similar to: Moving from Redfone's Fonebridge to Allo 2nd Gen PRI card

I am looking for input on wether the 4 port T-1 foneBridge is a useful device in a asterisk deployment. Would it be better to loadup a extra asterisk server to trunk the T-1's via IAX or is TDMoE safe in production enviroments. We are only looking at 2 T-1's, one for pstn and the other to a channel bank. Any advice? Bruce Reeves Nortex Networks -------------- next part -------------- An

We have been using Red-fone foneBridge2 Quad T1/E1 for last few years. As these devices are not available anymore, we are looking for alternatives. Are there any similar devices available ? -- Regards, Tirveni Yadav www.udyansh.org What is this Universe ? From what it arises ? Into what does it go? In freedom it arises, In freedom it rests and into freedom it melts away. Upanishads.

I hope someone can help me out with this issue. It has been dogging me for months and I can't seem to get it to go away. I have a Rhino Ceros box running Asterisk 1.4.21.2 connected via eth0 (nVidia MCP61 Ethernet) to a RedFone FoneBRIDGE2 dual-port with EC. The FB is the latest hardware rev and the latest firmware. I'm running the latest fonulator version and I'm running Zap-1.4.11

Hello! I have problems with audio in conference zap sip, I have choppy audio. I believe this problem is cause by de echo canceller from the fonebridge that I use in my system. Can someone explain me how I can disable the echo canceller form the fonebridge? I'm using dual port T1/E1 foneBRIDGE2 Thanks!! -------------- next part -------------- An HTML attachment was scrubbed... URL:

If you have been affected by the SunRocket / ALLO folding issue, ChiliTech would like to extend our hand to you to help you in this time. We will transfer your numbers to us for no cost, and will match your SunRocket or ALLO rate. Please contact us at 1-866-678-6858 x 126 or e-mail mhoppes at chilitech.net. We have been around since 2001 serving the Internet community. Matt Hoppes ChiliTech

Dear all, I'm searching someone who already installed allo.com gsm card with Asterisk NOW. I installed the hardware in my new server, but when runing dahdi_genconf I always have the "no span" message. I tried to install the driver according to allo.com doc, but it seems not up to date, and maybe done more specificly for an appliance.. >[root at localhost ~]# dahdi_genconf

On Tue, Jan 20, 2015 at 12:43 AM, Scott Griepentrog <sgriepentrog at digium.com > wrote: > I would recommend capturing traffic outside your Asterisk server with > Wireshark, then running the Telephony/Rtp/Analysize Streams option to > determine if you have packet loss at that point in the network. > > On Mon, Jan 19, 2015 at 1:00 PM, Todd R. <tjrlist at live.com> wrote:

I've been evaluating Asterisk for a while, and things seem to be going very well. The issue of redundancy and automatic fail-over is now on my mind. I searched the archives and googled for solutions, but didn't really come up with much. We'll be using queues (modified), which precludes some of the standard redundancy solutions, since the queue needs to know all the agents

So here is my setup. Hardware: Intel P3 1.2 Ghz 1 GB RAM 36 GB Drives Mirrored Software: CentOS 5 2.6.18 Kernel Asterisk 1.4.14 Zaptel 1.4.7 (redfone) LIbpri 1.4.2 I'm using TDMoE with my PRI using a product called fonebridge from a company called redfone. They require that I use their own build of zaptel and I am trying to figure out if the problem is with them or something else. The

Hello List Does anybody have any experience with the FoneBridge line of products from RedFone? I think their HA implementation sounds interesting, and like the prospect of having dedicated hardware for our PRI connections. Kind Regards Jon Leren Sch?pzinsky

Hey guys, I am trying to diagnose a hum in my FXO lines I am using an Adtran 750 with 8 FXO ports. I am getting a pretty bad hum on the line during a call. I have checked the Telco side of the 66 block and there is no hum there so it's my problem to fix. I have tried to lower the gain but that reduces the call volume to much. Where else should I be looking? Setup as follows Dell

I am preparing to connect an asterisk box with a redfone fonebridge to a T1 service provider. I am doing this by testing first with another asterisk and a Sangoma card playing the role of telco. I formerly had this test configuration operating flawlessly as a PRI connection. But I discovered that I will need to use E&M, thus I've chosen the parameters as described in the subject

We tried them out early last year when we were looking at a large deployment and they gave us a lot of the redundancy that we wanted. However we did run into issues where calls seemed to get caught up in the system. It was as far as we could tell rather random. No consistency to it at all. Asterisk hung up the call but the telco side of the line didn't actually hang up. The channel was left

Hi Everybody, I'm trying to connect an asterisk box to a provider using Redfone Fonebridge dual E1. Installation seems to run correctly only i can't get the D Channel up and i have the following error displayed. DYN/ SPAN ethmf <mac_address_fo_fbport> Expected seq no 0 , but received 3456 instead . This error keep scrolling until i disconnect the

I'm scoping out HA for a relatively simple Office/Call Center PBX. Current setup uses a TE412P with 4 PRI our telco with SIP hard/soft phones for users. Some outbound also goes to a SIP provider. Active/Active looks to be too much hassle for an installation this size, so we're looking at adding an extra * in an active/passive configuration with Linux-HA in between them. Does anyone

I'll take either.... Actually now that I have had a chance to think about what I did (sorry bad week here). Yes, I will admit I did patrionize the users list... sorry if I offended anyone. I just figured I'd try to help any SunRocket users out that may not be on the biz list. If you review my history, you'll see I only post business stuff to the biz list. This is an exception.

When tar'ing up an ext3 filesystem on a 3ware RAID I have, I got the following errors in my system log: Apr 7 21:27:46 allo 3w-xxxx[957]: Drive error encountered on port 3 on controller ID:0. Check cables and drives for media errors. (0xa) Apr 7 21:27:46 allo kernel: 3w-xxxx: scsi0: Command failed: status = 0xc7, flags = 0x51, unit #0. Apr 7 21:27:58 allo last message repeated 3 times Apr

Hello everyone, I'm using redfone fonebridge to have Pstn connectivity on my asterisk box. I can receive in coming calls however outgoing calls don't go to provider. It's seems it's a span config problem. Because in systemconf when I try to config span as follow span=1,0,2,ccs,hdb3,crc4 And start dhadi I have the following message Unable to

Was'nt sure if this mail got through earlier: I have been having a weird issue with my telco's ISDN PRI occasionally resetting on a incoming call, i suspect it to possibly be a timing issue since some of the incoming call work. This problem happens very frequently. I am using asterisk-1.6.0.1 with libpri-1.4.9, the asterisk server is connected viw TDMoE to a Redfone Fonebridge into

Has anyone every attempted to set up a mini PC to achieve much the same functionality as the fonebridge box? The sort of thing I'm imagining is a micro itx board & case in a completely solid state configuration (flash disk, maybe a psu fan but only if really required), with a TE210P (or equiv) card(s). The sole purpose of this would be to be a bridge between E1 lines and TDMoE. The