similar to: Symlink outside the share path

Okay, this problem is solved. It turns out when I was doing the wide links and unix extensions option it really was working. It wasn't until I logged out and logged back in to the client to get a fresh smb connection that it worked. So I'm good. Thanks for the help everyone. I appreciate it. Kathy On Wed, Aug 20, 2014 at 11:28 AM, Kathy <banshee135 at gmail.com> wrote: >

on centos 7 I tried to install banshee from EPEL yum install banshee gotting this error: Error: Package: banshee-2.6.2-11.el7.x86_64 (epel) Requires: libgpod-sharp >= 0.8.2 You could try using --skip-broken to work around the problem You could try running: rpm -Va --nofiles --nodigest seems known problem but ignored to fix it in a year or more:

Hi, I'm having lots of difficulties with BCM5719, which is the default network card of HP Proliant DL 360 G8 servers. I can get a few ping replies before I get a couple of these: bge0: watchdog timeout -- resetting bge0: watchdog timeout -- resetting Then everything hangs. Can not log in using ssh.

Since upgrading from Ubuntu 10.10 I have had problems with graphics. The problems started after I initially upgraded to Ubuntu 11.04 but then installed xubuntu-desktop over it, but I have had the same problem all my fresh installs of Xubuntu 11.04 too. FPS previously averaging about 30 or 35 FPS while playing an OpenGL game with WINE now starts at 20 FPS for 2 or 3 minutes and then slows down to

Hi. I got this on today's RELENG_6 with Broadcom BCM5722 A0, ASIC rev. 0xa200. >From dmesg (bge related): bge0: <Broadcom BCM5722 A0, ASIC rev. 0xa200> mem 0xe8400000-0xe840ffff irq 16 at device 0.0 on pci2 bge0: firmware handshake timed out, found 0x4b657654 bge0: firmware handshake timed out, found 0x4b657654 bge0: EEPROM read timed out bge0: failed to read EEPROM device_attach:

Hi, this server, a Dell R720 has 4 bge on board, Broadcom NetXtreme Gigabit Ethernet, ASIC rev. 0x5720000 bge0: APE FW version: NCSI v1.1.7.0 bge0: CHIP ID 0x05720000; ASIC REV 0x5720; CHIP REV 0x57200; PCI-E miibus0: <MII bus> on bge0 ... I have connected the ethernet to port labeled 0, but it appears as bge2, how can this be corrected? thanks, danny

Hey, I tried it. The short answer is that nVIDIA cards are OK for text, but may not work at all under X. I downloaded the 3.3 ISO's, and burned new CD's. I did an X desktop install on a test bench P3 600 MHz system with a 4.3 gig drive. I did the install with a known-to-work Voodoo Banshee card to get the system going. I used a Mag DX1495 monitor, which I know does not to work on

http://bugs.freedesktop.org/show_bug.cgi?id=17896 Summary: no sound with 0.8.0-1 hardy w/ usb audio Product: swfdec Version: unspecified Platform: x86-64 (AMD64) OS/Version: Linux (All) Status: NEW Severity: major Priority: medium Component: plugin AssignedTo: swfdec at lists.freedesktop.org

Folks, Randomly, when the phone is taken off-hook, the the Iaxy produces a irritating banshee scream as opposed to a dial-tone. Cycling the power fixes the issue, & sometimes it magically goes away by itself. Has anyone experienced this issue & potentially fixed it? I'm using asterisk CVS head as of jun 17 2004. Thanks, Glen

Hi list, I have been trying to get the new file extension for Ogg FLAC (.oga) to work with Amarok. But it does not look to be possible due to limitations in the xine and gstreamer engines. Maybe the move to .oga was prematurely? I have done some testing with other players?including Banshee, Quod Libet, and others?but have not had any success with playing the .oga files. Only player I have

Fred Smith wrote: > On Tue, Jul 11, 2017 at 12:05:55PM +0100, Gary Stainburn wrote: >> I have just installed CentOS 6 i386 onto an old rack server (it's gonna >> be a Bacula storeage server and is a 1U 1/2 depth chassis) >> >> I did a minimum netinstall and so far so good. However, I have one >> problem. >> The CPU fan is going at full speed constantly.

Hey, I have two bits of info that suggest this is more of a RedHat problem than a Linux problem: 1) A high school friend had exactly this problem (screen when blank when booting up) on a computer running RedHat 9. (A different monitor had been used to install RedHat 9, and that monitor worked OK. Later, my high school friend got a different monitor, which went blank on boot up.) I solved the

Hi all, Here are some thoughts on Vorbis framing, which may make it easier to stream Vorbis in real time. The suggested changes also move more audio data closer to the beginning of each page. A note in the Vorbis framing spec suggests a simple 'bandwidth limited' mode whereby important information is placed at the front of each page and the end of each page is discarded. When operating

Well this is new. I haven't a clue what Dell has done on this R620, but this popped up today after I did a boat load of BIOS updates and tried to install stable/9 from our yahoo tree. If anyone sees the obvious solution here, I'd love to figure it out. found-> vendor=0x14e4, dev=0x165f, revid=0x00 domain=0, bus=2, slot=0, func=1 class=02-00-00, hdrtype=0x00, mfdev=1

Hi, I have tried to run half-life in linux with with wine. But there seams to be a problem with my graphics card. I can play games in linux with 3dfx support, but if I try to run half-life with wine it says that my graphics card doesn't support openGL. Does anyone know what I can do about this. I have got a Creative 3D Blaster Banshee. .^^.... $ecrets 2 $uccess Inc.

Has anyone gotten these drivers to work with any of their games? I'm trying for Counter-Strike(half-life mod) when i try it just sayes unsupported GL driver, though with the normal "Default" driver i have no problems, other than the lower fps, which the wicked3D drivers will fiks =) I've got all accelerations going for my voodoo banshee card, dri, and all that :D thanks

Hello scty library, I had huge problems with NVIDIA cards on Linux. The screen would go blank as soon as X tried to load. I only tried using the driver that came with CentOS. After lots of parts swapping, I found that the monitor (obviously) and (even) the motherboard make a difference. > If so what did you do about it. Finally, I gave up on NVIDIA cards -- I got a Voodoo Banshee

http://bugzilla.mindrot.org/show_bug.cgi?id=758 Summary: if authorized keys exchanged, regular user can gain Product: Portable OpenSSH Version: 3.6.1p2 Platform: ix86 URL: http://www.mainelinesys.com OS/Version: Linux Status: NEW Severity: security Priority: P2 Component: ssh

I am not sure if this first post made it to the list, but I wanted to post the resolution, which was very simple and something I had documented but buried and I had forgotten about it. All these problems went away when I joined the domain using Samba's version of "net", not Redhat's. If you use Redhat's version, it looks like it joins the domain but it really doesn't

Hi, A day or so after starting samba, some daemons (diferent forks) begin to hang. Then, the WinXP clients hang too completely. When I try to figure out what is happen, I see that smbd daemons hangs always in a fcntl64() call: # strace -p 6414 Process 6414 attached - interrupt to quit fcntl64(14, F_SETLKW64, {type=F_WRLCK, whence=SEEK_SET, start=3684, len=1} <unfinished ...> Process 6414