similar to: Re: bcmxcp_usb "Can't open POWERWARE USB

I tried switching to the USB version of bcmxcp_usb and get this error when I try starting up upsdrvctl or bcmxcp_usb like so: /etc/nut/bcmxcp_usb -DDDD -a powerware -u nut I used this for ups.conf: [powerware] driver = bcmxcp_usb port = auto With the serial/usb dongle, I used this successfully: [powerware] driver = bcmxcp port = /dev/ttyUSB0 What devices does

Hi I'm having a problem with the bcmxcp_usb driver FSD command: everything seems to work apart from: upsmon -c fsd Environment: Ubuntu 7.04, nut 2.0.5-1, nut-usb 2.0.5-1, Powerware 3105 UPS. upsd appears to send the FSD command to the UPS, upsmon then runs my NOTIFYCMD (which halts my PC) but the UPS just doesn't turn off. Here are the /var/log/daemon.log entries: Jul 24 23:13:16

Ok, I installed the ups, and installed nut, and /proc/bus/usb/devices says this T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=06da ProdID=0002 Rev= 0.01 S: Manufacturer=POWERWARE S: Product=Powerware UPS C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr= 20mA I: If#= 0 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00

Hi everyone, First of all a big thank you for the NUT package, I've been using it for years and couldn't get by without it! I have two Powerware UPS's here, a 9120/1500va and a 5110/700va. The 9120 has used a hacked bcmxcp driver (serial) from the 2.0.2 nut version for about a year now (which I'll explain more about in a seperate email to the dev list), and the 5110 which I just

Hi Greg, Thomas and the list, I've not forgotten you nor your issue. It just took some time to gather a "faulty" unit and a bit of time to reproduce your issue. The good news is that I've commited a fix to the NUT development branch (aka Subversion), in the release r2015. The bad news is that your test and feedback is welcome ;-) For more info on getting and compiling the

I'm running Solaris 11 Express (snv_151a X86) with NUT 2.6.0 compliled from the source tarball and a Powerware 5115. I was seeing the driver hang, so gave it some '-D's (23 apparently ;-) and found that it seems to be getting into an infinite loop when reading data from the UPS. The debug output is attached and I would be very grateful for some help or advice on what to try next.

Hello, ppl! I try configure NUT for communicate with my Powerware 5115 UPS. As root I run '/lib/nut/bcmxcp_usb -DDDD -u root -a ups', but driver can't connect to my UPS. Some output: Network UPS Tools - BCMXCP UPS driver 0.10 (2.0.4) debug level is '4' usb_set_debug: Setting debugging level to 3 (on) usb_os_init: Found USB VFS at /dev/bus/usb usb_os_find_busses: Found 001

Hi Does there exist any work on getting the powerware driver to work with USB devices under freebsd? I have tryed with the usb enabled newhidups driver for freebsd but it does not seem to work. $ newhidups -a newhid -DD Network UPS Tools: New USB/HID UPS driver 0.23 (2.0.2) debug level is '2' found 0 (-1) No USB/HID UPS found //erlis -------------- next part -------------- An HTML

Hi, I recently downgraded my kernel to 2.4 series (2.4.32-rc2). Now I can't get nut running. It was fine with 2.6.14. It say's: --------------------- # ./bcmxcp_usb -uroot AUTO Network UPS Tools - BCMXCP UPS driver 0.10 (2.1.0) Can't reset POWERWARE USB endpoint Unable to find POWERWARE UPS device on USB bus ... --------------------- I've straced it in nut_usb.c

Dear Nutters, I am trying to get NUT as supplied with SuSE 10.1 working and I think I have a USB problem, possibly due to some missing startup scripts concerning permissions. The machine sees the USB device as per /var/log/messages: Jun 5 16:28:27 silver-server kernel: usb 2-1: new low speed USB device using uhci_hcd and address 7 Jun 5 16:28:27 silver-server kernel: usb 2-1: new device

