similar to: OT: snmp get data from windows controlled UPS

hi @ all, i just wonder, if it is posible to read the values for all the three phases of a mge galaxy 6000 ups? we have unfortunately one mge comet ups (one phase) to play at work, but it is important to know, how many information upsc can deliver from a galaxy. we plane to use web / snmp interface. can someone post the upsc from such ups? thanks in advance, miroslav -- SHALTEV.ORG

Hello, I have a MGE Comet S31. I installed nut for Debian/Sarge and configured the mge-utalk protocol. I get the following syslog messages Sep 28 11:10:41 neckarsulm upsmon[25505]: Poll UPS [comet@mastermind] failed - Variable not supported by UPS Sep 28 11:10:46 neckarsulm mge-utalk[25284]: updateinfo: Cannot update ups.temperature Sep 28 11:10:46 neckarsulm mge-utalk[25284]: updateinfo: Cannot

Hi, I just got at work an MGE UPS Comet EX RT 7 and I can communicate fine with it through mge-shut, it detects correctly when on battery. I am using Nut 2.0.3 on Linux (RHEL 3). I am trying to simulate a low battery condition to test my shutdown procedure by setting lowbatt to 98%: driver.parameter.lowbatt: 98 but the ups reaches this value, goes to 97% and still no LB. I tried to change,

I'm trying to set up nut with a MGE UPS equiupped with a network management card, but encountered a problem. UPS: MGE Pulsar M 3000 Network Management card (installed in the UPS): 66102 (2006 edition) Operating system: FreeBSD Nut port version: 2.0.5 Nut driver: snmp-ups According to MGE in Norway this card is supported by nut, but only the old version of the card (66244) is listed on

Hi everyone, We just got an MGE Comet EX 11 RT with extra battery (all 250kg of it..) and I have talked to it with NUT. One thing I see is the frequency.. input.frequency: 500 output.frequency: 500 It appears to be in tenths of a Hz vs Hz as I see on a Pulsar Extreme. I'm using NUT 2.0.3 on FreeBSD 6.1 Thanks. -- Daniel O'Connor software and network engineer for Genesis Software -

hi @ all, i use nut with mge comet ex 7 rt (mge-shut driver). Is ist possible, that upsmon loses states? I obtain onbatt and online messages every time, but sometimes there are no lowbatt and/or shutdown messages. regrads, miroslav -- SHALTEV.ORG @ http://www.shaltev.de

Hi, Our research group is planning to buy an MGE Pulsar Evolution 3000 to protect our operational computers against power failures with an SNMP network management card. We would like to connect the UPS only through its network card (and not via USB or serial cable to another computer) and install the NUT software (client+server) on each machine to catch the shutdown SNMP signal from the UPS

Hello Kim, First, I've forwarded your mail to the nut user mailing list. Thanks to register there (https://alioth.debian.org/mail/?group_id=30602) and we'll follow on the thread on it. > Terribly sorry to bother you, but I was hoping to get nut to work with > our Symmetra, which uses SNMP. nut-2.0.2 built fine on my Solaris 8 box, > but when I do "make build-snmp" it

I have been working with NUT to get this working since upgrading to a web snmp card in a UPS. I keep getting seg faults when running snmp-ups also. Below is the output. kernel: [1365065.178230] snmp-ups[1940]: segfault at 0 ip b7555470 sp bf8d89e8 error 4 in libc-2.18.so[b74c2000+1a9000] Running: Arch i686 current Nut is current git Device is Tripp Lite SU2200XLa with WEBSNMPCARD running

Hi, ? have a necron snmp ups. nut-scanner cant find it. i tried to add with these definition but it fails.. [test5-ups] driver = snmp-ups port = 10.9.40.19 community = asdf12 desc ="test" i run driver with debugging , result is , root at upsviewer-debian:/usr/local/ups/bin# ./snmp-ups -DDDDDDD -a test5-upsNetwork UPS Tools - Generic SNMP UPS driver 0.68 (2.6.5) 0.000000

fellows, I'm working on integrating the preliminary HAL support, and thought a bit about the default configure values below: --with-snmp build and install SNMP drivers (no) --with-usb build and install USB drivers (no) [ --with-hal build and install HAL support (no) ] I wonder if some auto detection magic (if the requirement is present enable the

