similar to: Asterisk TON number

Only a warning, and doesn't seem to do anything bad. But I can't seem to figure out what these warnings mean? -- Requested transfer capability: 0x00 - SPEECH [Feb 17 12:33:03] WARNING[10750]: chan_dahdi.c:3096 dahdi_call: Unrecognized prilocaldialplan NPI modifier: k [Feb 17 12:33:03] WARNING[10750]: chan_dahdi.c:3096 dahdi_call: Unrecognized prilocaldialplan NPI modifier: o [Feb 17

Hello, I have an Asterisk system in the UK using ISDN service from BT. My problem is that the called number is always passed to the provider with the Type Of Number declared as ?national? despite pridialplan (and prilocaldialplan) is set to ?unknown?. My questions are: - How can I find out what the effective value is for the above two variables without actually making a call? (I have very

Hi All, This posting regarding PRI voice optimization, on dahdi 2.1.0.4. we have more than 4 machine running on 4 port PRI card with echo cancellation hardware based. i have enabled echo cancel from chan_dahdi.conf using echocancel=yes, now more than 70% of call get good voice but some of calls having issue for callquality and other voice related issues. now my question is that is there any

Hi all, I have Asterisk working great for a while now, and until now, only needed to forward calls which originate from one country (Holland, +31). We have a Wildcard TE410P card and configured it in zapata.conf as: switchtype: euroisdn pridialplan: unknown ...etc This was all fine, but now we want to also forward calls to the voice-switch with a calling-number with a different country code.

Dear Customer Support, i connected the asterisk to a e1 interface of our hipath4000. outgoing calls from a sip peer of my asterisk to an up0 telephone which iss connected to the hipath4000 are working. If you want to dial from an up0 device to the e1 interface where asterisk is connected to, you have to use the prefix 83. But when you enter the 3rd cipher this error appears at the cli

hi folks. i recently setup an Asterisk system in Hong Kong. their phone company told me that their T1 PRI switch type is Primary-NTT. however in chan_dahdi.conf there's no such option. i have it set to national. it worked fine for a while, but now suddenly stop working. in coming call just keep ringing and didn't even show up on console. out going call hang up immediately with cause code

hi,all i have just set up asterisk 1.6.0.7 rc1 with spandsp 0.0.5 pre4 to ReceiveFAX, link to a E1 (DE410P) using dahdi this can receive the fax from E1 successfully, but i see many error message in the log like this: [Mar 16 09:24:38] ERROR[23540] channel.c: ast_read() called with no recorded file descriptor. when i receive a 5 pages fax, i will see this error message over 200 lines..... it

hello:I used libpri 1.4.12 version with asterisk 1.8.7, after the pcap files, i found thatin wireshark setup message, the number type always changed from subscriber to national number.i have set pridialplan= local and prilocaldialplan=local in chan_dahdi.conf already. because that, the systemsometimes can not make outgoing calls. anyone can clarify that? Best regards, James.zhu Doing

Hi, I have installed Elastix 1.5.2 (Barranquilla, Colombia (TELCO: METROTEL)) with a TE220P (2xE1) and TDM2400P (16FXS), openr2 is included in 1.5.2 version. The outcoming calls are ok, but with incoming call i have an error: ERROR*[*14972*]* chan_dahdi.c: Chan 2 - Protocol error. Reason = Multi Frequency Cycle Timeout, R2 State = Seize ACK Transmitted, MF state = Category Request Transmitted,

hi folks. recently some of our customers complained about bad voice quality on the phone system. i looked at the logs and found a lot of these: [2012-11-03 08:26:38] NOTICE[11305] chan_dahdi.c: PRI got event: HDLC Abort (6) on D-channel of span 1 [2012-11-03 08:26:45] NOTICE[11305] chan_dahdi.c: PRI got event: HDLC Abort (6) on D-channel of span 1 [2012-11-03 08:26:54] NOTICE[11305]

I installed Trixbox and a TDM400P with 2 FXO and 2 FXS ports and am having an annoying issue with the FXO ports. As soon as I plug either one into the phone line it's as though the line is disconnected i.e. get disconnected tone when trying to dial out, line is busy when dialling in. The CLI shows the following: trixbox1*CLI> zap show channel 4 Channel: 4 File Descriptor: 18 Span: 11*

PRI debug of the entire call would be great, also, switchtype would be awesome as well. Thanks! Matthew Fredrickson On Thu, Mar 24, 2016 at 4:07 PM, Carlos Rojas <crt.rojas at gmail.com> wrote: > Hi > > Did you activate the pri debug on the cli asterisk? > > On Thu, Mar 24, 2016 at 12:59 PM, Carlos Chavez <cursor at telecomabmex.com> > wrote: >> >>

hello: thanks for Tzafrir Cohen for dahdi testing. I installed dahdi-2.1-r3c svn code and asterisk1-6 for testing OpenVox B400P and junghans card. i fund that there is bug (i think) to dectect NT or TE mode. actually on the board, i set it as TE mode, but after start wcb4xxp, but it show the port is NT mode. to detect the TE mode, I modefy the code in base.c

Hello, Is it possible, for testing, to connect an cat5 straight patch cord between 2 ports of a Digium B410P card and use these 2 ports as a normal dahdi trunk ? I've tried this: One port is set as NT, the other as TE. I would expect timing to come for system hardware so I choose in /etc/dahdi/system.conf : span=1,0,0,ccs,ami span=2,0,0,ccs,ami Results: - both ports lights are green -

<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN"> <html> <head> </head> <body bgcolor="#ffffff" text="#000000"> Hi everione,<br> <br> I'm make some test with pri timer T309. I'm using asterisk 1.4.23.1, libpri 1.4.9, dahdi-linux 2.1.0.4 and dahdi-tools 2.1.0.2. But in my tests, the timer fail with a telco

Hello to all, I have a problem with an asterisk qsig. I have three machines: Nortel CS1000 --- Card Sangoma PRI ---> Asterisk QSIG ---SIP Trunk---> Asterisk I use Snom phones on Asterisk. If I call from Asterisk to Nortel, Nortel reminds me of the name of the person i'm calling and I visualize on the display of Snom phone, but if I call from Nortel to Asterisk, the QSIG does not send

Hi, Does anyone know what it means when I've got an incoming fax routed through to iaxmodem+hylafax and then I see this in the asterisk log: DEBUG[18902] chan_dahdi.c: Detected digit 'f' This happens just after the initial fax negotiation has started and seems to correspond with the sending fax machine giving up. Googling hasn't helped me here :( -- Cheers, Kingsley.

Hi list! I am installing an * box that will be installed on a site with KPN BRI ISDN in The Netherlands. I am using bristuff fron Junghanns. Does anybody know the correct settings for this? I will not have internet access there which makes it harder to google around on location. switchtype = euroisdn is pretty obvious but what about these settings: signalling = bri_cpe_ptmp ; p2p TE mode

Hi list! What exactly is the meaning / function of the pridialplan & prilocaldialplan? I've been trying to find out what the different possibilities for these settings are but couldn't find a clear answer. The possible parameters I could find are are : local,unknown,dynamic,national,international and maybe there are more? Thanks!

Hi I;ve trixbox installed with 2 NICs. One NIC carries the MPLS-VPN traffic (only a 1 MB link without internet for carrying voice to another site) while the other NIC has a connection with public IP for internet services on that machine. the first NIC (eth0) has IP of 172.16.0.1 and is connected to router with WAN IP: 10.18.6.254 , the second IP is 203.234.82.98 (eth1). i want to have the