similar to: (no subject)

Hi all! I just started to experiment with bandwidth management using tbf. I have the folowing problems with token understanding: 1) What unit is token? Is "1 token = 1 byte" ? If this is so, then with rate=0.5mbit and HZ=100 the bucket gets filled with 0,64kb (655 tokens) every 10ms? 2) How much tokens are used for one packet (1500)? 3) And token unrelated question. Does

Hi have set the following tbf tc qdisc add dev eth0 root tbf rate 0.5mbit \ burst 5kb latency 70ms peakrate 1mbit \ minburst 1540 I want to add a filter so the ip traffic pass from it.. plz help me __________________________________ Yahoo! Mail Stay connected, organized, and protected. Take the tour: http://tour.mail.yahoo.com/mailtour.html

Hello all, My company is sharing it''s internet access with a neighbor and the neighbor in question was eating our bandwidth (both in upload and download) most of the time. I finally set up a linux router to limit the incoming/outgoing bandwidth to his network by adding a tbf on eth0 interface and eth1 interface of the router (neighbor is behind eth1 and we are in-between him and the

Hi, I have a basic router that is shaping traffic, and it seems to be working at the moment. We have a 100Mbit connection to the internet, however we get charged for each mbit that we use and so have to shape/limit the traffic to avoid huge bills and my boss getting cross!! We have a /29 subnets set up as follows: tc qdisc add dev eth0 root tbf rate 0.8Mbit latency 50ms burst 10k tc qdisc add

Hello mailing list, i stand bevor a mystery and cannot explain it J. I want to do shaping and prioritization and I have done these following configurations and simulations. I can´t explain, that the combination of PRIO and TBF is much better than the HTB (with the prio parameter) alone or in combination with the SFQ. Here are my example configurations: 2 Traffic Classes http (80 = 0x50) and

Hi, Having issues getting a replace command working correctly. The error reported is "RTNETLINK answers: Invalid argument" which isn''t descriptive or helpful. The command i''m running is: tc qdisc replace dev ppp0 parent 8001:D handle D: tbf rate 5Kbit burst 5kb latency 70ms The idea being to replace an sfq with handle D and hopefully limit a certain user in my

I''m just-so-fresh to the list, so hello everyone. I''m having a realy hard time with setting up very simple bandwidth management. What I am trying to do is setup a 10Mbit interface to send at only 1920kbit to most of the network (to make sure it hardly ever tops 2mbit). I did succeed with the ingress traffic... With egress however, I get very odd results at different speeds. With

Hello , I tried a simple test as follow : I used vmware software to set up 3 virtual linux computers . The middle computer act as a router (rip protocol ) using zebra software . I used iperf-1.7.0 to generate traffic from linux computer 1 to linux computer 3 . At router ( egress side ) I setup a simple qdisc as follow : tc qdisc add dev eth1 root handle 1: tbf rate 0.5 mbit burst 5kb latency

About the cbq.init. Four machines which traffic to limit in same LAN. Is the samething if I put limiting rules to four different files or all to the same file? Like: DEVICE=eth0,10Mbit,1Mbit RATE=64Kbit WEIGHT=6Kbit PRIO=5 RULE=192.168.0.5 RULE=192.168.0.6 RULE=192.168.0.7 RULE=192.168.0.8 OR four equal files with different IPs, Ids and no PARENT rule? What style of ID numbering you use if

lartc-request,hello! 　　 I find a line in tbf_change() in sch_tbf.c: ptab = xchg(&q->P_tab, ptab); Can I consider that the pointers are exchanged between q->P_tab and ptab? as following: prev=q->R_tab; q->R_tab = rtab; rtab = prev; Is my understanding righ? ======= 2002-03-23 12:01:00 you wrote:======= >Send LARTC mailing list

Hello. Sorry for my poor english =) I have following config for traffic prioritization: tc qdisc add dev eth0 root handle 1: prio tc qdisc add dev eth0 parent 1:1 handle 10: tbf rate 7000kbit buffer 1600 latency 2msec tc qdisc add dev eth0 parent 1:2 handle 20: sfq tc qdisc add dev eth0 parent 1:3 handle 30: tbf rate 3000kbit buffer 1600 latency 50msec tc qdisc add dev eth1 root

Hi all I''m new to this list, but not exactly to iproute stuff. I''d like to solve a specific problem with bandwidth coming from different external sources towards the internal network (also the other way around, but I figure that''s not so much a problem, since that is egress traffic shaping). The network looks like this: internet ------ ISP-------[shaping/router]

I''m trying to fill a token bucket with enough tokens to burst several gigs of data. However, it doesn''t seem to get any higher than ~3.9GB: >tc qdisc add dev eth0 root tbf rate 1440kbit latency 50ms \ burst 16000000000 >tc qdisc show dev eth0 qdisc tbf 800b: rate 1440Kbit burst 3908420240b lat 2197.8s A smaller attempt of ~1.6 gigs works just fine: >tc qdisc

I have htb on 486 sx with 16mb ram. Slackware 9.1. Connection : dsl 1Mbit. 486 works as router and trafic shaper for network made of 12 pc''s. it does the job quite well, but when i play Counter-Strike or connect to my 486 via ssh (on lan), i get huge lag every 11-20 sec. when i connect to 486 via ssh and run iptraf program i see all the trafic, and after a while when lag comes the

Hi i have found a problem related with tbf and the latency that the tbf calculates.. I have used the following parameters for burst and limit burst 100Kbit limit 500Kbit lat81.8ms burst 6Kbit limit 6Kbit lat 0us burst 200Kbit limit 100Kbit lat 4294.9s As u can see in the 3rd column the latency for 100Kbit burst and 500Kbit limit is 81.8ms but for 200Kbit and limit 100Kbit is 4294.9s!!! How

Hi All, I want to setup a machine to connect to internet at a limited rate of 64 kbps. That machine is connected to a switch. so my LAN and Internet both comes from the same eth0. How can I limit only the internet access from this machine to 64kbps and still using 100mbps for LAN I am trying to implement this Please guide me If i am wrong. I mark all the packets going out to LAN. Then I can

Hi Everyone, This is a simple question but I don''t understand why the below tbf is not working as expected by throttling traffic to 5kbps If I throttle a PC''s traffic using the below when traffic exceeds 5kbps packets start getting dropped (as they should) but all traffic gets dropped. not just the bit over 5kbps. TC="tc add dev ppp0" $TC parent 8001:2 handle 2:

I am using tbf to do rate limitation. i set the rate, burst and latency parameters for tbf. but when i start passing data i notice that there is an initial burst and then the rate goes down to the configured level. is this because tbf starts with a full bucket? thanks. __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection

Dear friends, thanks for the last advices about TBF. After reading the tbf.pdf document I got a better insight of the problems I had trying to limit the bandwith on my testbed with a high resolution. The question I have now is: Would I get an immediatly better resolution result if I change the #define HZ to 1000 for my Linux box? I have a Pentium Celeron 700 MHz, and I would like to see the tbf

Hi I''m completely stuck with the tcng language - I assume there must be some way to arrange queues hierachically like eth1 | TBF | PRIO / \ class class but my attempt (below) produces a "inferno.tc:8: qdisc "tbf" has no classes near "prio"" when run through tcc. dev eth1 { egress { tbf (rate 128kbps, burst 64kb,