similar to: RE Powerware 5115 and USB

Hi, I am wanting to use NUT to connect to an Eaton Powerware 5110 UPS using USB to connect. - I am using NUT 2.0.2 - I have compiled it with USB support - I can see that the UPS is registered as connecting in /var/log/messages eg usb 3-1: USB disconnect, address 3 usb 3-2: new low speed USB device using uhci_hcd and address 4 But I don't know how to progress from here.

Ok, I installed the ups, and installed nut, and /proc/bus/usb/devices says this T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=06da ProdID=0002 Rev= 0.01 S: Manufacturer=POWERWARE S: Product=Powerware UPS C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr= 20mA I: If#= 0 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00

Hi, I'm trying to get a Powerware 3105 UPS working on SuSE 10.0. I have compiled nut from the current Subversion repository. This UPS uses the bcmxcp_usb driver. I cannot get the driver to find the ups on the USB bus. The error message I get is:- -------------- bcmxcp_usb -u nut -DDDDD -a pw3105 -------------------- Network UPS Tools - BCMXCP UPS driver 0.10 (2.1.0) debug level is

Hi Does there exist any work on getting the powerware driver to work with USB devices under freebsd? I have tryed with the usb enabled newhidups driver for freebsd but it does not seem to work. $ newhidups -a newhid -DD Network UPS Tools: New USB/HID UPS driver 0.23 (2.0.2) debug level is '2' found 0 (-1) No USB/HID UPS found //erlis -------------- next part -------------- An HTML

Hi everyone, Been searching like crazy to find an answer to this. I have even read some of the source code but cannot figure this one out. I have installed nut 2.4.1 on my QNAP 409 Pro. (command: ipkg install nut) I have configured the ups.conf, upsd.conf and upsd.users. When i run "upsdrvctl start" I get the following error messages and output.

Hello. I've tried to configure Windows (complete port, Beta): Windows MSI installer 2.6.0-1 with my Powerware 5115 connected via USB port but have no luck. Here is my config files: *nut.conf:* MODE = netserver *ups.conf:* [PW5115] driver = bcmxcp_usb port = notUsed desc = "PowerWare 5115" *upsd.conf:* LISTEN 192.168.1.12 3493 *upsd.users:* [monuser]

Hi Arnaud, Any luck with the latest subversion trunk? From: Greg Sent: Wednesday, May 13, 2009 10:34 PM To: Greg ; Arnaud Quette Cc: Kjell Claesson ; nut-upsuser at lists.alioth.debian.org Subject: Re: [Nut-upsuser] Nut and PowerWare 5115 Hi Arnaud, Some more testing on Ubuntu 9.04. Here is the output of bcmxcp_usb and lsusb ============================================ root at

I have an FC5 system with a powerware 5110 usb ups. The system seems to find the UPS ------------------------------ [root@b1 src]# lsusb Bus 004 Device 001: ID 0000:0000 Bus 003 Device 002: ID 0592:0002 Powerware Corp. Bus 003 Device 001: ID 0000:0000 Bus 002 Device 001: ID 0000:0000 Bus 005 Device 001: ID 0000:0000 Bus 001 Device 001: ID 0000:0000 ------------------------------- [root@b1

I am seeing some problems when using the Powerware 5115 UPS when connected to the Patsburg USB controller and would like to know if anyone has a solution. The symptom is that PING messages sent to the bcmxcp_usb driver take as long as 25 seconds to complete. The configuration is a Romley patform (a.k.a., Sandy Bridge + Patsburg) running Debian 6 with 2.6.39 kernel with NUT 2.6.4 in which the

I've got some strange problem with NUT on my 5115 on Debian Etch: ---snip--- $ sudo ./bcmxcp_usb -DDDDDDD -a 5115 Network UPS Tools - BCMXCP UPS driver 0.13 (2.3.0-1181) Warning: This is an experimental driver. Some features may not function correctly. debug level is '7' Can't set POWERWARE USB configuration Unable to find POWERWARE UPS device on USB bus Things to try: -

