similar to: [XCP] Import Always Fails

I just ordered quite a few servers, and, without verifying ahead of time, ordered without hard drives planning to boot over iSCSI using the built-in network cards (NOT an iSCSI HBA). I''m wondering if anyone has tried (and hopefully succeeded) installing XCP to an iSCSI volume using a network card with iSCSI boot support and the software iSCSI initiator in XCP. Obviously I can order HDs

Hi, I''ve been trying to use E5520 and X5650 together in an heterogeneous pool without success. I know the combination is not on the official XenServer supported list (http://hcl.xensource.com/CPUPoolsList.aspx), but I thought it would be possible to set the mask anyway and see for myself if the combination works… My problem is that the mask doesn''t "stick" after a

Well, now that I''ve figured out that network booting XCP is not really going to be feasible, I''m moving on to my next option: flash media installation. The systems that I purchased have SDHC slots on them, so I figured I''d attempt to install XCP to one of these cards. I had already read that there''s a minimum disk size in the installer (apparently 12 GB in

So, a few days ago I asked about network/iSCSI booting XCP (dom0). Doesn''t seem like it''s something that very many people have done, since I didn''t get much response, so I decided to give it a shot myself. I was able to install a couple of CentOS 5 packages that help with network booting and get the system to boot off of NFS (can provide some more detail on that,

Hi, I am trying to install openxencenter to control my VMs I followed the instructions but when I tried to start it I got:  File "window.py", line 44, in <module>     import gtkvnc ImportError: No module named gtkvnc does any one face this problem before. I tried to comment the import line and xencenter started but console tab is not working and it is lookoing for gtkvnc module.

Hello, I hope to be in the right list. my question is the following. I can''t seem to get multipathing configure on XCP 1.6. In XenCenter I was able to enable "Multipath" however, in the LUN under general tab I see " multipath 1 of 1 active", the the CLI I do the following command xe --m node session it list only one session. Can someone help me please? Thanks in

This may be a better question for the Xen-Devel list, but I''ll start here... Does anyone know if there is any easy way to replace the gPXE ROM with a newer version in Xen? Also, anyone know if there are any plans to have some sort of option in the domU config file to specify a boot rom? Looks like qemu-dm has an "-option-rom" option - is there any way in Xen to make use of

When trying to use the GPL PV drivers with Windows 7 x64 (and testsigning turned on), I get a BSOD with a STOP 0x00000101 error. There''s also an error at the top that says "A clock interrupt was not received on a secondary processor within the allocated time interval." Is this STOP error related to the HPET or other timing adjustments for Xen? Any advice on things I should

I''m using Xen with SLES10 and am using NPIV to attach FC SAN disks to my domUs. I''ve resize one of the disks on my SAN and I''m wondering if there''s a way to force Xen to rescan/resize the block device without shutting down the domU or unmounting the volume. Thanks, Nick -------- This e-mail may contain confidential and privileged material for the sole use

I'm having trouble getting a host to join an ADS domain/realm. I have smb.conf set correctly, with the workgroup, realm, and security = ads specified. However, when I try to join with the command: net ads join -U Administrator, I simple get the message "Aborted" and it does not join the domain. If I use the -d flag to enable debugging, I see the following toward the end of the

Hi. I have some new 64bit Windows 2008 R2 domU''s running on SLES11/xen_3.4.2. What is everyone using to get 1gb network performance on win2k8? I''ve used GPLPV on win2k3, but I see you have to sign the drivers yourself for 64bit. Maybe that process isn''t difficult, I only glance at the link from gplpv''s page. What is everyone using? GPLPV is about the only

Hey, everyone, I''m running Xen 3.2 (SLES10) and trying to get an OpenSolaris PV domU to run correctly. I''ve followed a couple of the instruction sets out on the Xen wiki and other folks blogs, but I''m running into an issue with the domU crashing. The OpenSolaris version is the latest development release - 5.11-0.128. The config looks like this:

Well, I seem to have developed a strange issue with the GPL PV drivers in Windows. I''m running Xen 3.2 on SLES 10 SP2 and running some Windows XP HVM domUs. Most (12-15) of my Windows machines work just fine. Two of them, though, have started exhibiting a strange behavior with intermittent network connectivity. Basically, the network starts up and connects initially. After some

----- Original Message ----- > From: "Jeremy Allison" <jra at samba.org> > To: "Nick E Couchman" <nick.couchman at seakr.com> > Cc: samba at lists.samba.org > Sent: Thursday, December 3, 2015 6:13:51 PM > Subject: Re: [Samba] Linux & NFSv4 ACLs > On Thu, Dec 03, 2015 at 06:03:39PM -0700, Nick Couchman wrote: >> >> > On Dec 3,

I'm attempting to configure Samba with CUPS as a centralized print server. I've done this in the past - my current production server is running Samba 3.2.14. On my current production server, I have several users set up as either "admin users" or "print admin" users so that they can manage the drivers, etc., on the Samba server. In setting up my new server, I'm

Hi, folks, I''m attempting to run an e-mail server on Xen. The e-mail system is Novell GroupWise, and it serves about 250 users. The disk volume for the e-mail is on my SAN, and I''ve attached the FC LUN to my Xen host, then used the "phy:/dev..." method to forward the disk through to the domU. I''m running into an issue with high I/O wait on the box (~250%)

> On Dec 3, 2015, at 17:24, Jeremy Allison <jra at samba.org> wrote: > >> On Thu, Dec 03, 2015 at 03:54:21PM -0700, Nick Couchman wrote: >> I have a situation where I need to share, via Samba, a filesystem mounted via NFSv4. I'm struggling with the best way to make Samba see the NFSv4 ACLs and enumerate them to provide the proper SMB/CIFS access to the files, instead

HVM = fully virtualized. The question is, why are you using fully virtualized domUs? Why not paravirtualized (PV)? >>> On 2008/06/16 at 16:07, Rudi Ahlers <Rudi@SoftDux.com> wrote: Itamar - IspBrasil wrote: > why you''re using hvm ? its slow > > > > Rudi Ahlers wrote: >> Hi all >> >> I''m running CentOS 5.1 x64 + Xen 3.0 & I

----- Original Message ----- > From: "Jeremy Allison" <jra at samba.org> > To: "Nick E Couchman" <nick.couchman at seakr.com> > Cc: samba at lists.samba.org > Sent: Friday, December 4, 2015 1:22:06 PM > Subject: Re: [Samba] Linux & NFSv4 ACLs > On Thu, Dec 03, 2015 at 07:31:36PM -0700, Nick Couchman wrote: >> >> Try these pages (U

I've seen a couple of posts related to this, but nothing with definitive solutions or even hints that helped me in the right direction. I'm attempting to add Samba4 DCs to my existing AD domain. This mostly works - it replicates in information from the Windows DCs, starts the services, and appears to have all of the necessary information. Scheduled replications from the Windows DCs to