Hello All ! Recently I have upgraded NUT to 2.4.1, and now I can't monitor old IMV LanPro S3 UPS with old SNMP board. Previously it is monitored OK, but now snmp-ups refuses to start: [root at perforce /usr/local/etc/nut]# /usr/local/libexec/nut/snmp-ups -a lanproups -DDDDDDD Network UPS Tools - Generic SNMP UPS driver 0.44 (2.4.1) debug level is '7' SNMP UPS driver : entering

Hello, i'm trying to monitor a APC Smart-UPS 1000 behind a APC AP9630 Network Management Card via SNMPv3 using the AES Privacy Protocol. * OS name and version: Debian 10.1 * exact NUT version: 2.7.4 * NUT installation method: from debian package 2.7.4-8 * exact device name and related information * Model Number AP9630 * Hardware Revision 08 * Manufacture Date

Hi, ? have a necron snmp ups. nut-scanner cant find it. i tried to add with these definition but it fails.. [test5-ups] driver = snmp-ups port = 10.9.40.19 community = asdf12 desc ="test" i run driver with debugging , result is , root at upsviewer-debian:/usr/local/ups/bin# ./snmp-ups -DDDDDDD -a test5-upsNetwork UPS Tools - Generic SNMP UPS driver 0.68 (2.6.5) 0.000000

Thanks for the quick response Charles! I may not have gotten the correct output from the snmpwalk, let me know if the attachment is usable. Thanks! New data added, here is the gdb output: Reading symbols from /usr/bin/snmp-ups...(no debugging symbols found)...done. (gdb) run -a tripplite -DD Starting program: /usr/bin/snmp-ups -a tripplite -DD warning: Could not load shared library symbols for

On 2/24/2014 11:10 PM, Charles Lepple wrote: > On Feb 24, 2014, at 10:29 PM, Jason R Begley wrote: > >> Thanks for the quick response Charles! I may not have gotten the correct output from the snmpwalk, let me know if the attachment is usable. Thanks! > Sorry, it's basically all comments. Do you have the stdout from the subdriver script? Also, how is the MIB file installed?

Hi, Nut-upsusers, I am having problem configuring NUT to work with Tripplite UPS through SNMP. There is a Tripplite SmartOnline SU10KRT3/1X and attempts to monitor it using NUT though SNMP are failing... OS: Enterprise Linux 6, Nut version: 2.6.5. ups.conf is configured: [trippliteups] driver = snmp-ups port = 10.200.254.39 desc = "ProductionServer"

Hi Stuart, Charles and the list, 2015-03-29 14:17 GMT+02:00 Stuart Henderson <stu at spacehopper.org>: > On 2015/03/28 20:02, Charles Lepple wrote: > > On Mar 25, 2015, at 9:21 PM, Stuart Henderson <stu at spacehopper.org> > wrote: > > > > > Hi, the diff inline below adds a new subdriver for snmp-ups to support > > > Huawei UPS, based on an

Hello, we have a MGE Pulsar Evolution 800 connected to a Fedora Core5 Server using a serial cable. Installed and configured properly are RPM versions of nut-2.0.3-0.1.fc5 nut-client-2.0.3-0.1.fc5 nut-cgi-2.0.3-0.1.fc5 which all work (mostly) fine. The server is connected to outlet.0 and properly shuts down when it's loosing power after around 20 minutes. It also boots up whenever the ups

On 2015/03/28 20:02, Charles Lepple wrote: > On Mar 25, 2015, at 9:21 PM, Stuart Henderson <stu at spacehopper.org> wrote: > > > Hi, the diff inline below adds a new subdriver for snmp-ups to support > > Huawei UPS, based on an observed walk from a UPS5000-E with a few bits > > filled in from the MIBs (copy at http://junkpile.org/HUAWEI_UPS_MIB/). > > Sample