similar to: Anyone using PCI/USB xDSL under Linux?

I''ve been doing some research and I haven''t found the complete answer, so I thought I''d post it to all of you. Here''s what I want to do: RH 7.3 System with 4 NIC''s eth0 for PPPOE based DSL (netdsl) eth1 for DHCP based Cable Internet (netcable) eth2 for WWW, MAIL, FTP Servers (dmz probably DNAT) eth3 for 10.0.1.0 network (loc) I have Dynamic DNS for my

Hello all, I need a very simple routing protocol for VPN redundancy. We have several sites and each site has a Linux router and two IPCops each with an ADSL connection to the internet using different ISP''s. I have configured VPN''s between all of the sites for each IPcop on ispA and the same for the IPCops on ispB. This way, if one of the ISP fails, I change the route on the

I have absolutely no idea how to use linux and I am trying to install WINE. I am running Linspire 4.5 and I actually want to install winesetuptk (this is what it tells me to do when i try to run a program with WINE). I downloaded the tar.bz2 file from sourceforge and have no idea what to do from there. When you guys say, type ~/blah blah I do not know what that means, type it where? I need

Sorry, if this question has been answered before, but I could not find out with a brief look. How can I set the MAC address for a bridge? The MAC address given for the bridge device seems to be the one it sends network packets with if the bridge device has an IP address set. Apparently the bridge starts with a zero MAC address and when the first interface is attached to it, it takes its MAC

Hi I used to have a xDSL with a Cisco 677 router setup that connected via PPPoE to my ISP. I now have a different ISP that uses a xDSL modem setup which means my shorewall firewall machine external interface hooks up til my ISP by directly by DHCP and gets a real internet IP while before with my router setup . My question is: With my Cisco router setup i could from my LAN access my outside IP

Is it somehow possible to configure a bridge in 'hub' mode. So that every packet sent from a 'port' (eg. an interface) is delivered to every other 'port' on the bridge. That is, effectively to just turn off MAC address learning and treat all packets on the bridge level effectively as broadcasts. Or could this be done with some ebtables hack? Suggestions appreciated, --

I've been using my voicepulse connect number for over a month now, but today it simply won't connect. My partner and I each have a number, both are mapped in my iax.conf and extensions.conf files. This has been working fine. Today, either number gives this message: Feb 16 21:53:14 NOTICE[4330]: chan_iax2.c:5757 socket_read: Rejected connect attempt from 66.234.228.170, request

Hello Walter, On Sat, 13 May 2017 13:08:17 +0200 "Walter H." <Walter.H at mathemainzel.info> wrote: > On 13.05.2017 00:29, Robert Moskowitz wrote: > > I have been working, for the past few years, with armv7 SOCs and have > a number of servers working. > > > > Intel, etal are catching up with ARM and I have seen ones like: > > > >

Hi all, I am new to samba. I have created samba as PDC. I want to restrict users for changing settings. I have configured all client machines with XP. How can i use Group Policy with netlogon. Thanks in advance. Regards, Saravanan __________________________________ Do you Yahoo!? Read only the mail you want - Yahoo! Mail SpamGuard. http://promotions.yahoo.com/new_mail

Hello, I am just starting to research Asterisk and I would like to install it on a PC to try out. I have looked around quite a bit but I haven't found much information on the Linux part. I know you need to put Linux on the PC first but what version or flavor of Linux do you recommend? I contacted Red Hat and they had not heard of Asterisk and they said Asterisk is not certified for Red Hat.

>Message: 23 >Date: Fri, 13 Jul 2007 22:11:59 -0400 >From: Dan Halbert <halbert at everyzing.com> >Subject: Re: [CentOS] Newbie ADSL configuration, ppp0 can't activate & > config not found >Message-ID: <469830EF.3080601 at everyzing.com> >mailing-lists at computer2.com wrote: > I am frustrated. This is a dual boot box, Win XP (Spanish) and

I have one of my asterisks off an xDSL modem with a dynamic IP address. The IP address keeps on changing so I am curious as to what other people are doing to work around this issue. I am contemplating to register for a dynamic DNS service but then my communications become dependent on the availability of this service. The "host=dynamic" for SIP seems interesting. Any suggestions?

Hi, I use CentOS as a firewall/proxy/webserver/fileserver in my small network. As the small-spec machine with CentOS is heavily loaded/used I can't afford downtime. 20 GB, pentium II with only 128 MB RAM. However I want to know the news on 4.5 is it due soon? Can I gain more by running CentOS 3.x range on such an old machine like mine? Will CentOS 5.0 mean you need a minimum of 512 RAM?

fc2, samba 3.0.9 The samba server is PDC. Temporarily, the server was dhcp, which gave it the IP 192.168.1.64 we then set it to static 192.168.1.150, which is what we want. however, the different windows clients, on and off, on ping and such, resolve INTRANET, the netbios name of the pdc, to 192.168.1.64 still, despite me removing wins.dat. I even tried the following suggestion, to no avail

On Monday 29 November 2004 19:39, Chris Lattner wrote: > > > Alternatively, if you don't want to do that, you can build mem2reg into > > > your pass if it works better. To do this, your pass needs to > > > 'addRequired' DominatorTree and DominatorFrontier, then use the > > > interfaces exposed through > > >

Hello! My name is Denis Shaposhnikov. I'm looking for a job in EU (Germany is preferably) as a UNIX/FreeBSD system administrator and/or network administrator that lets me utilize my experience in an Internet Service Providing (ISP). Skills: * Operating systems: UNIX (FreeBSD 2.2 - STABLE), Cisco IOS (10.x - 12.x), ZyNOS. Understand how systems work and is able to apply this

I might be stupid and ask an idiot or offensive question, but here it is: "Why was tzdata-2007h [RHEA-2007:0928-05] only released for CentOS 2, when upstream has released it for all the versions?" The guys from X/OS have released it for 5.0 along with the other updates (on Oct. 9). Are the "enhancements"... "not important" as long as they're not "security

... is on SourceForge: http://tcng.sourceforge.net/dist/tcng-9m.tar.gz md5sum 636d382f6db917b385e7a6f158136ca2 See also http://tcng.sourceforge.net/ This release contains the upgrade to 2.4.26, plus a few compatibility changes. There''s also a major bug that strangely went undetected until recently, when Laurent Moutel reported that his classifiers behaved unexpectedly: if testing

Hi Timo, I've got a crash with dovecot 2.2 dovecot --version 2.2.rc2 (69c26a9e3be5) It's occured when accessing with imap on a large mailbox (around 50k messages) imap(clean-quarantine at spamguard.fr): Panic: Buffer full (4254 > 4248, pool <none>) Error: Raw backtrace: /usr/lib/dovecot/libdovecot.so.0(+0x6089a) [0x7f9d1bcde89a] -> /usr/lib/dovecot/libdovecot.so.0(+0x608de)

Hi All, I'm trying to get my Mother's ADSL USB Router to work on CentOS 4-3. I see the device in Hardware Browser/System devices but nowhere in Network Configuration is it an option. I even tried New/xDSL but it doesn't appear as an option there either. Any suggestions for this? Cheers. Mark Sargent.