similar to: how send calls to gatekeeper?

hello every one, i have an asterisk system and want to act as gateway and send calls to cisco gatekeeper. this is my h323.conf file: [general] port=1720 binaddr=192.168.0.YY context=from-trunk faststart=yes h245tunneling=yes gatekeeper=192.168.0.XX //cisco address progress_setup=8 progress_alert=8 dtmfmode=rfc2833 jbenable=yes jbforce=no jbmaxsize=200 jbresyncthreshold=1000 jbimpl=fixed jblog=no

All, I'm running (attempting to) ooh323 with Asterisk and a Cisco 2621XM router operating as a H.323 GateKeeper, however when I bring the Asterisk box up it registers successfully with the GateKeeper (exchanges GRQ/GCF, then RRQ/RCF) it notes the GateKeeper supports keepalive at 300 seconds, when it gets to time to re-register its sends an RRQ again and gets rejected with RRJ (unspecified

All, I've fixed my problem getting Asterisk ooh323 channel to stay registered with my Cisco IOPS gatekeeper, now I need to get dialling working. I have the following: [Asterisk with ooh323] ----h323---- [Cisco IOS GK] ----h323---- [Radio system OpenH323] 192.168.1.5 192.168.1.6 192.168.1.7 the Asterisk box has numbers

Stephan, Ok, I'll re-state the problem... I have two devices that I want to talk to each other: 1. an Asterisk PBX 2. a Damm Cellular TETRAFLEX digital radio system (www.damm.dk) both devices are effectively "gateways" because they have many subscribers behind them. The Damm Cellular system controller is based on Windows-XP Embedded and its sub-systems used the OpenH323

All, I'm haveing a bit of trouble getting my head around H.323 and call routing with Gatekeepers, Zones and intra-zone calls - hopefully someone who is more informed in things H.323 will be able to point me in the right direction...? I already have a mature network of Asterisk boxes dotted around the UK and overseas with hundreds of extensions and our own number-plan/dial-plan in the form

Hi, I am testing asterisk in several situations, I still can not understand why we have to deal with two different h323 channels... Here is the problem, I have a cisco 3700 who sends h323 calls to asterisk. then I process the call upon several users parameters, and send it to another cisco gateway. All the transactions are made in h323. I first tried with h323 channel, and had no audio... I guess

Hi, I am trying to communicate H323 and SIP users. I have configured h323.conf, sip.conf and ooh323.conf. If I am using gatekeeper (gnugk) then I am able to call successfully to h323 users using SJphone. And same for SIP users also. But when I disabled gatekeeper and trying to call using gateway with sjphone then every time whatever number I dial the call goes to asterisk and some computerized

After much reading and fiddling - I have the gnugk GateKeeper running and can make calls from the H323 phone to the sip phone. Voice works bi-directionally.. Calling from SIP to H323 gives me a problem... Both gnuGK and Asterisk are on the same box. Someone said this was OK. Others said No. I added a second IP (eth0:1) and told gnuGK that was HOME. How do I lock asterisk to the other (eth0) IP -

Hi all, i have tried to connect to a clarent gatekeeper. I have used both of h323 drivers chan_h323.so and chan_oh323.so. But no one can register to this gatekeeper. Our ip is activated on this gatekeeper. Maybe, i do wrong anything.... I have only set the "gatekeeper" option in the h323.conf or oh323.conf to the ip address from the gatekeeper. gatekeeper=x.x.x.x But no one of the

Hi list, After several tries to understand the subtil description in the h323.conf to be able to make the next scenario I was presented the following error messages by asterisk. Can somebody tell me please what I am doing wrong. Scenario: Gatekeeper (h323) --> Asterisk PBX -->(h323) Gateway Endpoints are connected to Gatekeeper. Call does come in like 999931235650087 with codec g711

Hi everybody, I have still problem with setting-up asterisk. I use asterisk with gnu gatekeeper and h323 phones. I read lots of much documents, but there's no any reference to setting-up "how to put on hold an incomming call". I mean: 1.) somebody call me from PSTN (via my ISDN BRI card in asterisk); 2.) asterisk routes this call to gatekeeper and finaly I pick up call by my

Hi. I'm using Asterisk & oh323. My gatekeeper needs h323 ID and e164 ID for registration. But I don't know how to send e164 ID. I configure register section in my oh323.conf file like below. [general] <<snip>> gatekeeper=xxx.xxx.xxx.xxx [register] alias=abc alias=777 <<snip>> And the gatekeeper doesn't need passward. It authenticates to use only both h323

Hello All Anybody had used ooH323 for asterisk i using ooH323-0.7.2 and asterisk CVS may 2005. OpenH323 1.17.1 and pwlib 1.9.0 and GNUGK 2.0.2 audio is very good, better than SIP and IAX, but i have problem. how to router call from openh323 to outside PSTN. my h323.conf setting ; Objective System's H323 Configuration example for tvcti ; ooh323c driver configuration ; ; [general]

OOH323 Debugging Enabled -- Executing Answer("SIP/3513-090f7d40", "") in new stack -- Executing Wait("SIP/3513-090f7d40", "1") in new stack -- Executing DeadAGI("SIP/3513-090f7d40", "a2billing.php|1") in new stack -- Launched AGI Script /var/lib/asterisk/agi-bin/a2billing.php a2billing.php|1: line:58 - IDCONFIG : 1

hello all, i want to have ooh323 connection between asterisk and cisco. in my scenario, asterisk is gateway and cisco is gatekeeper. this is my ooh323.conf file: [general] port=1720 bindaddr=192.168.0.227 gateway=yes faststart=yes h245tunneling=yes h323id=gw10 at test.com settracelevel=10 gatekeeper=192.168.0.212 context=from-trunk disallow=all allow=ulaw allow=alaw allow=gsm dtmfmode=rfc2833

Hello there I'm quite a newbie in the IP Telephony area. I'm playing a little around with a setup with one linux box with a e100 p card installed, which functions as an Asterisk gateway and a oh323 GK(Gnu Gatekeeper). I have two h323 phones, Welltech WellGate 1501 and 3502. So far I've managed to get the two IP phones and Asterisk connected to the GK. I can place calls from one

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi there, i have a working Microsoft ISA firewall with buildin H.323 Gatekeeper.... So Far, i got registerd the asterisk on the M$ Gatekeeper... here is the h.323 configuration: ; Open H.323 driver configuration ; [general] port = 1720 bindaddr = 0.0.0.0 allow=all ; turns on all installed codecs dtmfmode=rfc2833 gatekeeper =

I'm having trouble registering my asterisk to a cisco gatekeeper. I do not have control over the gatekeeper, and I know that it has user info defined in an LDAP. I have a user name and a password that I can use, but I can't seem to get Asterisk to register on the gatekeeper. I can't find exactly how I'm supposed to define the gatekeeper in the h323.conf file. This is the response

Hi all, I have one asterisk server with one ISDN BRI connection to PSTN, with h.323 support (oh323) I buy some voip phones, and I connect them to the same switch as asterisk server is; all is at the same TCP network. I need to route some extensions from my DDI (DID) line at asterisk to some voip phones, and also to do: outgoing calls from any voip phone to PSTN via asterisk, and intermediate

Dear friends, I have compiled and installed h.323 in my asterisk. And I have a service from a H.323 VoIP provider who give me user, password and gatekeeper IP address. All configured. But when I start my asterisk i receive the following error and h.323 calls can not be making and/or receiving. [chan_h323.so]=> (The NuFone Network's Open H.323 Channel Driver) == Parsing