similar to: htb: class isn''t work conserving ?!

I just realized that I hadn''t actually asked a question when I posted this before. Let me try again... I am trying to configure a Linux box with all possible VLANs (4094 of them), and a subnet on each VLAN. Creating the VLANs isn''t a problem. But, when I try to use "ip addr add ..." commands to assign an IP address to each VLAN interface, I get to do about 280 of

Hello, for the umpteen time Patrick Turley <pturley@rocksteady.com> sent: > <eom> Too bad this wasn''t on the, then I could set by watch to it. Steve _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

I''m getting the following error/warning at some point in my config script, and I''m not sure which class it is referring to. htb: class 10007 isn''t work conserving ?! I [think I] understand that htb is a non-work-conserving qdisc, and I [think I] have configured things so that every htb qdisc I instantiate limits the bandwidth, so I don''t understand why this

Our system has potentially a few thousand firewall rules and HTB classes. I need to find out the amount of memory these things consume: - iptables firewall rules - HTB classes If anyone has any easy links to this information, that would be great. Failing that, a pointer to a good place to look in the source code would be very helpful. _______________________________________________

>>eth1 & eth2 are both connected to the EN5861 router. I''ve done that >>because I couldn''t work out any other way to use the static IP address >>that out ISP have given us. >> > >Aha, this is a config question. You can just add as many ip addresses to each physical card as you like. I forget the exact syntax, but check man pages for

>>Our ISP has given us 5 static IP address plus one router IP address >>and I was wondering if I could get rid of their stupid EN5861 router >>and set up the linux machine to handle all the static addresses and >>routing. I figured I''d have to set up alises for other IP addresses >>eg ifconfig eth0:0 >>xx.xx.xx.193 but once I''ve done that

>> No I am using the EN5861, just that we have two ADSL lines and only >> one >> EN5861 and rather than buying another I''d like to use linux to do the >> same job as the en5861, if you know what I mean. > >You can, but since you have two ADSL lines, you''ll need two ADSL devices of some kind, whether it''s a pair of 5861s, or a 5861 and an

Hey all. I''m trying to set up QoS using the HTB qdisc in a very basic setup, but it the example shown in the howto doesn''t seem to be working. While the packets show up in the correct classes, they appear to be completely ignoring the rates, meaning nothing gets shaped. My setup is that I''ve got a a bunch of machines behind my firewall/router: 1.2.3.1

Hi, can any body suggest any tool which can show the utilisation for individual classes for HTB. preferable written in C/or shell script. Regards Jayesh ------------------------------------------------- Still single? Click here to find the perfect match. http://www.bharatmatrimony.com/cgi-bin/bmclicks1.cgi?141

I posted earlier when I noticed that htb was releasing packets in pairs, even though my burst/quantums were 1 pkt. To fix I set HTB_HYSTERESIS 0 in net/sched/sch_htb.c . This gives a noticable gain in upstream worst case latency, for me with 256kbit/s up I used to see +90 sometimes, now it''s +45. For the many who have 128 up it should limit them to +90 rather than +180. Andy.

Hi, we r using HTB algorithm,for traffic shaping, we are facing a problem. we are able to create multiple classes,filters. But when we delete 1 filter all filter gets deleted. how do we avoid that. waiting for you reply Regards Jayesh ------------------------------------------------- Shop & Save at Sifymall.com! Special Festive Offers - up to 60% off on DVD players, MP3 Players. Mobile

If I create a cbq qdisc as a leaf of a cbq class, the bandwith rate is the same of the root cbq qdisc or the rate of the cbq class? Does exist the parameter rate on the "tc qdisc add" for cbq command? tc qdisc add dev eth0 root handle 1:0 cbq bandwidth 10mbit avpkt 1000 cell 8 tc class add dev eth0 parent 1:0 classid 1:3 cbq bandwidth 10mbit rate 50kbit allot 1514 cell 8

Hello, Does anyone know when one should use cbq versus (simpler more accurate) htb? Specifically does cbq have added functionality that may be of interest to certain applications? from htb home> Both CBQ and HTB help you to control the use of the outbound bandwidth on a given link. Both allow you to use one physical link to simulate several slower links and to send different kinds of

Hi guys, I''m new to TC HTB traffic shaping.... I installed it at my first try on my Bearing Leaf Router/Firewall I use the tc -s class show dev eth? To see my output All looks dandy and nice, but it''s figures, of which at current momment looks like French to me, I would like to see exactly what these figures looks like in a GRAPH style... I know I can use MRTG, I do have

Hi, One more of those ... 1) what is a ctoken with regard to HTB? Does the ''c'' stand for ceil and if so how is it different from tokens? 2) Is the difference, only in the generation of these tokens? 3) Would the ctokens and token be treated equally once borrowed? Kindly help. Thank you. Regards, suraj. __________________________________ Do you Yahoo!? Protect your

Hi, All, Does anyone have working scripts using HTB for QoS but IPtables for filtering? I want to learn how to put them together. Do the scripts working on Redhat? Thanks in advance, James

I downloaded iproute2-2.4.7-now-ss010824.tar.gz and I did patched tc with the htb3.6_tc.diff from htb3.6-020525.tgz and when I try to use a htb script I get just errors. I did not patch the kernel, since I use kernel 2.4.21 and I saw on - HTB Homepage that I need to patch it only if I run version 2.4.20 or earlier. Do also need the kernel patch ? Or maybe is something else wrong? RTNETLINK

HTB and imq was used to control traffic. AC="tc class add dev eth0 parent" $AC 1: classid 1:1 htb rate 100kbps burst 2k $AC 1:2 classid 1:10 htb rate 50kbps ceil 100kbps burst 2k prio 1 $AC 1:2 classid 1:11 htb rate 50kbps ceil 100kbps burst 2k prio 1 please tell me the range of "prio" _________________________________________________________ Do You Yahoo!? 新鲜到底,娱乐到家 -

Hi everybody! I''ve been trying with htb and tc filter. It seemed to work fine, but after testing with ethloop I''ve realized that traffic is not being distributed through the leaves as I thought. When sending packets to 1:10 and 1:11 at the same time, there''s no bandwidth sharing. There''s no traffic through 1:11 until traffic through 1:10 has finished. Though

Dear All, Sorry to trouble again..... After go through www.lartc.org I have implemented the HTB instead of CBQ for the same scenario. Now following files are under /etc/sysconfig/htb directory. eth0 DEFAULT=30 R2Q=10 eth0-2.root RATE=256kbps BURST=25k eth0-2:10.comp1 RATE=120kbps BURST=12k PRIO=0 LEAF=sfq RULE=192.168.200.0/24 eth0-2:20.comp2