similar to: Voice clarity issue

Hi, Could you please help me!! I am trying to configure the Asterisk server. I have a analog phone connected to a FXS port of a Cisco 3745 router. This router is connected to a Asterisk server via Fast Ethernet interface. I am trying to make a call from the analog phone to a SIP client. This SIP client is registered to the Asterisk server. Analog phone number: 999 SIP client : 202 Sip client IP

Hi, in my dial plan I've configured two trunks to make outbound calls (one for national calls and other international). I want to allow only 2-3 extension to make use of my international trunk to make outbound calls so I want some kind of auth. based on their callerid . Please guide. thanks arun -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello All, I have a Digium Wildcard TE410P Quad-Span T1 Card, when I do connect T1 lines it goes in RED. When I do connect the same line on a different Server (Same Model T1 Card) it works fine. How do I examine/diagnose my T1 Card for any hardware failures. I heard about loopback test , how helpful it is? Here are my configuration /etc/zaptel.conf span=1,1,0,esf,b8zs

Hi, In my dial plan I've configured two trunks to make outbound calls (trunk1 and trunk2) to same service provider but I want when any of my exten starts with _2. should goto trunk2 and there should be some kind of disturbance (like some noise or some background noise) when my calls goes to trunk2 to make the call quality bad. Mainly I want to achieve bad call quality on trunk2 by adding

Trying this again after my first away from work in a couple weeks. Running Asterisk 13.0.0 IP authentication with Vitelity I can Originate with sip, but not pjsip. Here is the sip settings and trace. Action: Originate ActionID: S8 Channel: SIP/8005555555 at outbound.vitelity.net Exten: createcall Context: TestApp Priority: 1 Timeout: 60000 CallerID: John Doe <1234> Variable:

Dear all, I use Trixbox as my PBX. Until a couple of days I've installed a GSM Gateway to communicate with our three cellular phones: 15 64227777 15 64228888 15 64229999 The GSM Gateway has just one SIM. I use the Free PBX web interface in order to set up the route and trunk parameters: Trunk: ******* Name: SIM1 Peer details: host=10.10.1.2 (IP from GSM Gateway) port=5060 type=peer

Hello, everyone. Right now, we are trying launch our own PBX system based on Asterisk(Fedora) with Cisco 2611. Cisco has 2 port FXO card installed on it. For testing, I have 2611 hooked into phone line with number of xxx-xxx-xxxx fine. (I'll call it F). Using softphone, I can dial in extension 1001 on asterisk, which should talk to cisco. After initial connection to Asterisk, I have try to

we got this installation : WinSip(demo version) -> ser(radius accounting) -> asterisk(from sip to h323 channel) -> gsm gateway(with 32 sims in it) we configured winsip to make 28 calls like from 28 different sip accounts, to 28 different cellular phones numbers after the first ten : -- Executing Dial("SIP/5060-081925b0", "OH323/33xxxxxx@gsm.gateway.ip") in

Let me explain: When I dial into Asterisk ( I have a SIP trunk - which I need to make sure is not faulty), I only get one-way voice communication. The calling party, from the SIP trunk hears nothing - the extension rings on the Asterisk server (you can see it in the CLI and hear it at the computer), and the softphone rings However, when you answer the SIP softphone , you can only hear the

Greetings List. we're facing a strange case with my system where in the middle of the call .. after like 7 minutes (not necessarily ) the callee is unable to hear the caller however the caller is able to hear the called party. the scenario is the following. 1- 15 computers running Windows XP SP3 joining a Windows Domain Controller with DHCP , DNS, ISA Internet Acceleration Server. 2- Internet

Ok I have spent the last week working on getting my small PBX to work. I will in the end only have 4 SIP extensions being either softphones of IP phones. Currently only 1 SIP config for testing. And at the this point it should be all fairly easy with all inbound and outbound to PSTN will be going Via Firefly/Freshtel.net in Australia via IAX. Inbound does work in it's current basic state.

Hi All, I am trying to use iconnecthere to make outbound calls. I am behind a linksys router. I keep getting this error 481 "Call Leg/Transaction Does Not Exist". Does anyone have any prior experience with this problem. Any leads will be much appreciated. Attached are the conf files and logs #SIP.CONF ; SIP Configuration for Asterisk [general] port = 5060 ; Port

Hello, I am looking for ideas and suggestions. I want to use a 16 port GSM gateway as a trunk for outbound/inbound. I will also have two PSTN phone lines coming into the Asterisk server. All calls will go to an IVR on the Asterisk PBX. Outbound from extensions will route to GSM-GW when the dialed number matches a pattern set in the GSM-GW trunk. And accordingly for the PSTN trunks. But that's

Hi I've install Asterisk 1.4.2 and its working fine. In my sip.conf I've allowed ulaw and g729. I want to change the codec for outbond calls. Please help not able to find anything using search. thanks arun -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070501/af78de7a/attachment.htm

Hello everyone, I am facing a strange problem on my asterisk box (using isdn lines with pri card installed on it). Normal incoming/outgoing calls are working perfectly fine. When a user dial a wrong/out-of-service number they don't hear back any such message like "The number is wrong or user is switched off" in some cases, and it's just a silence for the user. Now while

I created an account at IAXTEL.com to route 1-700-XXX-XXXX calls through. IAXTEL.com gave me a number (example) of 700-555-6226. I have made the following changes to my: /etc/asterisk/extensions.conf: [iaxtel700] exten => _81700XXXXXXX,1,Dial(IAX2/myusername:mypassword@iaxtel.com/${EXTEN:1}) exten => _81800NXXXXXX,1,Dial(IAX2/myusername:mypassword@iaxtel.com/${EXTEN:1})

Dear all, I am from Saudi Arabiya and I am using digium hardware with asterisk 1.6. When I am executing following AMI originate API. Orginate start to execute extenstion without knowing of PSTN(FXO) channel is ringing. Any one can help me to resolve this issue ? Action: Originate Channel: Dahdi/g0/2923878 Context: outbound-ivr Exten: 1234 Priority: 1 ActionID: ABC45678901234567890

I have an analog GSM Gateway that is connected to a normal SIP ATA device. Basically what it does is this : when you call the extension nr. of the SIP ATA port, the GSM Gateway will pick up the phone and presents a (new) dial tone, and then dials whichever DTMF tones it received. The SIP ATA ia a Grandstream HT286. I would like to use the GSM Gateway to route my outbound cellular calls, how

2014-11-12 2:45 GMT-02:00 Luis Eduardo Cortes <luedcortes at gmail.com>: > Hello: > > I'm newbie in asterisk, please help me. > > My context is as follows: > > 192.168.4.2 --> Asterisk 11.13.1 complied from source > > 192.168.4.4 --> Yeastar NeoGate TG100 GSM gateway > > When I call from a GSM cell phone, my TG100 GSM gateway answers and > dials

Hi Cheers, Thanks for your information, multiple spaces in the DN having issues while deleting object, Could you help us how can we permanently delete those User Regards, Arun Kumar B Infrastructure Support Group | www.dsmsoft.com Phone: +91 7871148192 *Disclaimer:* This email and any files transmitted with it are confidential and intended solely for the use of the individual or entity