similar to: AsteriskNOW with AX1600P card

Hello I'm trying to install Dahdi through source code on a Fedora 13 host to use an OpenVox PCI card with a single FXO port, but dahdi_cfg -vv isn't happy. 1. After successfully running "make all; make install; make config", I edited /etc/dahdi/system.conf thusly: loadzone=fr defaultzone=fr fxsks=1 2. Then ran "dahdi_cfg -vv" which says: ------------- DAHDI Tools

Hello, After installing on Ubuntu 10.04 using the tutorial on http://hmontoliu.blogspot.com/2010/03/installing-asterisk-and-freepbx-on.html I have a running instance of Asterisk. PROBLEM: result of dahdi_cfg: DAHDI Tools Version - 2.2.1 DAHDI Version: 2.2.1 Echo Canceller(s): MG2 Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Echo Canceler: mg2)

Hello everyone, I have a Atcom AX-1600P(1) card with a FXO module and I can't configure it. I have four extension with this PJSIP settings: --- /etc/asterisk/pjsip.conf --- [transport-udp] type=transport protocol=udp bind=0.0.0.0 [6001] type=endpoint transport=transport-udp context=from-internal disallow=all allow=ulaw auth=6001 aors=6001 direct_media=no rtp_symmetric=yes force_rport=yes

Hi, I have done my best and tired of searching the net about the problem. If anybody could help would be a great favour. Description of Problem ------------------------ I am trying to install two Netpci cards(Traverse Technology Netjet ISDN-s) on Trixbox 2 and aim is to use in Asterisk as dailin and dialout. I compliled the driver as directed in the manufacture manual. After installation dmesg

Hello, I just got my isdn-card working together with i4l and asterisk. Everything seems to be working fine: I can accept calls coming from the outside and I can dial out. Even setting the msn works like charm but my problem is that I cannot hear a word. There's complete silence in both directions. Any idea what could be the cause? Thanks for your help, Gunther Lspci: 0000:01:07.0 Network

Asterisk - 1.8.4.1 Dahdi-linux - 2.4.1.2 Dahdi-tools - 2.4.1 Kernel: 2.6.37.6 Kernel BKL: enabled I am upgrading Asterisk on this box. It has an OpenVox A400P PCI analog card with 1 FXO and 1FXS module. This server has been running just fine for two years with Asterisk 1.6.1.0 I've just upgraded all the OS and installed Asterisk 1.8.4.1. On trying to configure the A400P I get: # modprobe

I'm trying to use a Teles (netjet) ISDN BRI card with asterisk 1.2.9.1 Anyone was able to use this card with asterisk? I couldn't find much information about it. Any help?

Hi, Last weekend I was planning to buy a physical PBX system, but instead I have been blown away by the fact that VoIP really works, that Asterisk is so easy to set up and use... and free! We're in Australia, so as I understand it, we aren't allowed to use the Zaptel cards. We need to set up our system to route incoming 56K data calls to the PPP daemon on our Linux box or to our

Hi, I am receiving calls via a Netjet-S card on asterisk, and I notice that whenever I am talkimng to someone, if their voice is loud enough, sometimes asterisk generates a DTMF Tone as they speak. that is played to me. (Caller doesn't hear it). Any ideas how to stop this?

dahdi_cfg -vvv error `cut: '/sys/bus/dahdi_devices/devices/pci:0000:01:00.0/spantype': No such file or directory` PRI show spans --command not found test call not working. -- dahdi_genconf -vvv Default parameters from /etc/dahdi/genconf_parameters Generating /etc/dahdi/assigned-spans.conf cut: '/sys/bus/dahdi_devices/devices/pci:0000:01:00.0/spantype': No such file or

Hi, It's the first time i try to configure an ISDN card with dahdi, so my experience is very poor (be kind ;)) My problem is with dahdi_genconf, when i start it it says: /usr/sbin/dahdi_span_assignments: Missing '/sys/bus/dahdi_devices/devices' (DAHDI driver unloaded?) Command failed (status=256): 'dahdi_span_assignments dumpconfig > /etc/dahdi/assigned-spans.conf' at

Hello, I am trying to use 2 netjet cards under asterisk and isdn4linux. I am having a hard time trying to get them to work in terms of dial out. Does anyone have a working config I could look at for even one card (tried that, not much luck either). When i dial out: -- Accepting AUTHENTICATED call from 172.16.11.2, requested format = 2, actual format = 2 -- Executing

Hi, I am using a Netjet-s ISDN Card, and am having some trouble dialling out (Incoming Works Fine). TRUNK=Modem/ttyI0 exten => _90XXXXXXXXX,1,Dial(${TRUNK}/${EXTEN:1}||Ttm) exten => _90XXXXXXXXX,2,Congestion I get the following when diallingout: -- Starting simple switch on 'Zap/2-1' -- Executing Dial("Zap/2-1", "Modem/ttyI0/04XXXXXXXX||Ttm") in new

Hello, I'm researching the possibility of using VOIP (SIP) with an existing PABX system. Ideally, the setup would be to dial an outside line through the PABX (that would actually link to the the VOIP gateway). At this point I would prefer not to purchase a hardware-based VOIP gateway. I would prefer to use a software-based gateway for research & testing purposes. Could anyone please

Well, it has been a long time since I used my NetJet S cards with asterisk (moved to the quad PRI card) but I am trying to get this working again for home use. Basically, what I am using is this: Linux 2.6.8.1: config lines: # ISDN subsystem CONFIG_ISDN=y # Old ISDN4Linux CONFIG_ISDN_I4L=y # CONFIG_ISDN_PPP is not set CONFIG_ISDN_AUDIO=y # CONFIG_ISDN_TTY_FAX is not set CONFIG_ISDN_DRV_HISAX=y

Hi, I'm after some ISDN card resellers in Australia. I've noticed the AVM cards should work well here, however I've found the reseller here has no website, is listed in Yellow pages as management consultants (??) and when I called quoted almost $400. Does anyone know where I can get the AVMs in Australia a bit cheaper or another card (not the Netjet) that works with Asterisk.

I'll try again using my subscribed address... Apologies to the moderators... --- Hi All, I've successfully got SIP and IAX2 working on Asterisk using X-Lite as a SIP phone and talking to a remote Asterisk over IAX2 using G729. I'm now trying to get an ISDN BRI connection working. I have a Traverse NetJet card (http://www.traverse.com.au/) which I currently have working with

I'm trying to get a basic Asterisk configuration together for ISDN incoming / outgoing calls. I have two Cisco 7905g phones working (at least talking to each other) and have purchased a NETjet-S PCI ISDN card for routing calls to / from ISDN. The state I've managed to get it to is:- -- Executing Ringing("SIP/PHONE2-d557", "") in new stack -- Executing

I would just like to get a refresh of the situation for Australian users. It would seem that the TE400P is currently available and is likely to acheive approval for use in Australia within the next 2 months ? (when is the end of summer?). Once this is done, it will certainly suit larger installations, but it still leaves a number of 'gaps'. Anyone with analog phone lines will need

I have the following software installed in a Centos Box with a TE420 (5th Gen) card. . Centos 6.5 64-bit . Asterisk 1.4.22 . dahdi-linux-complete-2.9.1.1+2.9.1 . libpri-1.4.14. Even without plugging in the ISDN into span 1, all 4 spans are flashing red. Plugging an E1 into span 1 makes no difference. My system.conf is just simply: loadzone=au defaultzone=au span=1,1,0,ccs,hdb3,crc4 bchan=1-15