Hi, I have set up a RaspberryPi computer to do monitoring of two UPSs. One is an MGE evolution 800, one is an Eaton Powerware 5110. The MGE was being monitored by another Linux (Ubuntu 12.04) computer, and I just copied and pasted in the relevant nut config and it works just fine with nut. I've tried to set up the Powerware 5110 with nut, and the bcmxcp_usb driver can't communicate

Hi, I have got a Powerware 5110 UPS which has a usb interface on it. I have downloaded and compiled nut-2.0.3-pre2 with the usb drivers enabled on RedHat Enterprise V3 however I have been unable to get nut to connect to the UPS. I have tried executing the driver directly (using bcmxcp_usb -DD -u root /proc/bus/usb/002/002) as well as using upsdrvctl with the port set to auto (am I correct in

Hi, I'm having a hard time configuring a Mustek Powermust 600VA ups to work via USB with nut. I read somewhere that nut works OK via the rs232 cable, but unfortunately I don't have a COM port in my computer. The kernel detects the ups as an Xbox pad :) and loads the xpad module. I tried running /lib/nut/megatec with different /dev/ttySx but it displays megatec protocol UPS was not

2009/8/28 Thomas Zulliger <Thomas.Zulliger at quiksilver.com.au> > Hi Arnaud > Hi Thomas, > I'm experiencing exactly the same problem > > DNS-323 fun_plug Fonz > nut 2.4.1-1.tgz > powerware 3105 > using BCMXCP_usb > > /mnt/HD_a2/packages # lsusb > Bus 002 Device 001: ID 0000:0000 > Bus 001 Device 002: ID 0592:0002 Powerware Corp. > Bus 001

Hi, I'm trying to get a Powerware 3105 UPS working on SuSE 10.0. I have compiled nut from the current Subversion repository. This UPS uses the bcmxcp_usb driver. I cannot get the driver to find the ups on the USB bus. The error message I get is:- -------------- bcmxcp_usb -u nut -DDDDD -a pw3105 -------------------- Network UPS Tools - BCMXCP UPS driver 0.10 (2.1.0) debug level is

THE GOOD: NUT is able to communicate with my Powerware 5115A over USB using the bcmxcp_usb driver: ambient.temperature: 38 battery.charge: 99 battery.runtime: 9000 battery.voltage: 27.07 driver.name: bcmxcp_usb driver.parameter.pollinterval: 2 driver.parameter.port: auto driver.version: 2.2.1 driver.version.internal: 0.13 input.frequency: 50.34 input.voltage: 235 output.current: 0.0

Good evening, I tried getting this to work a couple years back but didn't have enough time to do all the debugging that was needed (apologies to the devs who tried to help at that time). It's working much better now, but I'm still not able to get an answer from upsc. Can anyone help me work out why I'm getting the error when querying with upsc: Error: Data stale My

Good evening, I tried getting this to work a couple years back but didn't have enough time to do all the debugging that was needed (apologies to the devs who tried to help at that time). It's working much better now, but I'm still not able to get an answer from upsc. Can anyone help me work out why I'm getting the error when querying with upsc: Error: Data stale My

I've got some strange problem with NUT on my 5115 on Debian Etch: ---snip--- $ sudo ./bcmxcp_usb -DDDDDDD -a 5115 Network UPS Tools - BCMXCP UPS driver 0.13 (2.3.0-1181) Warning: This is an experimental driver. Some features may not function correctly. debug level is '7' Can't set POWERWARE USB configuration Unable to find POWERWARE UPS device on USB bus Things to try: -

I can't seem to get NUT to connect to my new PowerWare (Eaton) 5115. (Linux 2.6.34.1 x86_64, Gentoo) # /etc/init.d/upsdrv start * Caching service dependencies ... [ ok ] * Starting UPS drivers ... Network UPS Tools - UPS driver controller 2.4.3 Network UPS Tools - BCMXCP UPS driver 0.23 (2.4.3) USB communication subdriver 0.18