete

Zaid, I have a Belkin F6C800-UNV which has both a serial and USB connector. The serial connection is already working with the Belkinunv driver. I will connect via the USB and then compare both sets of variables. This should allow me to correlate and shed some light on the meaning of many of Belkin's non-standard "Usage" descriptors. With this information, it should be very easy

Hi Patrick, 2006/4/2, Patrick Beard <p.beard@blueyonder.co.uk>: > Hi Arnaud, > > Just wanted to let you know the the Belkin F6H500ukUNV is working for me > with the fentonups driver. > > http://catalog.belkin.com/IWCatSectionView.process?IWAction=Load&Merchant_Id=&Section_Id=202840 > > I originally tried it with the genericups driver with upstype=7 but this

I recently installed NUT 2.2.1 and set it up with a Belkin F6C100-UNV. I can monitor it via serial (belkinunv) or USB (usbhid-ups) cable, and both do seem to work fine, but I would prefer USB to avoid having to add a PCI serial card to the machine. I had to unplug something else to try it with a serial cable. Using 'belkinunv', there's a "-x wait" option: [ from

Hi. My Belkin UPS F6C1100-UNV works fine with megatec_usb version 1.6 (2.4.1). However, it doesn't work with 2.4.2 nor 2.4.3. # /lib/nut/megatec_usb_old -D -a belkin Network UPS Tools - Megatec protocol driver 1.6 (2.4.1) Serial-over-USB transport layer 0.10 debug level is '1' Starting UPS detection process... 0 out of 5 detection attempts failed (minimum failures: 2). Cancelling

Hello, I am trying to understand how to create a custom configuration for the genericups driver. My system simply signals RI on a serial port on low battery. That's it, nothing else. This serial port is also being used for communications so the other lines are going to be changing all the time, unrelated to the UPS state. Is there a "null" upstype I can use, and then add LB=RNG?

I have a new Belkin F6C900-UNV. I see that it's not listed in belkin-hid.c The VendorID is 0x050d like all the Belkin UPSes, and the ProductID is 0x0900. I haven't had a chance to actually test the development version of nut yet, since I'm running Fedora Core 6, which still has nut 2.0.3. `newhidups -DD -a myups` gives the error of: Checking device (050D/0900) (001/002) - VendorID: