similar to: WebRTC and Asterisk 12

Hi I'm using asterisk 1.8 Does anyone know how to use the queue reload command. The built in help doesn't really help. queue reload {parameters|membe Reload queues, members, queue rules, or parameters Regards Ish -- Ishfaq Malik Department: VOIP Support Company: Packnet Limited t: +44 (0)845 004 4994 f: +44 (0)161 660 9825 e: ish at pack-net.co.uk w: http://www.pack-net.co.uk

Hi Is there any way to set the presence state of a peer to in-use in asterisk 1.8? The idea is to integrate DND buttons on phones to BLF. Regards -- Ishfaq Malik Department: VOIP Support Company: Packnet Limited t: +44 (0)161 660 2350 f: +44 (0)161 660 9825 e: ish at pack-net.co.uk w: http://www.pack-net.co.uk Registered Address: PACKNET LIMITED, Duplex 2, Ducie House 37 Ducie Street

Hi I'm just about to upgrade to version 1.8.29.0 and have compiled with SRTP. However, we exclusively use the asterisk realtime architecture using the mysql connector. Looking at tutorials we have to set encryption=yes and transport=tls for any peer we want encrypted traffic for. Having a look at contrib/realtime/mysql/sippeers.sql from the source code shows that the encryption column is

Hi I'm using asterisk 1.8.23.1 but I've seen this same issue in previous versions of 1.8. I have created some work arounds but the behaviour is incorrect. This is the scenario: Call comes in and goes to appropriate dialplan In the dialplan the call is forwarded to another number using a Local channel (and using /n ) e.g. Dial(Local/<my-number>@outbound-context/n,60) The number is

Hi All, I have a question about the Queues. I'm using Asterisk 11.13.0 , and I want to configure the following setup : When there is an incoming call to the queue all agents should ring even those that are already in call, they should receive a second call. Is this doable in any Asterisk version ? Thanks in advance. -------------- next part -------------- An HTML attachment was

We use the ringall strategy for a small queue with 4 members. When a call comes in, if one of the members is busy, all the phones except the busy phone rings (as intended). While the other phones are ringing, if this busy phone becomes available again, we would like to have it start ringing. Right now it just sits idle. Is this possible? I played with ringinuse (queues.conf) and callcounter

Hello, I would like to setup a mechanism to trigger an alarm if user is deal too many numbers within a very short period of time. Safeguard against users hacked accounts. can someone help? Thanks,

I have many endpoints and each endpoint has some parameter in common so i wonder is there any way to config one for all endpoints? Like in my example I have two endpoints and I repeat the same thing, [100] type=endpoint aors=100 auth=100-auth allow=ulaw,alaw,gsm,g726 context=from-internal callerid=device <100> dtmf_mode=rfc4733 use_avpf=no ice_support=no

Hi guys We're using asterisk 1.8.23.1 on CentOS 5 and are trying to create a trunk to MS Lync server. If I create the peer in sip.conf the trunk connects with no problem. However, we prefer to use ARA. Whenever we define the peer in our peers table, the trunk does not work, even if we use sip show peer <peer-name> load. Has anyone got any experience of connecting to Lync using ARA?

Hi people I'm just mailing to see what people are using for CTI solutions with asterisk. Aslos, has anyone managed to integrate asterisk with Salesforce? Thanks in Advance Ish -- Ishfaq Malik Department: VOIP Support Company: Packnet Limited t: +44 (0)845 004 4994 f: +44 (0)161 660 9825 e: ish at pack-net.co.uk w: http://www.pack-net.co.uk Registered Address: PACKNET LIMITED, Duplex 2,

HI there I was wondering if anyone has implemented voicemail to text and if so, what package is being used to do so? Thanks in Advance Ish -- Ishfaq Malik Department: VOIP Support Company: Packnet Limited t: +44 (0)845 004 4994 f: +44 (0)161 660 9825 e: ish at pack-net.co.uk w: http://www.pack-net.co.uk Registered Address: PACKNET LIMITED, Duplex 2, Ducie House 37 Ducie Street Manchester,

Hi Is there any harm in using res_mysql for some things and res_odbc for others? We already use res_mysql for ARA but could do with having CEL logged to MySQL. Thanks in Advance Ish -- Ishfaq Malik Department: VOIP Support Company: Packnet Limited t: +44 (0)845 004 4994 f: +44 (0)161 660 9825 e: ish at pack-net.co.uk w: http://www.pack-net.co.uk Registered Address: PACKNET LIMITED, Duplex

Hi I'm using asterisk 1.8 but I'm sure this applies to other versions. If someone puts a call divert on a handset such as a Snom phone I get this type of SIP message on receipt of an inbound call: Got SIP response 302 "Moved Temporarily" back from xxx.xxx.xxx.xxx:xxxxx Which then triggers a local channel to make the call. Is there any way I can access that IP address inside

Hi We're using asterisk 1.8.23.1. Our inbound calls are routed into the default context with explicit number matching. If found they are passed on to a distinct context for the number being called using the Goto application. If the call is successful or even if it has no answer, the cdr dcontext field has the correct second context. However, if the call fails or is busy, and even though we

I work on the Asterisk side of things and admit to not knowing about browser development. A co-worker asked me today why they should develop a web based agent software using WebRTC? They prefer to develop using a SIP based javascript library they found. Can anyone offer some insight on why to choose either WebRTC or a SIP library for a web based agent software connecting up to an asterisk

I'm asking about this scenario: Asterisk(public IP) <--> Internet <--> Router (public IP) <--> SIP client (private IP and NAT) What settings in sip.conf will give this the best fighting chance of working? We already have nat=force_rport,comedia

Hi, I am trying to setup asterisk so that anyone from any IP can call using any callerid as long they have an account - also no registration is required. However, it seems like asterisk tries to find peer based on either the IP address or from header. What I really want is asterisk to find account/peer based on username passed as part of the authentication and NOT from the IP address or the

Are they any gotchas to be aware of in getting Asterisk and Lync 2013 talking to each other using SIP? Or is Lync a pretty standard implementation of SIP? Cheers Tony -- Tony Mountifield Work: tony at softins.co.uk - http://www.softins.co.uk Play: tony at mountifield.org - http://tony.mountifield.org

Has anyone here used Asterisk inside a WatchGuard firewall, talking via the WatchGuard SIP Application Layer Gateway to an outside SIP service? I have a customer doing just that, and I am 100% convinced there is a bug in the ALG regarding the media port number it inserts into the SDP when it rewrites it. However, either they or WatchGuard will not accept there is a bug, despite my very detailed