similar to: Network configuration question

Hi, I'm a 40-year old sysadmin living in Montpezat, a small village in the sunny south of France. I'm a Linux user since 2001, when I made my first steps on a 486 with a Slackware 7.1 CD. I've tried maybe two dozen distributions, but I've stayed mostly with Slackware and Debian. Since last summer, I work as a sysadmin for our "Communaut? de Communes", a group of 16

Hi, I'm just migrating some stuff from Slackware Linux to CentOS, and I have a question about the orthodox way of configuring a network connection. On a desktop or workstation, I usually get rid of NetworkManager: # systemctl stop NetworkManager # yum remove NetworkManager Then I edit the /etc/sysconfig/network-scripts/ifcfg-XXXXX file corresponding to my network interface. Here's

Hi, I have CentOS 4.3 installed on my Fujitsu Siemens Amilo D laptop (Pentium IV 2.4 GHz CPU). Everything runs just fine, but I have one problem. When I leave the machine unattended for something like an hour or two, my desktop has "frozen". Unable to recovery anything, even [Ctrl] + [Alt] + [Backspace] refuses to quit X, so I have to hard-reboot by pressing PowerOn/Off for 10 seconds.

Which is the best laptop to run centos on and where can I buy one without Windows Vista pre loaded cause I will uninstall it any way. Please tell me the best sites that ship worldwide.

ClarkConnect Home 3.2 eth0 - WAN - inet - ip:192.168.1.2 gw:192.168.1.1 (connected to my www.woosh.co.nz gatway) wlan - WAN - private community wireless networt - ip:10.252.16.16 gw:10.252.16.1 eth1 - LAN - ip:192.168.2.1 # route add -net 10.0.0.0 netmask 255.0.0.0 gw 10.252.16.1 [root@bowenvale etc]# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface

Hi all, After having read most of the available documentation I still have got problems interconnecting two networks in router mode: My configuration consists of two private home networks that I want to connect: Vienna 192.168.0.0/24 - Internet gateway 192.168.0.1 Berlin 192.168.1.0/24 - Internet gateway 192.168.1.1 VPN Devices are configured as 192.168.3.1 (Vienna) and 192.168.3.2

HI I admit up front that I know just enough about wireless networking to know that I don't know much at all about it. That said, I'm hoping someone can help me learn a little bit... Specifically, could a laptop running Centos 5.1 be expected to (be able to) connect to a wireless access point using WPA2 security settings? I don't know if WPA depends on hardware support, or if

> > Of course, to be fair, there may have been a *reason* for not doing it > that way before.... > Between the early 1990's and early 2000's the price of a GB of memory went from ~$100,000 to ~$1000*. I guess a lot of the design decisions made for things like init were focussed on this. In 1995 is was common for server platforms to have 32Mb ram whereas the kernel alone in my

Hello everyone! How are you? Hope you''re well :) Here''s my setup at home: Internet -> (eth1) Comp1 (shorewall, DHCP, dns server, Internet sharing) (eth0) -> Linksys (wireless) ~~~~~~~~~~~~ (wlan0) Comp2 (eth0) -> IP Phone My computer1 is well confiugred, everything was working right and well. I decided to move the IP Phone to the COmputer 2. I was able to make this

I'm trying to bridge a wired network and a wireless network, but I'm having some trouble. No traffic seems to be passing through the bridge. When I issue a "showmacs" command to brctl, I am able to see MAC addresses from both networks. I am also able to ping both networks from the bridge machine. When I issue a "showstp" command to brctl, the wireless access

I just installed an Asus PCE-n13 wireless card into one of my CentOS 5.6 systems. It uses the RaLink 2680 chip set and I was able to get the driver loaded using modprobe rt2x00pci.ko. I saw no error and now see that the module is loaded along with mac80211 and other dependencies. Now I need to know how to create the wlan0 device. I can find nothing via Google searches on how to create that

I am having problem in ping or connect AP from Mobile Node(essid & channel is the same,maybe routing did not set properly but i fail to configure with route add default gw 192.168.3.4,its alway said network is unreachable ),My Mobile Node is using acx100 as driver while AP(redhat 9.0) is using HOSTAP 0.1.3.Any one can help? I heard How-To said we not need to set address on eth0 & wlan0

Hello good day to all ... this is my setup 1 Linux Wireless Access Point, connected are 4 wireless gateway in which i needed to apply shaping ... ok here is the weird part... clients on each gateway download files from the Acess Point ... a 500 mb file through ftp on gateway 1 which is up to 64 kbps ... the result is from 60-64 kbps speed which is fine ... on gateway 2 which is 128 kbps ... the

I have an Everex laptop (ick, but it was super cheap) that has an Atheros wireless NIC in it, but I can't seem to get it to connect to my wireless in-home LAN. Here's what I've done so far (that isn't working) - any suggestions? [root at marktop mark]# lspci | grep Ether 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 7c) 05:01.0 Ethernet controller:

I know, I know... don't use the non-standard kernels unless you have to... BUT: I have a D-Link N150 USB card. Bus 001 Device 004: ID 0846:9030 NetGear, Inc. WNA1100 Wireless-N 150 [Atheros AR9271] This isn't supported in C5, but it is supported in newer kernels (ath9k_htc). So let's try NDISwrapper: # rpm -i kmod\-ndiswrapper\-1.56\-1.el5.elrepo.i686.rpm

On Thu, Mar 30, 2017 at 06:15:28PM +0100, Nux! wrote: > Use libvirt with mac/ip spoofing enabled. > > https://libvirt.org/formatnwfilter.html > > https://libvirt.org/firewall.html > > -- > Sent from the Delta quadrant using Borg technology! > Thanks Nux and Kristian but I don't see if these solutions will be really efective in my environment. Let me to explain.

Hi, I have a wireless network but no wired network. I need to access the net for the necessary installation of the wireless drivers in CentOS 5.1. Could anyone let me know how i can go about it!! My card is Intel PRO/Wireless 3945 -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, The pc that runs the samba server is my own property, it also dubs as router and dhcp server. I assign WINS server to the clients by dhcp using dnsmasq. I do not need or want to setup a domain. I just want to share files between the two networks using windows neighborhood and a workgroup, just like the clients would have been connected in the same network. I have deleted the "remote

Hi all, I'm trying to configure wireless on my Asus laptop running CentOS7. I see wlan0 when I type iw dev, but if I type ip link set wlan0 up I get the following error: RTNETLINK answers: Operation not possible due to RF-kill Any idea what is wrong?? Adrian -- Adri P. van Bloois Antonlaan 104 email: adrian at pa0rda.nl 3701 VG Zeist voice: +31-(0)-30-6912741 The Netherlands fax:

On a CentOS 5.5 laptop (Dell Inspiron, dual boot with a Debian-based distro) I have a cable plugged into eth0 which is on a LAN with no internet connection. Additionally, I connect wirelessly on wlan0 to the internet. Both connections have router on the 192.168.0.1 address. Although I need to stay connected to the wireless router, can I still access the address 192.168.0.1 on the wired