similar to: Installing asterisk and dahdi on ubuntu

Hi List; I compiled Zaptel 1.4 and Asterisk 1.4 after downloading them using svn, but when I checked the file zaptel.conf under etc/asterisk, I did not find this file. Any help? By the way: How can I know the asterisk and zaptel version extactly that I compiled them? In other words, asterisk 1.4.... and zaptel 1.4.... ? Regards ------------- ITS IP Telephony and Contact Center Engineer Eng.

Hi List; What is the command and where I can write it to block specific code from calls (then no one will be able to place call for any number start by that code)? --------------- Regards ITS IP Telephony and Contact Center Engineer Eng. Bilal Ghayad Mobile: + (965) 9849460 Yahoo ID: bilmar_gh at yahoo.com MSN ID: bghayad at hotmail.com

Hi All; To download, compile and install DAHDI, do I need to download the both (dahdi-kernel and dahdi-tools) If yes, then do I need to do the compilation and installation command for each package? What is the method to download, compile and install the both packages as one package? By the way: Why there is dahdi-kernel and dahdi-tools? In other words, for what the kernel is used and for what

Hi All; In dahdi: what we use instead of ztcfg -vv (that is existed /sbin/ztcfg -vv). ? Regards Bilal

Hi; How can I know the duration that the DAHDI channel is still used? I need to know its status and since when it is in this status, how? Also, is it possible to hangup the channel if it has been openned more than 90 minute? Other than using the timeout in the Dial command (because this I know it). What is happening with me that from time to time, I find some DAHDI channels are stayed connected

Hi List; I am using Firefly softphone Version 1.9.9 Build 4521 and I select IAX protocol and did the configuration in Network1 (and I checked the Active checkbox) as following: Server: 192.168.8.4 username: iax2user1 password: password In the Asterisk, I did the following configuration on the /etc/asterisk/iax.conf: [iax2user1] type=friend context=internal username=iax2user1 secret=password

Hi to all. I'm trying to use meetme on asterisk 1.4.22.1. On a debian i've compiled (as i need h323 support) openh323_v1_18_0 pwlib_v1_10_0 dahdi-linux-2.1.0.3 dahdi-tools-2.1.0.2 asterisk-1.4.22.1 All works fine, dahdi status is: asterik:/data/programmi# /etc/init.d/dahdi status ### Span 1: DAHDI_DUMMY/1 "DAHDI_DUMMY/1 (source: RTC) 1" (MASTER) asterik:/data/programmi#

Hi All; I have an E1 card with two ports for ISDN PRI. Do I need to install DAHDI in addition to LIBPRI? For placing outside calls (outgoing) via the PRI, then in the extension.exe file, I will use the Dial function? But how can I determine that I need to use the PRI channels and not the analoge channels? Last point: how can I know that asterisk is containing libpri? In other words, how can I

Hi All; How to let the virualbox (ubuntu OS) to be able to see the digium card? Because when I install elastix or asterisk with dahdi, it is not able to see the digium card if the installation though the virualbox .. What is the solution? Regards Bilal

Dear; Thanks a lot for guiding me. Is it possible that the installation libpri-1.4.11.5 newer than the libpri-1.4.11.5-patch? Well, when I typed (note: I am trying to apply the libpri-1.4.11.5-patch for the libpri-1.4.11.5): libpri-1.4.11.5# patch -p0 -i libpri-1.4.11.5-patch It gave me that patched detected as shown below (example of one file, and I got same for other files): patching file

Dears; To patch libpri: I just place the patch file in the libpri source directory and then I run make and make install? Or I need to compile the dahdi and asterisk also? If the problem stayed, do I have to go for previous libpri version? Or for previous dahdi version and asterisk version? Regards Bilal ----------- > bilal ghayyad wrote: > > But I am afraid it is a bug because I

Dears; I am facing the following problem: Already we requested from the service provider to enable the auto jumping service for our analoge telephone lines, so because we have 4 telephone lines from the service provider, then if you called line # 1 and it was busy, then the call will be sent to any available line #2 or #3 or #4, and if you call line # 3 and it was busy then the call will be sent

Hi All; My ISDN was working fine, and suddenly I start getting the below: sig_pri.c:985 pri_find_dchan: Span 1: No D-chanannel anyway! There is a Yellow Alarm, so what it could be the problem? My configuration as following: system.conf span=1,1,0,ccs,hdb3,yellow bchan=1-15,17-31 dchan=16 chan_dahi.conf context=IncomingPSTN group=0 signalling=pri_cpe switchtype=euroisdn

Hi All; To overcome the echo problem, what mainly I have to do in the configuration other than the following line in the system.conf under dahdi directory? echocanceller=mg2,1-16 1) How can I know if the digium card supporting echo cancellator? 2) If I am getting a message in the consol that unable to enable the echo cancelator, then what does it means? The hardware is not supporting echo

Hi All; When the call coming via the E1 dahdi and I handle the call (as first step) by exten => 5631040,1,Goto(OrangeCMG,s,1) it is not working and the call will be disconnected instead of queued. But, when I handle the call (as first step) by playing any sound file and then send for the queue, then it is working fine, WHY? exten => 5631040,1,Playback(WelcomeMessage) exten =>

Hi All; If I need to set the opermode to King Saudi Arabia, what the name I have to use? For example, to set it for kuwait then I use opermode=KUWAIT. So what will be for Saudi Arabia? Any advise? Regards Bilal

Dears; The problem was related to something else. The Digium card has two PRI ports, actually to get it UP, I have to configure the two ports and both of those two ports to take the timing from span 1. Why this, I do not know ! Although I am using only one E1 connected to span 1, so why I have to configure the other span !! After configuring the second span, so now one D channel for span 1 is

Hi All;

Hi All; I noticed in the queues.conf the configuration for recording the calls in the queuing, and regarding to the filename (or any other parameter), it is written that I can determine the filename using the command: Set(MONITOR_FILENAME=foo) But it should be called from the dialing plan, but really i did not understand how to call it from the dialing plan. Well, for example this is my

So, tweaking configs, rebuilding this and that... restarting, twiddling, it works (yeah!), but fails on re-boot to work at all. Consistently, though. I believe it comes down to this: I can call out only *after* I've received a call. So, cold boot. Then: modprobe dahdi modprobe wctc4xxp modprobe wcfxo dahdi: Telephony Interface Registered on major 196 dahdi: Version: 2.1.0.3