similar to: Fenton Powerpal L1400R "Not Supported" message...

Hi there Would anybody happen to know the correct driver for a Fenton Powerpal S series? upsdrvctl reports: Network UPS Tools - UPS driver controller 1.2.2 Network UPS Tools - Fenton UPS driver 0.90 (1.2.2) Unknown ups - please report this ID string: #FENTON S Series V4.04EG503 Detected Unknown Series on /dev/ttyS0 Alternatively, does anyone know if the manufacturer is likely to

Hi There, i have a strange problem with a fenton powerpal 660. When you switch off the power to the UPS (from the wall), the server (IBM xSeries 203) attached to it dies...However, if you unplug the cable from the server to the UPS and plug it back in again (with the power still out to the UPS), the server starts up again (set to power up after a power failure) and runs with no issues. I have

Hi ups-devel, As I looked throw www.networkupstools.org site, haven't found any pointers where to send patches, so I hope this is the right place. (Please let me know weather this is the right place.) The patch contains a minor change in the logic of the driver, our Effekta MHD 3000 UPS continuously writes status data to the serial port, so one has to send a CR character and empty the

Hi Henning, you should get in touch with Carlos, who his developing a generic megatec driver (available from svn: http://eu1.networkupstools.org/source.html) Arnaud -- Linux / Unix Expert - MGE UPS SYSTEMS - R&D Dpt Network UPS Tools (NUT) Project Leader - http://www.networkupstools.org/ Debian Developer - http://people.debian.org/~aquette/ OpenSource Developer -

Hi, I have a Fenton Powerpal L660, when I try and configure nut with either the metatec or fentonups driver, and start upsd, the UPS instantly turns itself off. It used to work, until I changed my motherboard and CPU, which means it has a different bios and serial port setup. This is happening with Nut 2.0.1 and also Nut 2.0.5. I have an AMD64 bit processor, Mandriva 2007 64 bit. Any

2007/2/19, Glen Ogilvie <nelg@linuxsolutions.co.nz>: > Hi, > > I have a Fenton Powerpal L660, when I try and configure nut with either the > metatec or fentonups driver, and start upsd, the UPS instantly turns itself > off. > > It used to work, until I changed my motherboard and CPU, which means it has > a different bios and serial port setup. > > This is

2007/2/19, Glen Ogilvie <nelg@linuxsolutions.co.nz>: > Hi, > > I have a Fenton Powerpal L660, when I try and configure nut with either the > metatec or fentonups driver, and start upsd, the UPS instantly turns itself > off. > > It used to work, until I changed my motherboard and CPU, which means it has > a different bios and serial port setup. > > This is

G'day. I have a UPS here that is driven by the Fenton UPS driver, and which requests that I report the ID string to the NUT developers: root@anu:~# upsdrvctl start smk800 Network UPS Tools - UPS driver controller 2.0.4 Network UPS Tools - Fenton UPS driver 1.22 (2.0.4) Unknown ups - please report this ID string: #M+H SMK-800 2000 V6.2 Detected Unknown MK-800 on /dev/ttyS0 The

Gidday all - I'm a new user to nut. I've got some cheap powerpal UPSs working fairly well. However I also have a new Dynamix UPS-1700D and an old Powercom KIN-1700 something unit that I cannot make work right. The best method I've found is "trial and error" which sounds a bit last-resort. Is there any better way to find out what protocol is used? -- Criggie

Hi Patrick, 2006/4/2, Patrick Beard <p.beard@blueyonder.co.uk>: > Hi Arnaud, > > Just wanted to let you know the the Belkin F6H500ukUNV is working for me > with the fentonups driver. > > http://catalog.belkin.com/IWCatSectionView.process?IWAction=Load&Merchant_Id=&Section_Id=202840 > > I originally tried it with the genericups driver with upstype=7 but this

Hi *Simon, i got a similar setup here (also a powercom-oem-product, but in my case labeled by a swiss "manufacturer") with the same problems, using powercom's upsmon works fine, while nut completely refuses to cooperate. after trying almost everything i somehow hopeless surfed on the official nut-page, when i saw that there are powercom-products which don't need the

Hi Alexander, > I've UPS named PowerMan RealSmart 1000, it is not listed in > compatibility list. I found that it works with "fentonups" driver and > have ups.model "Unknown S163-1000". Ithink "1000" is from capacity - > I've seen in Internet someone have RealSmart 800 identified "S163-800". > Also PowerMan have

Hello everybody, this is my first post to this list - normally I take some time to read some messages first to get an impression of the List, but I have a pressing question to ask, so please forgive me if I miss the right tone... I just installed NUT 2.0.2 and try to get it working with our Effekta MT 1500. In the Drievers List I found this entry: "Effekta" "MI/MT/MH"

Hi, I am working on a patch for FENTON.H to support some more ups models, I wonder if someone can help with further information,meaning and importance for the following values that are beeing set in the model capability table: float lowvolt; float voltrange; float chrglow; float chrgrange; int lowxfer; int lownorm; int highnorm; int highxfer; Thanks, Nadav

Hi I'm hoping someone can help. I'm running fc5 with nut 2.0.3. I just recently acquired 2 Gamatronic SmartCompact ups for my Linux boxes. As you can see from the info below, everything looks ok. When I unplug the ups from the wall, after a while, the computer shutdowns very rudely. That it is just turns off. No scrolling down of processes shutting down It does not seem shutdown

Hello nut-upsuser, Hope, that its might be useful for someone: 1. Kebo UPS-600A Driver: genericups UPStype: 7 Config extras: SD = -RTS or SD = -TX (don't know why but both are suitable) 2. Kebo UPS-1200M Driver: fentonups Config extras: none Note: Looks like twin brother of Microlab UPS-1200M :) Driver ask me to report ID string: "Unknown

Hi Stefanos, you should mail to the NUT list, and try the megatec driver, which is only available from subversion for the moment (but should be included in the next stable release). Carlos might give you some help with this driver. Arnaud Quette -- Linux / Unix Expert - MGE UPS SYSTEMS - R&D Dpt Network UPS Tools (NUT) Project Leader - http://www.networkupstools.org/ Debian Developer -

Hi guys, Please bare with me, as this is my first attempt at setting up a UPS under Linux. I've been trying to setup a UPS on one of my clients servers. The model of the UPS is a Square one QP1000/QP1010 1Kva I've looked on the following link http://eu1.networkupstools.org/compat/stable.html It says that it should be compatible with the "powermust" driver, then in my

Hi everybody, I've got an Unitek iZi UPS 525 with a serial interface. The supplied cable looks fairly simple: RX->RX , TX->TX and GND->GND. Using this cable and Minicom with 2400 8N1 I'm able to issue commands to the UPS using the "Megatec Protocol" http://www.networkupstools.org/protocols/megatec.html so I know the UPS is fairly "intelligent" :-) and the

I had some free time this weekend, and made some long overdue changes to "megatec". The thing is, these changes lead to a couple of questions that I must ask before I go on and "svn commit" them: 1) The blazer, fentonups, esupssmart, ippon, sms and mustek drivers are now completely covered and all of their functionality should now be present in megatec, and also every model