similar to: loop-start and ground-start

I am trying to find an example of how to set up my FXS Station Card in my Asterisk. I have (1) XP100P I have (1) tdm20B (2 Port FXS) Could someone tell me if this is correct? /etc/zaptel.conf fxsks=1 fxoks=2 fxoks=3 loadzone=us defaultzone=us /etc/asterisk/zapata.conf [channels] ; language=en ; ;X100P Port 1 context=inbound-analog signalling=fxs_ks usecallerid=yes echocancel=yes

I just purchased a T100p from digium and a Carrier Access Access Bank 1 channel bank (12fxs/12fxo). I have the setup partially working thanks to some help from IRC. However I still have the following issues I can't seem to resolve 1. When calling into the system from the PSTN call hangup is not detected. * leaves line in use until it is shutdown. 2. When calling an analog phone connected to

Help. Why is it that I can call out from my GSBudgetone SIP phone but the audio is "one-way'? Why is it that when I call my asterisk phone number, I get a fast busy?

I have a system that I am trying to get a port on a Sangoma A104d card connected to an Adtran 850 with 5 FXS modules and 1 FXO module. A problem I am having is figuring out what cable should be used from the port on the Sangoma to the JP2 port on the Adtran. Tried was a cross-over T1 (1->4, 2->5, 4->1, 5->2) as well as a straight T1 (1->1, 2->2, 4->4, 5->5). Neither one

Hi everyone, Sometimes i am having problems with Zap channels on asterisk 1.2 (Disc-OS 1.1), after some calls, the channel continues in use, even after hanging the call up, then i need to run the "soft hangup Zap/<zapchannel>" in the asterisk CLI to release the channel. Here is my zapata.conf: [trunkgroups] [channels] language=pt_BR context=default usecallerid=yes

All, I'm having trouble getting the X100P working. Lsmod shows : zaptel 179808 0 I did a . # modprobe zaptel and here is my zaptel.conf (comments omitted) __SNIP__ fxsks=1 loadzone = us defaultzone=us __SNIP__ Here is zapata.conf __SNIP__ [trunkgroups] [channels] context=default switchtype=national signalling=fxo_ls rxwink=300 usecallerid=yes hidecallerid=no

Hi. I have a x100p card installed on my asterisk box... my zapata.conf file includes the following lines: [channels] context=default switchtype=national signalling=fxo_ls rxwink=300 echocancel=yes rxgain=0.0 txgain=0.0 group=1 callgroup=1 pickupgroup=1 Basically, the zapata.conf file generated by make samples. Then in my extensions.conf I have this: [default] include => demo And demo is

Hi, I am using TDM400 card with 3 fxs and 1 fxo. I am struggling to detect hangup tone or disconnect supervision tone from my CO. I attached the recorded wav file which contains my telco's disconnect supervision. I am using , asterisk-1.4.33.1 dahdi-linux-complete-2.3.0.1+ 2.3.0 OS => Debian-lenny 5 users.conf ------------- [trunk_1] trunkname = pstn ; GUI

Sorry to post such a newb set of questions but I have been hammering about trying to get Asterisk running on FC2 machine reading everything available (I think that is what stuffed me, shouldn't have read it all :-) ). Config FC2 running Asterisk 1.0.0, with the h323 compiled in and installed correctly. Amazingly enough I have everything compiled correctly and installed. I am running a

Hello All, I am getting a set of errors when I boot Asterisk that I have not been able to solve. What is causing these error(s)? Asterisk boot output: ============== Asterisk CVS-04/10/04-21:44:51, Copyright (C) 1999-2001 Linux Support Services, Inc. Written by Mark Spencer <markster@linux-support.net> ========================================================================= [

Scenario, I got some very good help earlier from Joseph getting me up and started but I have a couple of small problems still. Setup: FC2 Asterisk 1.0 Zaptel 1.0, TMP400P, FXS Port 1 FXO Port 4 Analog dialout line and Analog handset plugged in. Problems: 1. Incoming calls work and the phone rings and can be answered no problems, (although I wouldn't mind being able to adjust the ring but

i belong to india. i am making pbx using sangoma fxo card. i want that when ever call comes to my PSTN line i should see the no from where call is coming. so i have to configures chan_dahdi.conf according to my region. i checked dahdi.conf and in that they have mentioned for india

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

Hi All, I have just migrated from Asterisk 1.0.0 to Asterisk 1.0.5 and I have an X100P installed. The old asterisk was working, but now the new version isn't picking up any calls! However, I did notice that after installation, I performed modprobe zaptel and modprobe wcfxo and they worked fine, but when I executed ztcfg, I get the following errors: ioctl(ZT_LOADZONE) failed: Invalid

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all! I'm testing a telephone connected to FXS port of a Sangoma A200 card. But I'm observing that callerid is not working. The configuration that I'm using in chan_dahdi.conf is the following one: - --------------------------------------------------------------------- ;autogenerated by /usr/sbin/wancfg_dahdi do not hand edit

Hi, I am using asterisk 1.4.28 with freepbx and Wildcard TDM410P card. Everything is working fine except the caller ID of incoming call from PSTN line. The phone display is showing "Unknown" when there is an incoming call. *My log file showing this while an incoming call on PSTN line:* tail -f /var/log/asterisk/full [Dec 30 06:36:16] DEBUG[2559] dsp.c: dsp busy pattern set to 0,0

My outgoing FXO calls are answered but have no audio in either direction if I have callprogress=no in chan_dahdi.conf. If I change to callprogress=yes then the audio returns. My chan_dahdi.conf file is listed below. Can anyone point-out why callprogress=no isn't working? #cat /tmp/a [trunkgroups] [channels] language=en context=incoming toneduration=40 ;usedistinctiveringdetection=yes

Hi, I've seen this USB product from Sangoma : http://www.sangoma.com/products_and_solutions/hardware/analog_telephony/usb_fxo.html Is it working ok ? Is it easy to integrate it with Asterisk ? How would you rate your experience with it ? Regards -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello, All :) Regarding to incoming caller ID on PSTN line, which one is best supported by asterisk: is it FSK ETSI or FSK US? I bought some caller ID converter hardware (convert DTMF to FSK and vice versa) but still asterisk can not detect it. The converter has a switch FSK ETSI or FSK US This is what I put in /etc/asterisk/chan_dahdi.conf ... cidsignalling=bell cidstart=ring ... If after

I am trying to configure a channel bank with 24 ports of FXS., but appear to be hitting a roadblock? This worked on v1.4.xx but now just get "SimpleSwitch" and immediate=no/yes don't seem to make a difference?, no matter if under top section, under channel, etc. Chan_dahdi.conf: [channels] context=default usecallerid=yes hidecallerid=no callwaiting=yes usecallingpres=yes