similar to: couldn''t get available bandwith

Hi i have configured my server with cbq and gred. The problem is that the cbq doesnt drop packets. The cbq is configured at a rate of 500Kbit "qdisc cbq 4: rate 500000bit (bounded,isolated) prio no-transmit Sent 100103048 bytes 73933 pkts (dropped 0, overlimits 0) borrowed 0 overactions 0 avgidle 24000 undertime 0 " The traffic that being generated is more than 5Mbit with the

I want to set the DSCP field of the incoming packets. And then put them in the correct queues. I can mark the packets: iptables -A OUTPUT -t mangle -d 10.10.10.12 -j MARK --set-mark 1 tc qdisc add dev eth0 handle 1:0 dsmark indices 64 set_tc_index tc class change dev eth0 classid 1:1 dsmark mask 0x3 value 0xb8 tc filter add dev eth0 parent 1:1 protocol ip prio 1 handle 1 fw

Hi, I want to setup core routers to do both DSCP marking and to get the DSCP and forward packets based on DS field. I don''t want to separate DSCP marking to be done only at the edge routers. I know that dsmark is both used for DSCP marking and for getting the DSCP and forwarding packets according to DSCPs. In my case, since I want to do both of these I need two dsmarks.(?) I am not

hi all i am a new commer of linux community. i want to how does skb->tcindex value change exactly. it confused me indeed. i have a script reads: (1) tc qdisc add dev eth0 root handle 1:0 dsmark indices 64 default_index 0x161 set_tc_index (2) tc filter add dev eth0 parent 1:0 protocol all prio 1 tcindex mask 0xfc shift 2 pass_on (3) tc filter add dev eth0 parent 1:0 prio 1 handle 0x0a

Hi, I am trying to get assured forwarding/expedited forwarding with gred and htb working. Below is the script I am using. The following steps are what I thing is how the script works. My problem is that if I remove the HTB qdisc from the script and have the GREDS parent as the dsmark it works, but when I add the htb as a parent of GRED and DSmark the parent of htb it does not work? Any

Hello, I have an OpenVPN running on a system with Samba 3.0.9. However, with this setting (tun2 is my VPN device): interfaces = tun2, lo bind interfaces only = Yes it doesn't bind to tun2, but to ppp0. What the heck? Tomek

Hi. I did send this to `jaazz@post.cz'', but I suspect the list is a more appropriate/useful place for it. It''s a question about Michal Charvat''s QoS extension to Net-SNMP. When I look at the MIB entries for the QoS handles, I get something like this - enterprises.qos.qosObjectTable.qosObject.qosHandle.0.0 = Gauge32: 0

Hi I am encountering what I suspect to be a bug in the kernel processing of tc netlink messages: I am using kernel version 2.4.9 with iproute2-current-001007 package. Everything works fine in the kernel. Now I open a netlink socket with a user process, read the tc netlink messages generated by the tc process and parse them. What I see is that the kernel has already processed the messages

Hi folks I have created a script file (dsmark+policing.sh attached) to check graphic an text outputs of simutations, against original examples/dsmark+policing coding (see TCNG Reference Manual-pg.90). It uses tcng coding (*.tcsim file attached) and old tc coding (*.tcsim_old file attached) inserted in tcsim files. Observation 1: The graphic outputs from (*.tc included in *.tcsim) and (*.tc_old

Hi: Execuse me if this has been mentioned before, I''ve looked around the archive but did not find anything about the problem I met. I''m trying to use tcindex to classify the the packet outgoing to one interface. I do as the following : tc q a dev eth0 root handle 10:0 cbq bandwidth 10Mbit avpkt 1500 tc c a dev eth0 parent 10:0 classid 10:1 cbq bandwidth 10Mbit rate

Hi! I am learning tcng without having experiance of tc and I am trying to build something that shall schedule traffic dependent on the value in the IPv4 packets ip_ttl field. I have read the tcng reference manual and cannot find information about forwarding. Is it possible to farward packets from ingress to egress without sending them upwards in layers?

Im experimenting with using a Linux machine with 3 interfaces to operate as a core router. All links and network interfaces are 100mbit. Below is a ascii diagram of the network. (network A) edge router ------>core router---->edge router (network C) ^ | | edge router (network B) I have tried two

Hi, i've got this problem with my jail and i'm abolutly lost as in the why of it. I previously posted this on comp.unix.bsd.freebsd.misc but i was advised to send here I was unable to find help on google :( To resume quick, when i'm in a jail, netstat doesn't work properly. Hopefully i have provided sufficient information for anyone willing to help me :p First of all, my system :

Hello, I have the following proplem. My DiffServ configuration is working fine when I do ping, but when I use mgen the packets are not detected at the core router. Here is my core router configuration: #!/bin/bash tc qdisc add dev eth1 handle 1:0 root dsmark indices 64 set_tc_index tc filter add dev eth1 parent 1:0 protocol ip prio 1 tcindex mask 0xfc shift 2 tc qdisc add dev eth1 parent

Newbie here... tcng version 10b I''m just learning about htb and using tcng. I am trying to make the example in Martin A. Brown''s Traffic Control with tcng and HTB HOWTO v0.5 example 2 /* * Simply commented example of a tcng traffic control file. * * Martin A. Brown <mabrown@securepipe.com> * * Example: Using class selection path. * * (If you are reading the

Hi stef and all I want measure the policy perfomance for video traffic on mpls diffserv network. there are two different polices for video packet 1. Video packets that are marked that are over the limit are to be rejected at the edge router. 2. Video packets that are marked that are over the limit are to be downgraded as best effort and are sent through. Before video enter my mpls

Greetings all, OK - just started playing around with traffic shaping - have imq and htb and (I think) everything else I need in the kernel and running well. My initial lab task was to protect a H.323 session over a simulated half T1 while adding bulk traffic - got that accomplished after slogging through learning tc and decided in short order that a more intuitive interface would be

hai all i need to implement CBWFQ in linux As i wrote script in edge as: which mark the EF traffic ____________________________________________________________________-__ #!/bin/sh DEV=eth0 tc qdisc add dev $DEV handle 1: root dsmark indices 8 tc class change dev $DEV classid 1:1 dsmark mask 0x3 value 0xb8 # making two filters tc filter add dev $DEV parent 1:0 prio 4 protocol ip u32 tc

hi all, i''m having problems building a module from my tcng configuration file. could someone verify the syntax for building a kernel module? i did it as shown below ... module gets built but i cannot load it. thanks charles ps -- sorry, don''t know c++ :-) [root]# cat /etc/tcng.test #define LAN "eth0" #define LAN_INGRESS 750000 #define LAN_EGRESS 750000 dev

Hi everybody, I want to do the following setup : | | Tun1 - Link 1 | Tun1 | | Router A | teql | INTERNET Link - | | teql |router B | | Tun2 - Link 2 | Tun2 | | This should permit to agregate Link 1 and Link 2 (less the cost of the encapsulation). The two tunnels are GRE ip tunnel. It seems to work fine