Displaying 20 results from an estimated 700 matches similar to: "OMNIVS1500XL and FreeBSD"
2009 Sep 05
1
FreeBSD, NUT OmniVS1500
Howdy,
I had this working with lots of help for a developer before (Charles Lepple),
but after upgrading to a somewhat more current version of FreeBSD the
patched-up version stopped working. Seeing as this was more than a few years
ago, I thought I'd give a new libusb and NUT a try to see if it might work out
of the box. So far, no luck.
Some info:
FreeBSD 6.3
libusb 0.1.12
NUT 2.4.1
2007 Sep 21
2
TrippLite 1500XL problems, continued.
So a month or more ago, I posted about continual disconnect messages from
this UPS (roughly 2/hour), using nut 2.2.0 on debian etch. Now, I've
finally gotten around to running tripplite_usb in debug mode, and these
are the results:
...
send_cmd(msg_len=2, type='L')
send_cmd(msg_len=2, type='S')
send_cmd(msg_len=2, type='B')
send_cmd(msg_len=2, type='L')
2009 Nov 08
1
Tripplite INTERNETX525
Hi,
I'm running the latest version of NUT and with the above UPS and I
keep getting the following error:
"tripplite_usb[3308]: Error reading B value: Device detached? (error
0: could not claim interface 0: Device or resource busy)"
The device keeps disconnecting and re-connecting until fails. I've
tried to see if others are getting this - but I could not locate a
2007 May 11
11
tripp lite smart2200RMXL2U error reading protocol
I'm working on a gentoo server with Nut 2.0.5-r1 and libusb-0.1.12.
I originally tried the hidups driver which seemed to work, but produced
a large amount of unhandled events. Then I tried the newhidups which
told me my ups wasn't supported. When I try using
tripplite_usb -u root -DDDD /proc/bus/usb/002/002
I get that there isn't a match. But when I try using
tripplite_usb -DDDD
2010 Jan 10
1
Eaton PW5110 + nut-2.4.1 + OpenBSD
Hello,
I 'm trying to set up an Eaton PW5110 using nut-2.4.1 in OpenBSD, my
ups.conf follows :
[myups]
driver = bcmxcp_usb
port = auto
desc = "Eaton PW 5110 (1500VA)"
My first attempt to run upsdrvctl ended up complaining about unimplemented
usb_clear_halt() in libusb. I patched libusb-0.1.12 with the following
patch :
2006 Jan 13
1
help with TRIPP LITE SMART550USB
Hi
I have a Tripp lite smartusb550 using fedora 3 (2.6.12-1.1381_FC3smp).
Managed to establish communication with the ups using the tripplite_usb
driver
but get the following errors
Any help to make it work will be appreciated
cheers
Julio
-----------------------------------------------------------------------------------------------------------------------------------------------------
2014 Jun 26
1
The dreaded Tripp Lite SMART500RT1U and NUT
<nut-upsuser at lists.alioth.debian.org>
I am doing my best to avoid have to spend $280 for a network monitoring
card to put into a $190 UPS just to have some good remote monitoring
capabilities. Rather, I would like to monitor my many 1U Tripp Lite's on
my network using a Raspberry Pi running Raspian and using NUT.
However, I cannot seem to get it working. And I while the hardware
2014 Jun 27
3
The dreaded Tripp Lite SMART500RT1U and NUT
Hello Charles,
Thanks for the feedback. I will try to answer some of these questions:
> 09AE/0001 is essentially a USB-to-serial converter, and is not
> compatible with usbhid-ups. (Theoretically, we could have a companion
> driver that talks the same protocols over a real RS-232 port, but the
> hardware I used to develop the tripplite_usb driver only has a USB
> port.)
Ah, that
2008 Sep 26
0
FreeBSD usbhid-ups problem
Citeren "Daniel O'Connor" <doconnor at gsoft.com.au>:
> usb_control_msg: 161 1 769 0 0x813310c 2 4000
> USB error: error sending control message: Input/output error
> Can't retrieve Report 1: Input/output error
> upsdrv_updateinfo...
> Got to reconnect!
>
> usb_set_debug: Setting debugging level to 3 (on)
> usb_os_find_busses: Found /dev/usb0
>
2006 Jun 27
1
Tripp Lite OMNIVS1500XL Unknown protocol
Good afternoon,
I'm trying without much success to monitor a Tripp Lite OMNIVS1500XL
using NUT. I checked the compatibility list and saw that this UPS is
supported by tripplite_usb.
The system is running Debian Stable, but I've downloaded NUT 2.0.3 and
compiled from source since the packaged 2.0.1 doesn't include tripplite_usb.
I compiled --with-user=nut.
