similar to: Connecting Asterisk and BT Versatility PBX via NT BRI

Hi Olivier It seems wrong configuration, because according to your mail Asterisk it will be acting as terminal mode (ie Patton gateway acting as network and asterisk as terminal). But Asterisk message is indicated Asterisk a s a NT mode [ 212.226050] wctdm24xxp 0000:0a:01.0: xhfc: Configuring port 0 span 1 in NT mode with termination resistance ENABLED. It could help by checking parameters on

Roberto Thanks. Panasonic KX-TD1232 system ISDN interface use DDK plug, not same cord you are using for openvox B400P card. Each port could be configured as CO or extension port as Point-Point or PTMP in both mode. Regarding to dial timeout these it becomes from ISDN dial mode overlap or En-bloc, by the way you can close dialling number by using # key. Best regards Mc GRATH Ricardo E-Mail

Panasonic PBX KX-TDA600 it doesn't support SIP protocol for VoIP technology it only support H323 Trunk through 4 or 16 channels gateway card and TDM technology with ISDN BRI and PRI card. Mc GRATH Ricardo

hi, anybody know how to make a sip trunk between trixbox and panasonic kx tde 100? i've tried, but always failed when calling from trixbox to panasonic. thanks,,, -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20130312/1dd5170b/attachment.htm>

Hi All, I've a BT Versatility PBX that I want to connect to my asterisk 11.9.0 box via BRI port in NT mode but actually I wasn't able to get it working. I've another standalone PBX, it's a Panasonic model, which works fine connected to the same port. The BT connected to a UK BT BRI line works quite fine after roughly a minute once connected. The PBX can be seen at

Can be done calls from each system? How about to capture data with Wireshark? I have experiences Asterisk with Panasonic with H323 without any problem. Mc GRATH Ricardo E-Mail mcgrathr at mail2web.com

Hi Leonardo At first should be useful to post your message at asterisk-r2-request at lists.digium.com group. By the other way let me advice, to make an explained detail of your problem as; Asterisk version Openr2 version Configurations files Dialplan dahdi pattern detail Detail of the call process (inbound or outbound call failed?) In case of outbound call failed extension dial wait time of

Hi It seems these device it works similar way as a Cisco phone, so no way to look how to configure the phone because is based on template files downloaded from main system, files are downloading by TFTP option #66 (new software configurations file etc.) when device boot up. If user need to configures directory and others "My Allworx manager " it should made through system ip address or

Hello, All :) Regarding to incoming caller ID on PSTN line, which one is best supported by asterisk: is it FSK ETSI or FSK US? I bought some caller ID converter hardware (convert DTMF to FSK and vice versa) but still asterisk can not detect it. The converter has a switch FSK ETSI or FSK US This is what I put in /etc/asterisk/chan_dahdi.conf ... cidsignalling=bell cidstart=ring ... If after

hi everyone, Is it possible to serially connect my panasonic KX-TD1232 with a Linux box(Asterisk installed) and have it working? -- P. K. kakarizz@fastmail.fm

I have a samba server running samba 3. I am not actually sure that this is samba not working or a linux printing thing. I have a Linksys PPSX1 Pocket Print Server and I am unable to print to the network printer. There are directions on the Linksys site but I get so far and the directions tell me to type a command that is not found. Is anyone printing to a Linksys Pocket Print Server? I need

Hello, I want to use Asterisk PBX in front of my old, legacy PBX. The legacy PBX can be outfitted with caller-ID and is already able to handle Calling Party Control Signal Detection (this is a Panasonic KX-TD1232 Super Hybrid PBX. My question is how would one enable Asterisk to control the TDM400P/FXS port to provide to the /FXO CO port on the legacy PBX, support for proper answer supervision/CPC

Hi all, There is someone with some experience interconnecting a Panasonic digital PBX (KX-TD1232) with Asterisk? Thank you and best regards, Dan

OK, I've downloaded and unzipped the firmware files in ipw2200-fw-3.0.tgz - so I have 4 files: ipw2200-bss.fw, ipw2200-ibss.fw, ipw2200-sniffer.fw and LICENSE.ipw2200-fw, all of which I've placed in the /lib/firmware directory. Unfortunately, the instructions in README.ipw2200 and INSTALL are not clear as to what to do next. I'm using CentOS 5 on my (Dell) laptop so setting-up wireless

Hello We have around 50 phones in our company, and I am playing with the thought to gradually go over to using sip services and ip-phones internally. However at first I would liked the Asterisk just to sit between the phone line and the Panaosnic, so I can take out one lin/number at a time to use ip phones. I am new to Asterisk, and haven't done much configuring of the PBX either. So I also

Dear Friends, I do require centos 4.2 x86_64 cds here in delhi,India. If anyone of you can arrange that for me i will be vary grateful. The requirement is urgent. Thanks for your time and effort. -- Regards Abhishek Jain -------------------------------------------------------------------- mail2web - Check your email from the web at http://mail2web.com/ .

Hi There, I've moved some Windows2012 with MSSQL VMs from an hold ESXi 5.5 machine to a more recent and powerful machine running Fedora 24 x86_64 and related libvirt + KVM virtualization. I've moved the VMs filesystem to LVM slices and installed the VirtIO drivers in to all Windows VMs. I've also set both Disk and Network interface to work using VirtIO. So far so good everything works

ðÏÞÅÍÕ ÂÙ É ÎÅÔ? ÷ÏÐÒÏÓ ÔÏÌØËÏ × ÔÏÍ, ËÁË Õ ÔÅÂÑ ÂÕÄÅÔ ÓÏÅÄÉÎÑÔØÓÑ ÐÁÎÁÓÏÎÉË Ó ÁÓÔÅÒÉÓËÏÍ. Date: Wed, 30 Jul 2003 20:06:17 +0400 From: Pavel Zheltouhov <pavlo@comlink.ru> To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] asterisk,ata186 and Panasonic TD1232 Reply-To: asterisk-users@lists.digium.com I have Panasonic TD1232 pbx, few cisco ata186 and linux box with asterisk.

If Someone did that, How I connect extensions.conf with this type of Hybrid system to work with asterisk inside this schema: PSTN--->PANASONIC KX <------> Asterisk | |--------->send internal call Thanks.

I've installed ipw2200-firmware-3.0-3.nodist.rf from RPMForge using yum OK. I've loaded the ipw modules with /sbin/modprobe ipw2200 and then /sbin/lsmod | grep ipw which gives: ipw2200 136873 0 ieee80211 33417 1 ipw2200 However, when I run system-config-network I don't see Intel Coporation PRO/Wireless 2200BG (eth1) in the list of adapters. Also, when I