similar to: Using asterisk as voicemail for cisco call manager

Has anybody successfully (or I guess unsuccessfully for that matter) implemented Cisco Call Manager and used an * box for voicemail? I checked the wiki and google and I see some references to Call Manager Express and *, but CME is completely different than CM. If anybody has done this or has any insight, it would be appeciated. We are trying to migrate ~ 300 users off of Cisco Unity and

Hello; I need to use Cisco IP Phones with Asterisk and I have some questions to know how to use it if someone can advise: 1) How I can assign for each button an extension? 2) How I can assign for specific button a feature to be used (like call forward or call pickup .. etc)? 3) As you know that it is required to have a correct username and password to login, so where to give the username and

It can be done. 1. Setup a new Vm profile on CCM with a mask of XXXX 2. Setup a CTI route point: a. Set the directory number to a pattern. I use *27XX but any pattern that you can send from * is good, ie. 88XXX b. Set the VM profile to the newly created profile c. Set the line to forward all calls to VM 3. Change the dialplan in * to append the extension called to the

Hi All; Already in the voicemail.conf file, I added the extension 500 and kindly find below my voicemail configuration: [Internal] 0 => 1234,Gama Operator,Operator at gama.com 500 => 1234,Operator,Operator at gama.com 501 => 1234,Employer Name,employer_email at gama.com 502 => 1234,Employer Name,employer_email at gama.com Asterisk version is 1.8 and currently I am getting this

Hi, I've got a CCM ( Cisco Call Manager ), with a Cisco Unity VM server and about 45 SCCP phones on the ccm, and 200 users on unity. we want to migrate all users to IP Phones to ditch our ancient phone system. I would love to get Linksys-Sipura SPA-941s for the 150 users not on IP phones yet and run sip to an asterisk server, but have their voicemail on Unity. these phones are $150 each,

Hi All; Again, the Cisco IP Phones 7942G and using Skinny: I upgraded the firmware to version 8.5 (skinny) and I am using skinny channel (chan_skinny) and the skinny.conf file. The phones are registering, but when we use them to place a call, we only hear tooooooooooo in the handset and we do not hear voice (even when we dial the digits, we only hear toooooooo .. but it dials and destination

Hi All; Any one can suggest a TFTP server to be installed in Fedora (same machine that Asterisk is installed) to be used for Cisco IP Phones to download the required firmware and configuration files. Thanks for the help in advance. Regards Bilal

Hi All; How to configure the buttons in the Cisco IP Phones to be used for different functionalities like "Call Forward, Call Pickup, ... etc"? For example, if I need to assign one of the buttons existed at Cisco IP Phone to be used for CallFrw, how to do this in Asterisk? Regards Bilal

On Wed, 23 Jul 2003, Yifang Dai wrote: > I wish! My company just spend a lot $$ on the shinny CCM phone system, so I > don't think I can change that easily... But if I can get asterisk to > talk to CCM via h323, and prove it's usefulness, I might have a chance > to use * in the branches... Well, good luck, then! > By the way, do you know if we can get *'s VM to

ive had enough of cisco unity and microsoft exchange and im looking for alternatives to our voip system. right now, we have 3 cisco callmanagers, 1 cisco ip icd system, and 1 cisco unity voicemail system. all phones are cisco 7940/7960's and some ata186/188's. voice gateways are cisco vg200's with pri cards (5 total). im running h323 on the gateways and phones are of course

Hi All; Can anyone advise if using Cisco IP Phones in skinny protocol is fine or not? Or it is better to use it in SIP protocol? Regards Bilal

Hi Guys I have just come from a customer that is looking to install 13 Cisco CallManagers into all their branches, (i tried to convince them to go *). They are looking for a voicemail solution. Now as Kinesis and Unity are way too expensive (apparently cisco is launching a cheap voicemail system too) I was thinking of installing * as the voicemail solution. Lots of goggling i have found

Hello; I am facing a problem to let Cisco IP Phone 7942G register on Asterisk. The firmware has been downloaded from the TFTP successfully and currently I am running this load SIP42.9-3-1SR2-1S* I feel that there is a problem in the SEPMAC.cnf.xml but really I do not know which one to be used exactly. Basically, there is some effect that appears on the Phone (for example, it is appearing the

Hi all, We want to put an Asterisk Voicemail Server behind a Cisco Call Manager. The idea is to have Cisco Phones (SCCP) registred to the CCM and the voicemail in the Asterisk Box. The trunk inter PBX is in SIP. My question is: Is it possible to activate MWI LED from the Asterisk to the Cisco Phones registred to the CCM when they receive a new voicemail ? Thanks in advance Fred

Has anyone here any experience in getting an Asterisk box to talk to a Cisco Unity system? I have a potential customer who would like to add a conference bridge to their existing Cisco Unity setup. The digging I have done so far suggests that it should be possible to talk SIP between them, but I'd be interested in any stories of success or failure. Cheers Tony -- Tony Mountifield Work: tony

On my 7905s I can configure a "voicemail" number, which in turn activates a "Messages" softkey. When pressed, it goes to that exten, which in turn is configured to go to VoiceMailMain. Great, works like a charm. However, the phones also have a "go to voicemail timeout" after which, the phone diverts the call to voicemail via a "temporarily moved". This

Hi; How can I know the duration that the DAHDI channel is still used? I need to know its status and since when it is in this status, how? Also, is it possible to hangup the channel if it has been openned more than 90 minute? Other than using the timeout in the Dial command (because this I know it). What is happening with me that from time to time, I find some DAHDI channels are stayed connected

Appreciate the kindly help and advise. Regards Bilal --------------------- > > Bilal, > > I suggest you turn on logging on your tftp server to see > what files are actually being requested, and if the the tftp > server is dishing them out... Try adding a few v's to your > tftp setup: > > File: /etc/xinetd.d/tftp > Line to change: server_args = -s /tftpboot -v

can anyone give me a reference to the retrieval of voicemail from the Asterisk PBX using a cisco 7940 phine running sip image. i have configured a single voicemail box using the script, the corresponding entry in voicemail.conf and configured the extension to use the voicemail box . i can see from the asterisk console the message being passed to the voice mailbox, and correspondingly the sip

Hi All; I need a help as the voicemail need GSM codec while I am using G729 for the call, why Asterisk does not do codec translation from G729 to GSM, it does not support? Any need for settings, what I am missing? Regards Bilal ____________________________________________________________________________________ Looking for last minute shopping deals? Find them fast with Yahoo! Search.