similar to: Slightly OT: PCIe x16 card in x8 slot

Hello! Does TE110P (a 32-bit PCI) fit into PCI Express x8 slot? I'm thinking of buying a Sun X2100 and it has a PCI Express x8 slot. Or perhaps, does Digium produce PCI Express E1 cards? Thanks in advance!

A Regards, Michael Duvall Systems Analyst Concurrent Computer Corporation 2881 Gateway Drive Pompano Beach, FL 33069 c: 954-531-4538 o: 954-973-5395

I have finally received and am configuring my new workstations eith the NVS510 graphics cards, and have run into rather a problem. The X server seems to be loading the NOUVEAU driver properly (based on the contents of Xorg.0.log), but I have one X11 application that doesn't work correctly; it runs as though XSynchronized is always True, even though it's explicitly set to False in the

Hi Guys, In a bit of a pickle.. Is anyone running the latest "Centos 5.9" or earlier version with an Intel X79 based motherboard. I have a server which needs the motherboard replacing asap and I have a spare "Sabertooth X79". I have a machine with a "Sabertooth X79" motherboard to test on which boots up fine on on "Centos 5.9 i386" image from the

I'm looking for direction to install and boot CentOS 7 from an iSCSI device. Any experience and advice will be greatly appreciated. Thanks! Michael Duvall

http://defect.opensolaris.org/bz/show_bug.cgi?id=871 Summary: ''zpool key -l'' core dumped with keysource=hex,prompt and unmatched entered in Classification: Development Product: zfs-crypto Version: unspecified Platform: Other OS/Version: Windows Status: NEW Severity: minor

Quick question that I haven't been able to find the answer to (and not for lack of trying, believe me): Is dual-monitor display for the new Intel HD Graphics 4600 (Haswell, e.g. Intel E3-1200v3 family processors) supported in CentOS 6.4? In particular, I'm looking at a SuperMicro X10SAE; SuperMicro has already replied that triple-display only works with a VGA-HDMI-DP combo (lame) and only

I am sponsoring this fasttrack for John Levon. It is set to expire on 3/14/2007. Note that this is an externally visible case. liane --- SMF services for Xen 1. Introduction This case introduces the SMF services used by a Solaris-based domain 0 when running on Xen, or a Xen-compatible hypervisor. All of these services only run on domain 0 when booted under Xen virtualisation.

So, after some discussion of our new control workstations, we are iterating in on a solution; we are looking at a 1U short-depth SuperMicro SuperServer 5017R-MF with a graphics card in the PCI-Ex16 expansion slot. However, the display requirements have increased to 3 or more monitors for future expansion, so I was wondering whether anyone had any experience with triple- or quad-display single card

Hello Everybody! I am currently setting up an Asterisk server for medium to high load (approximately 20-35 concurrent phone lines). Do you think the following specs will sufficiently satisfy this system? CPU: XeonQC3220 2.4GHZ 8M RAM: 2X2GB/800 Harddrive: 1X250GB I could add harddrives and partition them into /var and /log directories to help with diskdrive throughput. Thanks! Elliot

I just came across this problem (on Linux, using OpenSSH 2.9.9p2). Run ssh <host> "tail -f <file> | grep <regexp>" Let it connect, and then hit ^C. If you look on <host>, the tail process has been orphaned, but grep, which was its parent, and a direct child of sshd, is gone. It appears that the immediate child of the sshd (grep) is sent a SIGTERM (on line

I'm replacing a home PBX with an Asterisk server that needs 2 Digium cards (one PCI, one PCIe). Right now I'm just using a spare desktop machine, but it's overkill in terms of size/power/heat/noise/CPU power. Does anyone know any cost-effective alternatives? -- Eric Cooper e c c @ c m u . e d u

Hi all, I've finally gotten around to setting up the netbook that controls my UPS and I would like to make sure that I've got the metacode correct before configuring nut :) Here's what I've got: Belkin UPS F6C120auUNV * Batteries recently replaced * On battery: 24 port switch, PoE AP, antenna power booster, ADSL modem, MythTV server, 19" monitor * On surge

Hi, Does anyone know if it is possible to plug a tdm400p pci digium card into an pci-e 16x slot ? Is there a possibility to work? I have a sun fire x2100 which doesn't have pci slots. Does Digium make pci-e cards?

Dear All, Hypervisor: Xen 4.0.2-rc1-pre pv-ops dom0 kernel: 2.6.32.26 Distro: Fedora 11 Linux x86_64 Graphics card: NVIDIA Geforce 8400 GS PCI Express x16 Motherboard: Intel Desktop Board DQ45CB I have applied patches from Tobias Geiger''s xen-devel mailing list thread (http://lists.xensource.com/archives/html/xen-devel/2010-05/msg00441.html) to Xen 4.0.2-rc1-pre. VGA Passthrough to

Dear All, Hypervisor: Xen 4.0.2-rc1-pre pv-ops dom0 kernel: 2.6.32.26 Distro: Fedora 11 Linux x86_64 Graphics card: NVIDIA Geforce 8400 GS PCI Express x16 Motherboard: Intel Desktop Board DQ45CB I have applied patches from Tobias Geiger''s xen-devel mailing list thread (http://lists.xensource.com/archives/html/xen-devel/2010-05/msg00441.html) to Xen 4.0.2-rc1-pre. VGA Passthrough to

Hi all, I''m planning a rig that has SuSE linux in Dom0 and Windows7 in a DomU with the PCIe video card passed through to the Win7-U and an AMD system''s onboard video for the Linux system. Couple xen-newbie questions: does my plan work in such that I intend to have the onboard video''s DVI and the video card (at present an NV GTX-460) on the same monitor and switch

Hi, I am starting to use Mapstraction with the openlayers provider, and I am not sure how to retrieve the current center of a map in a cross-provider way. i.e. currently when calling map.getCenter(), the result returned is the openlayers internal one, not the long/lat used when calling setCenter(). Is that the expected behaviour? Regards, Philippe -------------- next part -------------- An

There are a bunch of us working on LLVM in Austin. So we're organizing a LLVM Austin Social in September. The social will be on Wednesday, September 12 from 5 pm at the BB Rovers Cafe and Pub. It'll be great to meet up with folks in Austin who are also interested in LLVM. Please reply and let me know if you plan on attending so that I can get a count. BB Rovers is on Jollyville road

Dear R users, I have a problem computing time differences using R. I have a date that are given using the following format: 20080620.00, where the 4 first digits represent the year, the next 2 ones the month and the last 2 ones the day. I would need to compute time differences between two vectors of this given format. I tried around trying to change this format into any type of time serie