similar to: navigating to samba server by servername strangeness

Hi, I've using linux bonding in active-backup mode to combine two pairs of GigE NICs (eth0/eth1, eth2/eth3) into two logical bonds (bond0/bond1). All is working fine. However, I would like to specify a primary interface for each bond. This means I need to specify different options to the bonding module for each bond. I have tried every conceivable incantation of options and cannot get the

Hi! Is it HTB fully compatible with BOND interface? I have this setup (mode= fault tolerance) : BOND0 -> ETH0 + ETH1 BOND1 -> ETH2 + ETH3 ( http://www.kernel.org/pub/linux/kernel/people/marcelo/linux-2.4/Documentation/networking/bonding.txt ) HTB work very well with Class over BOND0. If I add Class for BOND1 it generate balance errors. Also with HTB.init

Hai, That bond0 interface, you might want to change that the interface name to bond1 Depending on the bonding settings, you might have hit a reserved name. I lots my docu on that but i know i configured a bond1 because bond0 didn work right. And then check these. wbinfo -pPt ( or wbinfo -p && wbinfo -P && wbinfo -t ) wbinfo --sids-to-unix-ids S-1-22-2-10513 wbinfo -D

Hello, Could someone tell me, how can I select from a dataframe only those columns whose names contain a certain text? For example, if the column names are "Bond1.Creditclass","Bond1.Price","Bond2.Creditclass","Bond2.Price", how do I select only the columns corresponding to Bond1? Thanks a lot, Mihai [[alternative HTML version deleted]]

Hi List, We're using bonding to create bond0 with 2 NICs, and noticing that CentOS 5 2.6.18-8.1.14.el5 (and presumably older) creates bond1 as well. I'd like to remove bond1 from the system, so that our monitoring scripts don't pick it up, except for those machines that actually do have a bond1. So... how does one remove bond1? Thanks! Misc info below of configuration and

Hi, Sorry for the broad distribution, I''m not sure who best can help me. I''m trying to add a new interface stanza to /etc/network/interfaces. With augtool, I can accomplish this with the following: set /files/etc/network/interfaces/iface[last()+1] bond1 set /files/etc/network/interfaces/iface[last()]/family inet set /files/etc/network/interfaces/iface[last()]/method dhcp set

Hi All I have two bond interfaces namely, bond0 and bond1. bond0 has two ethernet interfaces associated with it and bond1 also has two ethernet interfaces associated with it. Now i create a bridge interface namely br20 (20 being the VLAN) and assign it a IP Address , subnet mask and the default gateway. I will use this IP to reach the server. So it is like a management bridge for me.

Hi, Sometimes, I found one of my Mellanox NIC renamed to rename6, instead of eth1. The right names of NICs in my system should be: eth0 Mellanox NIC eth1 Mellanox NIC eth2 Intel NIC eth3 Intel NIC eth4 Intel NIC eth5 Intel NIC eth0 and eth1 will combined as bond1 with mode 4. However, the current names are: eth0 Mellanox

Hi all, I'm trying to setup a cluster of 2 machines with Centos 5.2 to host a postfix+spamassassin+clamav+mailscanner service. Below cluster software versions rgmanager.i386 2.0.38-2.el5_2.1 installed cman.i386 2.0.84-2.el5_2.2 installed Every machine (hp blade server ) has 4 interfaces, bounded in this way: Eth0, eth1

# modinfo ixgbe filename: /lib/modules/2.6.32-431.el6.x86_64/kernel/drivers/net/ixgbe/ixgbe.ko version: 3.15.1-k license: GPL description: Intel(R) 10 Gigabit PCI Express Network Driver author: Intel Corporation, <linux.nics at intel.com> srcversion: B390E9D9904338B52C2E361 I have updated this to 3.18.7-1 as well, same results # ifconfig bond1 |grep error

Hi all, Someone played with kickstart bonding with centos 6.4 ? CentOS 6.4, as upstream now support ifcae bonding in kickstart network section. I've an issue with configuring a second bonding iface in kicstart on CentOS 6.4. The first bonding (bond0) works as espected but the second is not configured during installation. I've a 6 nic server (two for "puclic" network, two for

Hi, I configured some ha services using heartbeat, I have this on my log: Nov 14 09:59:06 mail1 heartbeat[3932]: ERROR: Unable to send bcast [-1] packet: Operation not permitted Nov 14 09:59:06 mail1 heartbeat[3932]: ERROR: write failure on bcast bond1.: Operation not permitted how allow broadcast only on some interfaces with shorewall? attacched is shorewall status Thanks Nicola

Hi, I can't get "net view \\<servername>" to work from my Windows test client. It fails with "The network path was not found". I followed some of the online debugging guides and have found that a couple of the test nmblookups on the server are failing. The server is named 'fileserver1' and its IP address is 155.2.196.251 for the purpose of this email.

Hi All, I''m configuring my natting-firewall to do some tc shaping. Some traffic has to be shaped on 30mbit, some on 10mbit all the others are unlimited. The configuring and filtering works correctly. The traffic that is shaped at 30mbit is correct, but the traffic that is shapped at 10mbit only gets to 100KB/sec. It is on a device configured with bonding (both in and out interface).

Anyone know how to get statistics on bonded interfaces? I have a system that does not use eth0-3, rather we have bond0, bond1, bond2. The members of each bond are not eth0-3, rather they are eth6, eth7, etc. I didn't see anything in the man page about forcing sar to collect data on specific network interfaces.

hello, With CentOS 6.6, I try to configure two bonding interfaces via kickstart, but it works only with bond0, I don't understand why I can't configure bond1 the same way. I found this old post: http://lists.centos.org/pipermail/centos/2013-March/133439.html I have exactly the same problem. Who found the trick? best regards Fr?d?ric Benninger

Using Samba 2.2.7a on FreeBSD 4.7-STABLE. #uname -a FreeBSD fileserver1.smartrafficenter.net 4.7-STABLE FreeBSD 4.7-STABLE #0: Mon Dec 16 19:41:03 EST 2002 toor@fileserver1.smartrafficenter.net:/usr/obj/usr/src/sys/FILESERVER1 i386 All day long, constantly, I get the following messages in syslog: Jan 14 13:37:55 fileserver1 smbd[57969]: [2003/01/14 13:37:55, 0]

Using Samba 2.2.7a on FreeBSD 4.7-STABLE. #uname -a FreeBSD fileserver1.smartrafficenter.net 4.7-STABLE FreeBSD 4.7-STABLE #0: Mon Dec 16 19:41:03 EST 2002 +toor@fileserver1.smartrafficenter.net:/usr/obj/usr/src/sys/FILESERVER1 i386 All day long, constantly, I get the following messages in syslog: Jan 14 13:37:55 fileserver1 smbd[57969]: [2003/01/14 13:37:55, 0]

My syslog is constantly bombarded with these messages: Mar 27 07:15:35 fileserver1 smbd[70359]: [2003/03/27 07:15:35, 0] lib/util_sock.c:get_socket_addr(1012) Mar 27 07:15:35 fileserver1 smbd[70359]: getpeername failed. Error was Socket is not connected Mar 27 07:15:35 fileserver1 smbd[70359]: [2003/03/27 07:15:35, 0] lib/util_sock.c:write_socket_data(499) Mar 27 07:15:35 fileserver1

I have an odd automount problem. The first time I look in an automounted filesystem (when the mount is requested), it is empty; the second time it is not. Moreover, I only see this behavior on Centos 4.x systems, but not on Centos 5.0 systems going to the same fileserver. Here's an example, with some details simplified to clarify. In this example, fileserver1 is exporting fs1.