My first attempt at
2014 Jun 29
1
The dreaded Tripp Lite SMART500RT1U and NUT
Hello Charles,
I think we are making progress! I grabbed nut using git, and applied
your patch without any problems. Getting to the point that I could
run a configure on my RPi - was something else. I found this blog
post, which was very helpful (for anyone else that may try it):
http://atelier-orchard.blogspot.com/2013/11/raspberry-pixf86-video-fbdev.html
It's not in English, but you get
2008 Jan 23
1
empty ups.status on TrippLite SMART1500RMXL2U
Hello,
I have a TrippLite SMART1500RMXL2U that I'm trying to get running with
Nut 2.2.1.
Running upsdrvctl start works, upsd works, but upsc has "issues":
je-nas:~/src/nut-2.2.1# upsdrvctl start
Network UPS Tools - UPS driver controller 2.2.1-
Network UPS Tools - Tripp Lite OMNIVS and SMARTPRO driver 0.11 (2.2.1-)
Warning: This is an experimental driver.
Some features may not
2010 Jan 31
3
smart1050slt by tripp lite
Original Message
>I have 2 SmartUOS1050SLT's that apparently protocol 3004, has there
>been
>any progress on getting these units supported under nut? I am running
>version 2.4.1, and get the following output when starting the driver.
>#lsusb
>Bus 005 Device 002: ID 09ae:0001 Tripp Lite
># upsdrvctl -DDDD start
>Network UPS Tools - UPS driver controller 2.4.1
2016 May 26
2
Tripplite SMART2200VS with tripplite_usb: UPS doesn't shut down
>
> > 2.117586 send_cmd(msg_len=2, type='G')
> > 3.219418 libusb_get_interrupt: Connection timed out
> > 3.219474 libusb_get_interrupt() returned 0 instead of 8 while
> sending 3a 47 b8 0d 00 00 00 00 '.G......'
> > 4.219593 libusb_get_interrupt: Connection timed out
> > 4.219661 libusb_get_interrupt() returned
2012 Dec 07
2
Tripp Lite SMART1000RM2U
Hi,
I recently purchased a Tripp Lite SMART1000RM2U UPS
(http://www.tripplite.com/en/products/model.cfm?txtSeriesID=744&txtModelID=2657)
and tried to configure the NUT with tripplite_usb driver and encounter
the following problems:
1. battery.charge doesn't report correct charge level when the UPS is
On Batter. It just reports 0. Even though it will report 100 when on
line power.
2. I
2016 May 25
2
Tripplite SMART2200VS with tripplite_usb: UPS doesn't shut down
Please ignore the previous message as I sent it before it was complete.
Hello,
I have a Tripplite SMART2200VS that isn't being shut down when the nut
master asks it to. My initial test was simply upsmon -c fsd which did
cause the system to shut down, however the UPS remained on and providing
power to its loads. Looking in the logs (daemon and syslog) it was not
clear to me that NUT was
2014 Jun 28
0
The dreaded Tripp Lite SMART500RT1U and NUT
On Thu, Jun 26, 2014 at 10:20 PM, Steve Ballantyne
<steve.ballantyne at gmail.com> wrote:
>> However, we don't have all of the 09AE/0001 protocols decoded in the
>> tripplite_usb driver.
>
> I can try to help out on this front? :-)
Definitely.
>> > 9.783126 Unknown input voltage range: 0x02
>> > 9.783308 Unknown number of switchable
2015 Jan 06
2
libusb drops connection to my Tripp Lite SMART500T1U
Hey Charles,
Many months ago you assisted me in making some code changes to get my
Tripp Lite up and running. Thank you for that. Those changes you
committed to the repository work very well. I just built a new image
for a Raspberry Pi running the latest Raspbian OS and the latest
nut-master.
I have everything working ... except I seem to be losing my device
periodically. So if I enable my
2005 Aug 06
1
tripp lite omnivs1500xl and usb
i just purchased a tripp lite OMNIVS1500XL and have been attempting to get
it working with the usb drivers since it doesn't have a serial port. it
hasn't been anywhere near successful and i was hoping someone might be
able to point me in the right direction.
i run gentoo and this is what i currenlty have installed:
nut 2.0.2
libusb 0.1.10a (gentoo modified)
usbutils 0.11-r5
2007 Mar 24
0
Some FreeBSD tips (was: OMNIVS1500XL and FreeBSD)
Hello all,
I just wanted to dump some info here for the archives.
Here's the original thread for reference:
http://lists.alioth.debian.org/pipermail/nut-upsuser/2007-March/002403.html
Charles Lepple did a tremendous amount of work to get my TrippLite USB
working on FreeBSD 6.2. I'm running an svn version (nut-2.1.0-r879) to
pick up his changes to tripplite_usb. So far, it is