Hi, I'm trying to get a Powerware 5115 to communicate with the NUT via USB under Debian Linux and need help. Here is the output that I see. co-nh5:/tmp/mnt/projects/pwusb/nut-2.4.1# /usr/local/ups/bin/upsdrvctl -u root start Network UPS Tools - UPS driver controller 2.4.1 Network UPS Tools - BCMXCP UPS driver 0.21 (2.4.1) USB communication subdriver 0.17 Communications with UPS lost:

I tried switching to the USB version of bcmxcp_usb and get this error when I try starting up upsdrvctl or bcmxcp_usb like so: /etc/nut/bcmxcp_usb -DDDD -a powerware -u nut I used this for ups.conf: [powerware] driver = bcmxcp_usb port = auto With the serial/usb dongle, I used this successfully: [powerware] driver = bcmxcp port = /dev/ttyUSB0 What devices does

Hello, ppl! I try configure NUT for communicate with my Powerware 5115 UPS. As root I run '/lib/nut/bcmxcp_usb -DDDD -u root -a ups', but driver can't connect to my UPS. Some output: Network UPS Tools - BCMXCP UPS driver 0.10 (2.0.4) debug level is '4' usb_set_debug: Setting debugging level to 3 (on) usb_os_init: Found USB VFS at /dev/bus/usb usb_os_find_busses: Found 001

Hi everyone, First of all a big thank you for the NUT package, I've been using it for years and couldn't get by without it! I have two Powerware UPS's here, a 9120/1500va and a 5110/700va. The 9120 has used a hacked bcmxcp driver (serial) from the 2.0.2 nut version for about a year now (which I'll explain more about in a seperate email to the dev list), and the 5110 which I just

Kjell Claesson wrote: > Then i have a problem. My computer is down due to a > faulty mainboard, Youch. I hate it when that heppens. Hope it wasn't because you got a power spike ;-) Let me or Georg know if you want us to run any debug code. Feels like a bcmxcp_usb driver bug to me since the bcmcxp serial driver works fine and all my other USB devices work fine (wifi adapter, memory

2009/8/28 Thomas Zulliger <Thomas.Zulliger at quiksilver.com.au> > Hi Arnaud > Hi Thomas, > I'm experiencing exactly the same problem > > DNS-323 fun_plug Fonz > nut 2.4.1-1.tgz > powerware 3105 > using BCMXCP_usb > > /mnt/HD_a2/packages # lsusb > Bus 002 Device 001: ID 0000:0000 > Bus 001 Device 002: ID 0592:0002 Powerware Corp. > Bus 001

THE GOOD: NUT is able to communicate with my Powerware 5115A over USB using the bcmxcp_usb driver: ambient.temperature: 38 battery.charge: 99 battery.runtime: 9000 battery.voltage: 27.07 driver.name: bcmxcp_usb driver.parameter.pollinterval: 2 driver.parameter.port: auto driver.version: 2.2.1 driver.version.internal: 0.13 input.frequency: 50.34 input.voltage: 235 output.current: 0.0

Hi. I'm looking for a way to configure an Eaton Powerware 5125 under Debian Squeeze (amd64) with USB port. Can someone help me? Find attached bellow my settings: # cat /etc/nut/ups.conf ... [ups01] driver = bcmxcp_usb port = /dev/bus/usb/002/003 desc = "Powerware 5125" # ls -la /dev/bus/usb/002/003 crw-rw-r-- 1 root nut 189, 130 Nov 21 11:45 /dev/bus/usb/002/003 #

Hi, I have an UPS Powerware 5110 ( usb connection ), on Linux OS is Debian 4.0 The /etc/ups.conf file setting is: [myups] driver = bcmxcp_usb port = auto desc = "UPS Powerware 5110 1500 VA" When the daemon starts it displays the following message: "Starting Network UPS Tools: (upsdrvctl failed)." Looking at /var/log/syslog I found the following line

Hi I'm having a problem with the bcmxcp_usb driver FSD command: everything seems to work apart from: upsmon -c fsd Environment: Ubuntu 7.04, nut 2.0.5-1, nut-usb 2.0.5-1, Powerware 3105 UPS. upsd appears to send the FSD command to the UPS, upsmon then runs my NOTIFYCMD (which halts my PC) but the UPS just doesn't turn off. Here are the /var/log/daemon.log entries: Jul 24 23:13:16