similar to: cannnot load drivers for a Belkin F6C800-UNV

Zaid, I have a Belkin F6C800-UNV which has both a serial and USB connector. The serial connection is already working with the Belkinunv driver. I will connect via the USB and then compare both sets of variables. This should allow me to correlate and shed some light on the meaning of many of Belkin's non-standard "Usage" descriptors. With this information, it should be very easy

All, I just bought a Belkin F6C1100-UNV and am trying to get it to work with NUT. I have tried many drivers ( "belkin", "belkinunv", "genericups upstype=4", and "genericups upstype=7", "bestups", "fentonups"). None of them seem to work. Does anyone have any experience with this device? If there is some utility that you all use to

Just a little tiny detail : ============================================================================== > --- trunk/scripts/hotplug/libhid.usermap (original) > +++ trunk/scripts/hotplug/libhid.usermap Fri Aug 25 19:18:19 2006 > @@ -21,5 +21,7 @@ > libhidups 0x0003 0x09ae 0x1003 0x0000 0x0000 0x00 0x00 0x00 0x00

Hi, it'd be great if you could update the documentation on the website that some models of the Belkin -UNV series will only work with the megatec(_usb) drivers. I wasted a lot of time on trying to get it to work with the wrong drivers, and would like to spare others the pain :-). Thanks, ~David P.S. Some forum post said that the stable megatec drivers don't work 100% with the belkin UPS,

Hi, it'd be great if you could update the documentation on the website that some models of the Belkin -UNV series will only work with the megatec(_usb) drivers. I wasted a lot of time on trying to get it to work with the wrong drivers, and would like to spare others the pain :-). Thanks, ~David P.S. Some forum post said that the stable megatec drivers don't work 100% with the belkin UPS,

Greetings all; I pulled a Belkin F6C100-4 into the shop this afternoon, deader than a door nail. Out of service for about a year because (I'm assuming here) that the cooling fan stopped and cooked what little remaining life there may have been out of the batteries, which had swelled so badly I had to split its frame to get them out. They are also in the under 1 volt per 12 volt pack

I'm trying to set up a belkin f6c1100-unv UPS to work with nuts. From reading the mailing list, it sounds like the belkinunv serial driver should work and that the USB driver is potentially troublesome. Is this a correct impression? Also I may have missed this but if I do go with the serial (or USB port) is there any simple command line method for verifying basic connectivity? The

Hi Arjen My apologies fro drifting off topic in the other mailing list...:-) On the bottom of the Belkin UPS unit - is the model number: F6C120auUNV The "au" is for Australia I think. "man belkinunv" states that F6C120-UNV is supported - and I assumed that the "au" would not prevent this. I plugged in the USB to gather the information you requested. My intention

I recently installed NUT 2.2.1 and set it up with a Belkin F6C100-UNV. I can monitor it via serial (belkinunv) or USB (usbhid-ups) cable, and both do seem to work fine, but I would prefer USB to avoid having to add a PCI serial card to the machine. I had to unplug something else to try it with a serial cable. Using 'belkinunv', there's a "-x wait" option: [ from

Hello, all, I had been using NUT's Ubuntu package (64 bit) with no problems until upgrading to Ubuntu 11.04. Now, I get the following message when I try usbhid-ups: $ sudo /lib/nut/usbhid-ups -a mybelkin Network UPS Tools - Generic HID driver 0.35 (2.6.0) USB communication driver 0.31 Can't claim USB device [050d:1100]: could not detach kernel driver from interface 0: Operation not

I have a new Belkin F6C900-UNV. I see that it's not listed in belkin-hid.c The VendorID is 0x050d like all the Belkin UPSes, and the ProductID is 0x0900. I haven't had a chance to actually test the development version of nut yet, since I'm running Fedora Core 6, which still has nut 2.0.3. `newhidups -DD -a myups` gives the error of: Checking device (050D/0900) (001/002) - VendorID:

I just moved my UPS over from serial to USB and found that I needed to add it to the hotplug USB list to make things work. Belkin F6C120-UNV - Bus 002 Device 004: ID 050d:0912 Belkin Components It seems to be working OK on 2.0.4 with newhidups. Attached is a patch which I think should add the appropriate device id's in the right places to the trunk code. Jon -------------- next part

Peter, Apparently, some Belkin UPSes still have problems with this. When we receive this report through the interrupt pipeline it is ignored (the special case in usbhid-ups.c) and even after that it looks like there are still some problems with it: http://lists.alioth.debian.org/pipermail/nut-upsuser/2007-July/003014.html Wouldn't it be an option to just to ignore this completely and

Mr. Selinger, I'm CCing you directly since it appears (insofar as I can tell) that you are one of the delelopers for the newhidups driver. This is the third time I've submitted this (hence the CC this time). Hopefully mailman takes it. I've tweaked my SPF records, and I'm hoping that was the problem. My sincere apologies if this has gone through and I just haven't seen it

This model is available in AU/NZ and can work as USB or serial. It uses the cutdown Bulldog software that comes with the cheaper serial based belkin models, and they don't officially support the USB mode under Linux. Anyone managed to get this working with NUT using either serial or USB? I'd really like to get the extra functionality of the NUT tools vs the very simple setup of the

Oh oops, I see you already did. -- Peter selinger wrote: > > You could send it without "submitting" it. That's the advantage of > patches - they can be discussed. There are lots of eyeballs here that > might see what's wrong. Thanks, -- Peter > > Eric S. Raymond wrote: > > > > Peter Selinger <selinger at mathstat.dal.ca>: > > > I

For the record, I was able to get the following working: Device: Belkin F6C1500-TW-RK Driver: belkin I tried the "belkinunv", which I use for my F6C1100-UNV, but it didn't work. At least there was a driver that worked! :-) Feel free to add it to the list of "tested" configs. Thanks, Dave ---------------------------------------------------------- Are Your Friends

Greetings! Thanks to all the developers who have made this project so far. Searching for a Linux based Belkin UPS monitor led me straight to the Network UPS Tools. I have bought a Belkin F6C900-UNV (900VA) for use on a Slackware 10.2 server to replace an older APC model that died suddenly. So far I have successfully managed to get NUT 2.0.5 compiled and configured and found that this Belkin

Hi everyone, I have a belkin ups that was bought around 2 months ago. It seems like the driver doesn't like the UPS, although on the website it's listed as supported. This is on a gentoo system with nut 2.2.1 . megatec_usb output: ---------SNIP---------- digamma nut # ./megatec_usb -a belkinm -DDDDDD Network UPS Tools 2.2.1 - Megatec protocol driver 1.5.9 [megatec_usb] Carlos Rodrigues

Hi I'm sending this to you as it appears that you are the person who looks after and/or supervises the code for NUT's Belkin drivers. I'm using the address you use for the Nut-upsdev mailing list ( selinger at mathstat.dal.ca ). Anyway... I have a Belkin Universal UPS and, having just upgraded my Fedora Core system from 4 to 5 and had to go back through the system RC files