similar to: Old Contact UPS Info

Hello, I have one UPS Infosec XP Pro 2500 RM and it works with windows sw RUPS2000. Now I want to install this UPS as virtual server on vmware ESXi vMA - (SUSE SLES 11SP2 linux). On this linux I have NUT 2.6.0 and I stopped now with configuration of genericups driver. Working cable (direct cable pin1-pin1 ... pin9-pin9) connection on Windows: PIN | PC | UPS

My UPS is an Exide NetUPS SE PRC1500i (1500 VA), also known as Powerware 5119, according to Karl Schmidt (http://lists.alioth.debian.org/pipermail/nut-upsuser/2005-July/000026.html) also Deltec PowerRite Pro II, and according to http://www.usedups.de/compaq_ups.html also Compaq R3000h. I am not sure if the information in http://www.bps.hu/powerware/model_en.html is to be interpreted as that it was

My UPS is an Exide NetUPS SE PRC1500i (1500 VA), also known as Powerware 5119, according to Karl Schmidt (http://lists.alioth.debian.org/pipermail/nut-upsuser/2005-July/000026.html) also Deltec PowerRite Pro II, and according to http://www.usedups.de/compaq_ups.html also Compaq R3000h. I am not sure if the information in http://www.bps.hu/powerware/model_en.html is to be interpreted as that it was

Hello, I got this information from the manufacturer of my ups Kobian/Mercury and were tested wtih powstatd on Linux (Works OK). Now i want to configure it with NUT and i didn't have any luck (it always says OB) Initiliasation for monitoring: RTS = 1 (High) Main power fail: CTS = 0 (Low) Batter low: DCD = 0 (Low) Kill UPS: DTR = 0 (Low) How would the ups.conf look like? Reagards, Lep

Someone might want to add this to the docs - cable list and compatibility list - took me way to long to find. I was trying to find information on my UPS and came up with the following names for the same UPS series. Powerware 5119 Exide name was NetUPS SE Deltec name was PowerRite Pro II (1000VA-3000VA) What I have: The Exide NETUPS SE model PRC2400a p/n 05144038-3904 OUTPUT 2400VA 1600 WATTS

>> On Nov 21, 2015, at 2:43 AM, R?bert SZAKSZ <robert at szaksz.eu> wrote: >> >> I mesured it and on DC and it shows 0 V (zero V). >> May be the information (pls. see attachment) that UPS PIN1 should bee keept HI is mandatory. Should I connect it to PC PIN4 DTR? > >Certainly possible. blazer_ser and nutdrv_qx should set DTR high and RTS low by default, but

> +22 = Gamatronic UPSs with alarm interface > + [CP=RTS] [OL=CTS] [LB=\-DCD] [SD=DTR] > + > +22 = CyberPower SL seriess > + [CP=RTS] [OL=CTS] [LB=\-CAR] [SD=DTR] > + > + This part of the patch is no good. While TIOCM_CAR is equivalent to TIOCM_CD (at least in some implementations) CAR certainly isn't handled the same as DCD by genericups. It won't be

[please use reply-all when responding - the list does not modify the reply-to header.] > On Nov 16, 2015, at 8:24 AM, R?bert SZAKSZ <robert at szaksz.eu> wrote: > > Hello, > > I have one UPS Infosec XP Pro 2500 RM and it works with windows sw RUPS2000. > Now I want to install this UPS as virtual server on vmware ESXi vMA - (SUSE SLES 11SP2 linux). > On this linux I

>On Nov 20, 2015, at 12:17 PM, R?bert SZAKSZ <robert at szaksz.eu> wrote: >> >> No progress has been made: >> >> cable is UPS - PC >> 6 - 3 >> 7 - 5 >> 9 - 2 >> > >Maybe pins 4 and 7 (ground) both need to be connected on the UPS side? I connected both to pin 5 >Unfortunately, I don't think there is a safe way (in software)

Hi Charles, >----- Original Message ----- >From: "Charles Lepple" <clepple at gmail.com> >To: "R?bert SZAKSZ" <robert at szaksz.eu> >Cc: nut-upsuser at lists.alioth.debian.org >Sent: Monday, November 16, 2015 3:20:17 PM >Subject: Re: [Nut-upsuser] Contact-closure UPS > >[please use reply-all when responding - the list does not modify the

Hello again, I have a Sola 305 (aka Powerware 3110) here connected via a serial INT-0051 cable which I am trying to get working with nut. The driver.list file indicates that nut supports the Sola 305 when connected via the INT-0025C cable using the genericups driver with upstype set to 7 but it does not mention the INT-0051. I was able to use the "Basic CheckUPS II" utility provided

Hello, I have a UPS connected to my server with the following: Server is Suse 10.1 Nut version is?Network UPS Tools - Generic UPS driver 1.32 (2.0.4) I installed this around 2005 and cannot remember how I installed the software. ups.conf: [sdrups] driver = genericups port = /dev/ttyS0 desc = "For Server & Backup" upstype = 9 upsd.conf: ACL all 0.0.0.0/0 ACL localhost

Hello again! I'm yet again the guy from the blazer_usb problem and the ATCL one too. This time I have a third UPS (the last one In my collection) that i'm trying to make work instead of the ATCL one since there's no driver for it on windows. This UPS is another no-brand box (actually it is a "kozumi", but that's just a rebrand), and apparently it's much more basic

+-----------------------------------------------------------------+ | | | Black APC 940-0024C Smart Signalling UPS Cable Wiring Diagram | | This information is verified and tested to be 100% correct. | | |

There should be a line-table entry for the end of the function, which appears to be missing from the dump you provided. llvm-dwarfdump should report this address with 'end_sequence' in the Flags. Are you using a different dumper? I am not sure but my guess would be that inline data is not represented in the line table. The line table's primary purpose is to inform the debugger

Hi, I have a Comapq T2400H model 242688-003 and do not have the special cable to connect it to my serial port. I have tried all sorts of cable wirings that I found on the net, including ones for the powerware 5119 which appears to be the same model. I have read the documentation that comes with NUT, tried to read the source code and looked at the genericups code too.? I have

Hello. Has anyone been able to successfully make data (dialup modem) calls through a TDM2400E? We're able to make fax and credit card calls fine, but cannot successfully make modem calls using a 56K modem connected to a patch panel connected to an FXS port which then gets bridged to an FXO port connected directly to a phone line. We have 'echocancelwhenbridged=no' set in

Hello * Trying to get above serial UPS to work gives my some troubles. With upstype=21 [CP=RTS] [OL=CTS] [LB=-DCD] [SD=RTS+DTR] and/or upstype=4 [CP=RTS] [OL=CTS] [LB=-DCD] [SD=-RTS] I do get OL OB LB ok, but shutting down the UPS does not work. Direct call w/ command genericups ... -k and from lowbatt/ initscripts doesnt do. The UPS claims to be capable of and the software shipped (RUPS2000)

I'm not familiar with the target instruction set, but if "MOV PC, R0" is not a return instruction, I'm guessing that the sequence starting at A39C is a dispatch through a jump table. The jump table would be considered part of the instruction stream and included in the scope of the line table. This is not a case where you would see end_sequence; my mistake. The line table does

Hi, Could somebody please help me get this one to work using the close contact information. I can not get it to detect off line Config: OpenSuse 11.0 NUT 2.2.2 [cyberpower] driver = genericups port = /dev/ttyS1 mfr = "Cyberpower" model = "PR1500LCDRTXL2U" desc = "Cyberpower PR1500LCDRTXL2U - Serial/contact"