similar to: Intel DG965RYCK with CentOS 5

hi! raid 1 arrays: I already have 2 systems running this same raid1 config. 1 sys has 2 120 gb 1 sys has 1 120gb and 1 200gb but matching the raid partitions this system here that is giving me fits right now has 1 250gb and 1 200gb. I tried it w/a new 250 gb for the 2nd drive but the same results. Will not boot. in druid, when I am config. the raid arrays, I always create the boot partitions

hello again, i've reported a problem with the intel scb2 ata board and syslinux a few days ago. now i've more details: the scb2 ata board has an onboard promise raid controller. when the option bios of this ide raid controller is disabled syslinux works fine - but if the option bios is enabled (which has to be if i want to boot form the harddisk) the boot of the fails (kernel version:

I have a Lenovo laptop where I recently replaced the harddisk with a Intel 530 240 Gb SSD (SATA III) on which I then installed Centos 6.5 which runs just fine albeit at SATA II speed. I then replaced the DVD-drive in the Ultrabay with an identical Intel SSD, the Ultrabay-adapter apparently uses a PATA-SATA bridge so this drive would only run at PATA speed. Being a Centos newbie, I am not

On 7/27/2015 12:29 PM, g wrote: > > On 07/27/15 10:06, Bowie Bailey wrote: >> I have an old computer running CentOS 5. I need to add an SATA drive to >> it, but it doesn't have any ports, so I need an add-on card. The board >> only has a 32-bit PCI slot. Any recommendations on cards/brands that >> work well with CentOS? I don't need any raid capabilities,

I used google but did not come up with anything current to solve my problem. I have not tried any other search engines yet. There is not a search for the CentOS list so I am creating a new post. I have tested the CentOS 5.2 and RHEL 5.3 CD's and they passed. I had to use linux mediacheck ide=nodma to get them to pass. The newest releases seem to most times fail with just linux mediacheck. I

On 07/27/15 10:06, Bowie Bailey wrote: > I have an old computer running CentOS 5. I need to add an SATA drive to > it, but it doesn't have any ports, so I need an add-on card. The board > only has a 32-bit PCI slot. Any recommendations on cards/brands that > work well with CentOS? I don't need any raid capabilities, I just need > a couple of SATA connections. > .

Hi, I have 4 x 500GB PATA Harddisk and I like to have them striped and mirrored. What is the best practise? Raid 0+1 or 1+0.. And how do i go about it? Thanks

Does anyone have information on support for Intel D965-based motherboards for CentOS 4 (i386)? I've got a DG965RYCK that fails a CentOS 4.4 install early on (problems scanning the PCI bus). Fedora Core 6 installs just fine. If anyone has any information, or magic boot parameters to try, please let me know. ("Works for me" is OK too). Thanks much. Dave Thompson UW-Madison

About 9 months ago, I made a policy decision to adopt RAID 1 on all systems I admin. (about 20 systems, all told) It's been a long, slow process. One of the systems is being upgraded from CentOS3 to CentOS4. It's been rock-solid stable for over a year. It's a "frankenserver" with parts from all over the place, maintained over years of active service. Currently,

Hello, We use all SCSI PCI card hardware RAIDs on all 4 of our production Asterisk servers. They all have Digium quad T1 cards and they all have from 2 to 4 T1s hooked up to them. We have had no noticable problems with dropped calls/poor quality. What are you looking to do with this system? what kind of traffic will be going through these 4 T1s? MATT--- -----Original Message----- From: Deon

Hello all, I've got CentOS 5.2 installed on an old Pentium III server. The server is used by a club at my school, and they are rapidly running out of room on the internal IDE drives that are configured in software RAID 1. I have a Silicon Image SATA controller in the server, and I was planning on adding two more SATA hard drives to the computer. Is there a GUI like Disk Druid for

I set up IDE software-RAID on a test machine for testing the recover functionality. The problem is that it somehow won't boot after removing the first disk, although grub etc. seems to be setup okay. Here's some background: 2 disks hda and hdb RAID 1 setup: /dev/md0 (hda1 + hdb1) /boot /dev/md1 (hda2 + hdb2) / /dev/md2 (hda3 + hdb3) swap done with disk druid during initial setup from

HI i'm so new to centos , Where can get it ? thank you centos-request at centos.org wrote: Send CentOS mailing list submissions to centos at centos.org To subscribe or unsubscribe via the World Wide Web, visit http://lists.centos.org/mailman/listinfo/centos or, via email, send a message with subject or body 'help' to centos-request at centos.org You can reach the person

HI i'm so new to centos , Where can get it ? thank you centos-request at centos.org wrote: Send CentOS mailing list submissions to centos at centos.org To subscribe or unsubscribe via the World Wide Web, visit http://lists.centos.org/mailman/listinfo/centos or, via email, send a message with subject or body 'help' to centos-request at centos.org You can reach the person

1. What am I trying to do?Deploy OpenStack using OOOQ (TripleO Quickstart) 2. What commands did I run?I ran:bash quickstart.sh $VIRTHOST 3. What was the exact output of these commands? fatal: [127.0.0.2]: FAILED! => {"changed": true, "cmd": ["virt-customize", "-a", "/home/stack/undercloud.qcow2", "--upload",

Hi, I have been trying to install CentOS 5.4 on a Intel SR1530SHS, Intel S3200SH mainboard.. It has a 3 x 1TB sata hotswap drives with LSI software raid onboard. I had configured the LSI to have Sata0 and Sata1 with raid 1 and the third drive as a hotspare drive. Format the harddisk and installation was a breeze. The server rebooted into a blank screen and the cursor just keep blinking. Please

Is it possible to partition a disk with Disk Druid and control the order of the partitions? I want to create my own boot and swap as RAID partitions but Disk Druid won't keep them in the order I want, no matter what I specify first. I've done this before by using fdisk to make the partitions before starting Disk Druid but I thought someone said this was an old bug and should have been

Thank you Paul for your suggestion. While implementing it, I found my error. As usual, it was an oversight of something already documented. When using MEMDISK for < 4MB images, {gpxe,ipxe}.usb files for example, you have to APPEND harddisk. Once that option was in place, I am now back to Syslinux perfection. I have to confess, this area of SA is some of the most fun, as it is a

I installed a 4.1 x86_64 with kernel 2.6.9-11.ELsmp (rpm) initially. My box is tyan 5350 and a SATA harddisk The install was successful and the harddisk was detected as /dev/sdaX But strangely, when I first reboot my machine. The harddisk change to /dev/hdaX What is the problem ? Below are some of dmesg output hda: WDC WD1200JD-00HBB0, ATA DISK drive Probing IDE interface ide1... Probing IDE

Hi, I'm experiencing recently happend kernel panics while making bacula backups on my external USB harddisk. It first happened some days ago while I was running 6.4-PRERLEASE. I then updated to 6.4-STABLE and enabled all the kernel debugging stuff. I've uploaded "screenshots" (including backtrace) here: http://pics.pofo.de/gallery/v/misc/ I'm now not sure if the external