similar to: Dead Gateway Detection

Hello all! I applied http://www.ssi.bg/~ja/routes-2.6.8-10.diff patch to kernel 2.6.8.1 and it works fine, or almost fine. It does the load balancing well, but when one link is dropped it continues to try it. At the end of http://www.ssi.bg/~ja/nano.txt it is said to ping gateway 1 and gateway 2, for the kernel to know if that route is working, but since my linux is connected to the links

Hello r helpers! Below is the whole coding for my programme. Before proceed more further, let me explain for you. First of all, I need to compute trimmed mean. Till that step is ok. Then I need to compute ssdw which is sum of square deviation. If I do equal trimming at both tail of distribution that I chose, I will use the first ssd formulae which is "a". But if I am doing unequal

Hi Who concern, I setup TINC VPN follow these. 192.168.1.x / 24 (Client groups) | 192.168.1.1 (eth1) (GW1) 202.44.34.206 (eth0) || Internet || 202.44.45.14 (eth0) (GW2) 192.168.2.1 (eth1)

I have both cable and dsl service. The router attached to the cable service is 192.168.0.1 and the router attached to the dsl service is 192.168.0.254. I determine which service my computers communicate through by setting the gateway assignment to either of those addresses and it just works. I can connect to my computers from the outside by port forwarding from my routers to the computer that I

Hi, I've searched the archive but can't seem to find the answer to my problem. i have two gateways running with asterisk , my question is : is there any possibility to do failover with gateways with asterisk ? i mean that if one gateway is down , asterisk switch automatically to other gateway . i have succefully used failover with limit number off calls (if gw1 have max calls ,asterisk

Thanks for the help, James! its finally working!

I am have a shorewall firewall and freeswan ipsec running on a redhat 8.0 Linux gateway machine. I have one working tunnel defined, all works well. I am not clear how to define mutiple concurrent tunnels. I can not add further interface entries as all the tunnels come in on ipsec0, do I still have mutiple zone definitions? some of the tunnels will be dynamic roadwarriors and as such would need a

Hi all, I have setup two multipath route tables on my system for doing failover routing, What I want it''s that if GW at route1 of the MP is dead, traffic goes by route2, for doing that I have created the multipath routes as follows: ip route add table mail.traffic proto static nexthop via ${GW1} dev eth1 weight 1 nexthop via ${GW2} dev eth1 weight 250 But it does not run as I

I''ve applied julian''s paches to a 2.6.14 gentoo kernel with the appropiate options enabled, and i''m using a modified version of the mpath2.sh script also available on julian''s site http://www.ssi.bg/~ja/ Overall everything works nearly perfectly. Incomming connections to either the fios (PPPoE) connection, or cable modem get routed back out correctly. The

I would like to perform a bootstrap validation of a backward stepwise logistic regression analysis, but I am a beginner with R and I am not sure of how to do it. Is there anyone that can send me a sample file in tab format (that I can modify in Excel by pasting my data) and the pertinent R algorithm? Many thanks Giuseppe -- ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ Dr. Giuseppe Biondi

Hello, I have configured a load balancing router using Julian''s patches and as described in "nano.txt" for two ISP links as shown below. ISP 1 ISP 2 . . | | | | | | | WAN

How do I allow traceroute to reach my server? Pings work fine but traceroute stops at the last hop before my server. If I shut off the firewall it reaches it fine. PING danicar.net (24.222.246.120): 56 data bytes 64 bytes from 24.222.246.120: icmp_seq=0 ttl=237 time=104.0 ms 64 bytes from 24.222.246.120: icmp_seq=1 ttl=237 time=74.9 ms 64 bytes from 24.222.246.120: icmp_seq=2 ttl=237 time=90.6

Hello all. I am not 100% familiar with the Linux advanced routing capbalieties yet, so I thought , after reading source code, documentation and more that I might be better off asking the experts on this list. I am not using this ina production environment, but at home, as a test case. First of all, here is the network topology. Internal LAN <--> Switch <--> [NAT/FIREWALL/INTERNAL LAN

Hello, So installed Fedora15. No problem, wish it had regular menus but the steamline effect isn't totally terrible. Heard that Guild Wars1 is playable in linux and so installed wine. It seems that you aren't supposed to install as root so I removed it as root. I then try to install anything via yum as non-root and I get the error of needing to be root. So, I read that you can bypass this

I''m a little confused about the many ways I''ve read that can be used for traffic load balancing, that is, two or more interfaces to the outside world being used transparently and efficiently by the internal machines. I heard about: a) netfilter SNAT to more than one IP. If I''m correct, this is only a round robin, that is, one connection goes here, the other goes there,

Very soon Guild Wars 2, the MMO we've all been waiting for (right? right!) is coming, and I would like to do my part to make sure that it runs under Wine from day one. Especially as GW1 is one of the top-performing games under Wine. Now I am not an avid coder, but I will pre-purchase the CE, and with it comes access to all the beta events between April 10 and release. So there should be

Hello, I have setup a centos server running 5.5 and I have a problem with the FTP settings. Currently I have two FTP accounts based on that server, they lead to: /home/bella /home/carmen Currently the FPT accounts starts in the home directory when they are logged in. But they are able to see all directories on the server. What can I do to make sure they cant come out of there home directory?

Cristian and Alex, Both of you have asked about this. A routing table can only have one default route so when the second link comes up, adding the second default route will fail. So in general, Shorewall can only reliably detect the gateway for P-T-P connections which is what the CVS current code does. -Tom -- Tom Eastep \ Nothing is foolproof to a sufficiently talented fool Shoreline, \

--Qz2CZ664xQdCRdPu Content-Type: multipart/mixed; boundary="BI5RvnYi6R4T2M87" Content-Disposition: inline --BI5RvnYi6R4T2M87 Content-Type: text/plain; charset=us-ascii Content-Disposition: inline Content-Transfer-Encoding: quoted-printable Hi! Unfortunately there is a very unpopular announcement to be made on this list: A netfilter security advisory. Phillipe Biondi has been

While using the file functions have found a few more issues (on both Unix and Windows) ie R documentation: In the "close" description (base package) we see that the possible values for the mode 'open' the "r+" and "r+b" values are repeated, and are incorrect the second time. The second set actually corresponds to the "w+" / "w+b", see