similar to: Integration with NEC DSX - help with dial line

Hi all, I've seen a couple of posts recently from people who are doing something with Asterisk and a T100P and a Nortel PBX. However it's not clear exactly what they are doing. Does anyone know if it's possible to use a T100P or T400P as a DSX-1 interface to connect to a T1/PRI CO module in a Nortel PBX? We have a Nortel Norstar Modular ICS PBX and I'd like to plug its CO

Hi, How can I make calls from Asterisk client to NEC NEAX 2400 traditional phone ? Is it possible to have a connection between Asterisk and NEC NEAX 2400, since NEC-NEAX2400 is an IP-PBX and supports SIP. Please help me to find a solution ;;; Thanks & Regards Ram Kumar Customer Support Engineer Barcode Gulf LLC Dubai , UAE Mobile : + 971 50 5594178 Email : Ramkumar@barcodegulf.net

I have an nec electra elite 192 with a t1 card; and am looking for suggestions as to integrating them (can't throw out the system yet!). I have a fully working asterisk server -CVS-04/27/04-19:01:05- (found a hp d220 for $350.00!), 2 digium t100p cards, a plain t1 with loopstart signaling, and 2 working bt102 grandstream ip phones (thanks again Matt for your "start from scratch"

I am currently attempting to get Asterisk working with our existing NEC IPK 192 system. The * box has a Wildcard X100P clone card in it and is hooked to an analog port on the NEC system. The analog port is shared between an elevator phone and a credit card machine. I have one SIP extension configured in * which the softphone on my Windows PC is registered to. With the softphone I am able to

hi. i connected Asterisk to an NEC NEAX system with a crossover T1 cable and the Digium TE405P using E&M wink signaling. the connection's ok. however when dialing from the NEC to the Asterisk. most of the time the Asterisk only sees the first digit of the dialed number(which is 4 digits). some time if i dialed the 4 digits very fast it might get through. seems like there's a timming

Hi, We are currently in the process of installing an Asterisk box between our legacy PBX (NEC Xen Master) and the Telco (Telstra). Originally the PBX was connected to the telco via 8x BRIs. Our new Asterisk box has been setup with 2 OpenVox B800P cards. Each card has the 4 ports in TE mode and 4 ports in NT mode. The NEC PBX is connected to the Asterisk boxes NT ports and the Asterisk box is

Hi all, When configuring Asterisk with an ISDN card, it will at one point become necessary to select the LBO (Line Build-Out) value. This is an integer (0-7) that is determined by the length of the cable and is selected from the following table. Many of us are familiar with it: CSU (dB) DSX-1 (feet) ------------------------------- 0 0 0?133 1

Is there anyone out there who has tried to connect up an asterisk box to make and take calls through a NEC NEAX 2400 using Q.sig or anything like it? Can anyone tell me if it is possible? Thanks in advance, Phil Allred Brooklyn Law School

Hi All: We have cooperation PBX as NEC, I am wondering how to replace our legacy ACD by using Asterisk, but not losing tie line connection to NEC. Does anyone have any idea how to make it work? Many thanks, Tilein

hi * users, anyone out there ever come across, worked with or heard anything about NEC's Univerge SV7000 Telephony Server? Link is at http://www.univerge.nec.com/products/list/sv7000/sv7000.html I'm just wondering whether it's as flexible, programmable and configurable as Asterisk. It also looks like they've got a whole range of IP phones

I'm using QSIG between an NEC SV8300 and Asterisk (after giving up with CCIS). Things work pretty well with the exception of issues on stations on the SV8300. When I call from Asterisk to a SV8300 station and I send my extension as the caller ID number, it shows up on the SV8300 as "OPERATOR". I've tried a few different TON/NPI values with no difference. If I set callerid to a

I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72

http://bugzilla.mindrot.org/show_bug.cgi?id=465 djm at mindrot.org changed: What |Removed |Added ---------------------------------------------------------------------------- Status|NEW |RESOLVED Resolution| |FIXED ------- Additional Comments From djm at mindrot.org 2003-02-24 15:46

I have done additional testing and I haven't been able to figure out why it's failing. Since my original testing we now set the realm on the authentication section to match what we receive from NEC. It's of the format abc at xyz.com I have verified the md5_cred several times and it matches the user:realm:password formula 3016:insiph at something0a646666.com:3016 where username is

Hello, we’d like to propose the integration of a new backend into LLVM: NEC SX-Aurora TSUBASA Vector Engine (VE). We hope to get some feedback here and at EuroLLVM about the path and proper procedure of merging. The SX-Aurora VE is a Vector CPU on an PCI-E Accelerator card. It has 48GB memory from six HBM2 stacks, accessible with 1.2TB/s bandwidth, 8 cores with vector and scalar units, each.

Hi, so I just bought a NEC 1300A, primarily, because it allows me to write DVD+ and -RW. Using DVD-R discs (and currently no options to try other media, due to shops being closed), I'm unable to write anything, using either the dvd+rwtools port, or the dvdrtools. I've exhausted all references to be found in google, which are in a language I understand, so I'm hoping the list can

Hi, I have 2 servers: one is running 2 B410P cards with 8 euroisdn lines (mISDN) connected on it, everything runs fine. I prepare a new server - HP 360 G8- with 2 HA8 cards each of them 1 module of 4 lines. Already had with this machine an RMA on both cards as they was faulty and crashed the server. What happends is that when I connect cables on the HA8 modules (those cables are unpluged

Hi, I'm am currently in the process of trying to integrate an * box with an NEC Electra Elite IPK. Currently, we have 7 POTS lines coming into our building. These lines are plugged into our NEC using the appropriate analog line interface card from NEC. The NEC effectively has NO configuration done to it, other than to make all the internal phones ring when a call comes in. We also

Hi all, anyone could pls explain me what does it means ? It a part of zaptel.conf file. LBO= Line Build Out 0: 0 dB (CSU) / 0 - 133 feet (DSX-1) 1: 133 - 266 feet (DSX-1) 2: 266 - 299 feet (DSX-1) 3: 399 - 533 feet (DSX-1) 4: 533 - 655 feet (DSX-1) 5: -7.5 dB (CSU) 6: -15 dB (CSU) 7: -22.5 dB (CSU) Thanks Giordano -- No virus found in this outgoing message. Checked by AVG

I'm working on an Asterisk system with all of it's PRI ports configured with the LBO setting at 5, like this: span=3,0,5,esf,b8zs As of yet, I am unwilling to change the LBO to 0 to where it probably should be because the system is working and I'm not sure exactly what the LBO does. I'm aware some changes were made to deal with low audio levels. Does anybody know what audio