similar to: adaptec RAID

Hallo, has anyone a hint how to use an Adaptec RAID 51645 under Centos 7? A volume is created using the controller interface but isn't active under centos. Thanks for hintsts Ralf

Greetings all. I'm new to the mailing list. Hope to get to know many of you. I'll jump right in with a recent project. I have a machine with RHEL WS 3 - Taroon; plus dual boot to Win 2000 Pro. The RAID card is Adaptec's 2400A w/128 megs cache, running RAID 10 on 4 WD's. I want to migrate to 5.2 Centos and wipe the NTFS partition. I have the 5.2 Centos DVD. Anyone see any

Hi, I've installed a FreeBSD (stable 9.2) as a guest on ESXi 5.5. I've added Adaptec Controller via passthrough. Unfortunately FreeBSD does not show hard drives. Any clue? aac0: <Adaptec RAID 5805> mem 0xfd200000-0xfd3fffff irq 18 at device 0.0 on pci3 aac0: Enabling 64-bit address support aac0: Enable Raw I/O aac0: Enable 64-bit array aac0: New comm. interface enabled aac0:

Hi All, I need to install CentOS 4.0 x86_64 using Adaptec ASC-29320A with HostRAID enabled, but it seems my card isn't recognized. I've tried to install the hardware using driver downloaded for RHEL 4.0 from the Adaptec Website, but still it's unrecognized. P.S. I'm able to install RedHat 9.0 using this card before. Is there anyone have any solution for this? Thanks and

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 1) Has anyone been able to get their AIC-9410 controller recognized in CentOS 5.3? I'm working with a Supermicro X7DBR-3 motherboard. It has 2 "ICH Raid Codebase" options in the Bios (Intel and Adaptec); neither of which seem to change Linux's behavior. The interesting part though, choosing either Adaptec or Intel, then performing

I am posting this as I was researching an issue with my Adaptec 2200s controller, where I would get command timeouts on the controller under heavy constant load (either using rsync or ncftp to mirror folders). I noticed some interesting information that Scott Long posted about issues with 4GB RAM and the firmware. Well, I have 4GB of RAM, and a SuperMicro X5DPL-iGM mobo (intel 7501 chipset), and

I have just built a new SunFire X4100 server with an Adaptec 2230SLP RAID card using FreeBSD 6.2-PRE kernel (from September 20). Everything is working extremely well except I cannot run the aaccli utility on this controller. When I try to open the controller, it gives this error: Command Error: <The current AFAAPI.DLL is too old to work with the current controller software.> On

Hi I got a new Adaptec 6405 card with a set of new harddrives. Problem that I assumed that the card had kernel drivers, which it has but only from 2.6.39 onwards. I installed the kmod-aacraid drivers, they see the card and drives, fine. However, I need to get a "linux rescue" to work, thus I need to load the drivers during the boot of the resuce disk. How do I do this? thanks Jobst

Hello everyone, I'm trying to install the CentOS 4.4 Server CD on old hardware. The hardware is a Dell PowerEdge 2300 with Adaptec 7890 and 7860 controllers. It's the first time I've done a Linux install with hardware RAID. However, I'm having trouble getting CentOS (as well as Fedora Core 6) to detect the SCSI hard drives. When it comes to the part where you choose where to

Hi, We've got a setup here with a samba server in front of a fibrechannel array. It's a pretty vanilla samba setup exporting an xfs filesystem. The box is an opteron 265 with 4G RAM and a QLogic QLA2312 HBA running SLES9. We can dd an 8G file to a share from a windows workstation in just over 2 minutes (about 65MB/s) and dd back in about 4 minutes. Local disk performance in the machine

Hi. I''ve used ghost for change the ide disk for an array of scsi in raid using an adaptec controller 2110s. Now when I boot it didn''t boot correctly. Looking for in Internet (http://kbase.redhat.com/faq/FAQ_46_4969.shtm) I guest that I have to rebuild the initial ramdisk to contain the proper kernel modules for the adaptec controller. But what is the kernel module for

Hi, for a specific application we need a low-profile SCSI card (PCI) with external 50pin connector. I thought about getting an "Adaptec SCSI Card 2930LP". However I was not able to find any usable information about wether this card is supported by Linux/CentOS 5.x or not. Does anyone have this card working with a CentOS 5.x machine? Alternatively: Are there any linux-supported

I need a SCSI card to attach a tape library to my system. I am looking at the Adaptec 29320A-R. Can anyone confirm that this card will work with the stock CentOS 4 kernel? -- Bowie

I have a Supermicro SuperServer 6025B-3V with their X7DB3 mobo. It has an onboard Adaptec SAS RAID controller and has been configured as a RAID1 with two Seagate Cheetah 15k.4 disks. Original attempts at installing CentOS4.4 x86_64 appeared to load the aic94xx driver, but then reported something like "No hard drives found...". I grabbed the x86_64 aacraid driver disk from Adaptec

I'm trying to install the Adaptec Storage Manager for the 21610SA SATA RAID controller on Centos 5.5. rpm reports that it failed on the dependency on libstdc++-libc6.1-1.so.2 yum provides */libstdc++-libc6.1-1.so.2 reports no matches found How can I install the required files to all the Adaptec Storage Manager to be installed?

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all, I've got a server that I'm rebuilding and I've been given an Adaptec 2100S single channel scsi card to use. Problem is I can't find drivers for CentOS 4 anywhere. So far I've tried the adaptec drivers on the install CD but when it comes time to use disc druid it doesn't see the array that I've setup. don't

Okay, this is probably a stupid question, but here goes: We've got a database server that I'm going to wipe clean and install the latest OS. It's running 2.1 right now, and it has a hardware raid. I've found lots of stuff on software raid tools, but are there any tools on hardware raid? We've got another box, an IBM AS/400, and when one of it's raid disks fail

Can anyone tell me if/when the Adaptec AIC9410 SAS/SATA controller will be supported? Michael Grant

Hi there, I'm in the process of installing Centos 5.2 on an IBM x236 w/ ServeRAID 7k I recently acquired to act as a samba file server. The hardware has all passed various stress tests I could throw at it so we're okay there. My question is. Has anyone had any luck getting the latest IBM ServeRAID Manager v9.0 working in CentOS? If so how? ServeRAID Manager is based off Adaptec's

Hi everyone. Some body knows why my instalation always says Could Not mount root device (0,0), then reboots, i try to compile my own dom0 kernel, but always says the same thing. I''m seeking on create the initrd image, but nothings works. :( The currently hardware profile is this. Intel Server Board SE7230NH1-E (VT Enabled Motherboard) Intel Pentium D 830 CPU (3Ghz x 2 CPU) 2 GB