similar to: Difference between tc reported rate and IPTraf Rate

Hi, I am trying to do both ingress and egress bandwidth management on a bridge. eth0 is the WAN interface. IPTraf shows that the following script is running successfully and it limits bandwidth both ways to 256 KB However when I want to see the statistics using tc - it only shows me stats for htb class and not for ingress class. The tc output is as follows: tc -s -d class show dev eth0 class

I am successfully running ingress (IMQ) and egress (HTB) shaping on a bridge. Is there any way to combine and share the bandwidth between ingress and egress? Example: I have set up www service for egress at 128 KB and ingress at 256 KB. The shaping on them works fine separately. However, I want to create a single virtual pipe for www traffic and limit both ingress and egress combined to 256 KB.

I have a CentOS 4 server at home where we store all our data, I wanted to get some idea of the amount of traffic going into and out of the server by protocol so I installed IPtraf.. When I run it from an ssh session it looks fine but when I run it directly on the server console its doesn't look right at all.. It doesn't seem to layout correctly.. Is there something I need to do

Hi everybody! I am very glad to get htb test information from www.docum.org for the htb performance. Today, I setup a bridge using brctl. my setup as following: 192.168.2.26 | | | |------------- | HTB+BR box |-------- 192.168.2.18 | eth0 | | eth1 192.168.2.29 | | | I want to limit

Hi, In my LAN Iam trying to make following setup: - All the traffic generated by 10.0.2.1 should go to 10.0.2.11, If the destination of this traffic is internet than it should be placed on its interface eth1. Outgoing traffic on eth1 should be shaped.For this I am using fw filters and cbq. _______ 10.0.2.1 -------> 10.0.2.11(eth0 )----| A

Hi all, This may sound strange, but i have a question.. is there any commands which we can use to see the entire TC configurations.. iam new to this TC , thanks, Rajesh Rajesh Revuru, Res:105 smith lane,#33, Syracuse-NY 13210. Ph.315-422-8908(R) Ph.315-443-9120(O) --------------------------------- Do You Yahoo!? Yahoo! Auctions Great stuff seeking new owners! Bid now!

Hello there, Having made quite a lot of expensive mistakes i have finally clobbered together a script for the users on my network. Have a look at it and please suggest as to how can i limit bandwidth to each ip on this network to about 64Kbits. Trevor -- ( >- GNU/LINUX, It''s all about CHOICE -< ) /~\ __ trevor@clovertechnologies.com __ /~\ | \) / Pre Sales

Hi, I''ve migrated my tc configuration from CBQ to HTB. One problem appeared. Htb seems to miscalculate the bandwidth for classes with greater rates. For rates below 2Mbit there is almost no difference between the configured and the measured rate. For large ones the problem starts. My root class has 10Mbit rate and when the interface has heavy trafic the measured bandwidth

Hi, Just wondering, how you guys monitor traffic per ip to test if the traffic shaping is working? iptraf works great but no new version is available, and most ip accounting projects (MRTG & Friends) update its graphics on a per minute process. So I´d like to know which project you use to monitor bandwidth use in real time. Regards, Edo

Hi, I am not been able to contact with mentor of this project. Can someone else from the community help me with this ? Regards, Anusha Srivastava On 3 March 2018 at 11:16, Anusha Srivastava <sidd.sinha89 at gmail.com> wrote: > Hi Martin, > > Any update on this ? > Regards, > Anusha Srivastava > > > On 28 February 2018 at 23:37, Anusha Srivastava <sidd.sinha89

Hi I''ve searched the archive for a solution where I want to limit/shape WLAN users. I only know''s their MAC, because they get their IP from dhcp. > Why not, just use negative offsets with U32 to access >the 14-byte eth frame header before the IP header: > >Decimal Ofs Description >----------------------------------- >-14: DST MAC, 6 bytes >-8: SRC MAC, 6

Is IFB realy replacement of IMQ Please Guide -- Failure seldom stops you. What stops you is the fear of failure. _______________________________________________ LARTC mailing list LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

Hi, I would like to participate in GSOC 2018 with Xorg to contribute to project "Initial Nouveau Vulkan driver' I would need some help in how to get started with the same. Regards, Anusha Srivastava

hi how to check the data rate on the nic card in centos i.e, at what speed the data is transmitted and received on ethernet interface in terms of kbps or bps any command is available in centos 5.1 regards, Gopinath M -------------- next part -------------- An HTML attachment was scrubbed... URL:

I have tried using iptraf for my NAT firewall to analyse the IP traffic. Basically I am faced with this difficulty of related the source IP to the outgoing interface to the internet, so I am wondering if anyone has a suggestion for a different ways to do it, or a suggestion for a better tool. Details :- Supposed : eth0 - LAN eth1 - WAN1 eth2 - WAN2 And then

how to sum columns in R?

Hi, I am using thin web server in my rails project. But it gives stack level too deep error. Couldn''t find any appropriate solution to this. I have tried updating the ruby but didn''t help. Regards, Sumit -- You received this message because you are subscribed to the Google Groups "Ruby on Rails: Talk" group. To post to this group, send email to

Hi, I made a contact manager app using rails. I added TokenInput plugin to introduce an instant contact search functionality in it. Tried following a railscast http://railscasts.com/episodes/258-token-fields but have been struggling with it for a while. Following is the code I use in my view <%= form_tag({:action => ''show'', :id => @contact_tokens}, :remote =>

I want to use snort inline for ips and imq for bandwidth shaping When i have inserted imq module ip_queue module insertion giving error Is it possible to use both at the same time -- Failure seldom stops you. What stops you is the fear of failure. _______________________________________________ LARTC mailing list LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc