similar to: Belkin F6C1100-UNV

I just bought a pair of Belkin USB UPSes -- F6C1200-UNV and F6C550-AVR -- and installed the latest version of nut under Ubuntu 7.04. I'm using the F6C1200-UNV. My system does see the device; dmesg says [ 82.718428] usb 2-2: new low speed USB device using ohci_hcd and address 2 [ 82.941189] usb 2-2: configuration #1 chosen from 1 choice [ 83.036825] usbcore: registered new driver

I just bought a pair of Belkin USB UPSes -- F6C1200-UNV and F6C550-AVR -- and installed the latest version of nut under Ubuntu 7.04. I'm using the F6C1200-UNV. My system does see the device; dmesg says [ 82.718428] usb 2-2: new low speed USB device using ohci_hcd and address 2 [ 82.941189] usb 2-2: configuration #1 chosen from 1 choice [ 83.036825] usbcore: registered new driver

Hello, all, I had been using NUT's Ubuntu package (64 bit) with no problems until upgrading to Ubuntu 11.04. Now, I get the following message when I try usbhid-ups: $ sudo /lib/nut/usbhid-ups -a mybelkin Network UPS Tools - Generic HID driver 0.35 (2.6.0) USB communication driver 0.31 Can't claim USB device [050d:1100]: could not detach kernel driver from interface 0: Operation not

All, I just bought a Belkin F6C1100-UNV and am trying to get it to work with NUT. I have tried many drivers ( "belkin", "belkinunv", "genericups upstype=4", and "genericups upstype=7", "bestups", "fentonups"). None of them seem to work. Does anyone have any experience with this device? If there is some utility that you all use to

Belkin F6C1200-UNV on Ubuntu 7.04, megatec_usb driver, Every few minutes I get a beep and a "UPS not available" message that seems to be bogus; upsc reports real data, not at complaint that it's stale. Is there some timeout I need to lengthen? Also, shouldn't upsc report the poll time associated with the data it displays? -- >>esr>>

Hi everyone, I have a belkin ups that was bought around 2 months ago. It seems like the driver doesn't like the UPS, although on the website it's listed as supported. This is on a gentoo system with nut 2.2.1 . megatec_usb output: ---------SNIP---------- digamma nut # ./megatec_usb -a belkinm -DDDDDD Network UPS Tools 2.2.1 - Megatec protocol driver 1.5.9 [megatec_usb] Carlos Rodrigues

Oh oops, I see you already did. -- Peter selinger wrote: > > You could send it without "submitting" it. That's the advantage of > patches - they can be discussed. There are lots of eyeballs here that > might see what's wrong. Thanks, -- Peter > > Eric S. Raymond wrote: > > > > Peter Selinger <selinger at mathstat.dal.ca>: > > > I

Hi. My Belkin UPS F6C1100-UNV works fine with megatec_usb version 1.6 (2.4.1). However, it doesn't work with 2.4.2 nor 2.4.3. # /lib/nut/megatec_usb_old -D -a belkin Network UPS Tools - Megatec protocol driver 1.6 (2.4.1) Serial-over-USB transport layer 0.10 debug level is '1' Starting UPS detection process... 0 out of 5 detection attempts failed (minimum failures: 2). Cancelling

I'm trying to set up a belkin f6c1100-unv UPS to work with nuts. From reading the mailing list, it sounds like the belkinunv serial driver should work and that the USB driver is potentially troublesome. Is this a correct impression? Also I may have missed this but if I do go with the serial (or USB port) is there any simple command line method for verifying basic connectivity? The

I have a new Belkin F6C900-UNV. I see that it's not listed in belkin-hid.c The VendorID is 0x050d like all the Belkin UPSes, and the ProductID is 0x0900. I haven't had a chance to actually test the development version of nut yet, since I'm running Fedora Core 6, which still has nut 2.0.3. `newhidups -DD -a myups` gives the error of: Checking device (050D/0900) (001/002) - VendorID:

Mr. Selinger, I'm CCing you directly since it appears (insofar as I can tell) that you are one of the delelopers for the newhidups driver. This is the third time I've submitted this (hence the CC this time). Hopefully mailman takes it. I've tweaked my SPF records, and I'm hoping that was the problem. My sincere apologies if this has gone through and I just haven't seen it

Hi, I've been fighting with trying to get a Belkin Universal model F6C800-UNV to work with NUT. The error I am getting is as follows: ---------------------------------------------- * Starting UPS drivers ... Network UPS Tools - UPS driver controller 2.0.0 Network UPS Tools - Belkin 'Universal UPS' driver 0.06 (2.0.0) tcgetattr(/dev/ups): Inappropriate ioctl for device Driver failed

I just moved my UPS over from serial to USB and found that I needed to add it to the hotplug USB list to make things work. Belkin F6C120-UNV - Bus 002 Device 004: ID 050d:0912 Belkin Components It seems to be working OK on 2.0.4 with newhidups. Attached is a patch which I think should add the appropriate device id's in the right places to the trunk code. Jon -------------- next part

Greetings! Thanks to all the developers who have made this project so far. Searching for a Linux based Belkin UPS monitor led me straight to the Network UPS Tools. I have bought a Belkin F6C900-UNV (900VA) for use on a Slackware 10.2 server to replace an older APC model that died suddenly. So far I have successfully managed to get NUT 2.0.5 compiled and configured and found that this Belkin

Hi, I bought a Belkin Active Battery Backup UPS (http://www.belkin.com/uk/activebattery/) yesterday with a USB port and hoped it would work with nut. The device will show up in /proc/bus/usb/devices as a Cypress Semiconductor USB to Serial. It creates /dev/hiddev0 (and this disappears when the UPS is unplugged). I've tried using belkin, belkinunv, usbhid-ups and megatec_usb. I've tried

# /lib/nut/megatec_usb -a myups Network UPS Tools 2.2.0- - Megatec protocol driver 1.5.4 [megatec_usb] Carlos Rodrigues (c) 2003-2007 Serial-over-USB transport layer for Megatec protocol driver [megatec_usb] No supported devices found. Please check your device availability with 'lsusb' and make sure you have an up-to-date version of NUT. If this does not help, try running the driver with

A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 188 bytes Desc: not available Url : http://lists.alioth.debian.org/pipermail/nut-upsdev/attachments/20071124/3ceb35d2/attachment.pgp

I recently bought a Belkin F6H375 UPS. It connects to the computer via USB. Searching the Internet led me to believe that the megatec_usb driver in nut supports this UPS, however I've been unable to get it to work. I have this in ups.conf: [belkinusb] driver = megatec_usb port = auto desc = "Belkin USB" Here's what happens when I try to use it: ~ #

For the record, I was able to get the following working: Device: Belkin F6C1500-TW-RK Driver: belkin I tried the "belkinunv", which I use for my F6C1100-UNV, but it didn't work. At least there was a driver that worked! :-) Feel free to add it to the list of "tested" configs. Thanks, Dave ---------------------------------------------------------- Are Your Friends

I recently installed NUT 2.2.1 and set it up with a Belkin F6C100-UNV. I can monitor it via serial (belkinunv) or USB (usbhid-ups) cable, and both do seem to work fine, but I would prefer USB to avoid having to add a PCI serial card to the machine. I had to unplug something else to try it with a serial cable. Using 'belkinunv', there's a "-x wait" option: [ from