similar to: qdisc associated free software

I just installed Xandros 2.0 Desktop. I used apt-get to install iproute. I then downloaded wondershaper 1.1a from the website. I edited the script as the readme says. I went to console and started the wondershaper script...and i get the following error messages. RTNETLINK answers: Invalid Argument many times. Any ideas what is wrong? MArk _______________________________________________

Greetings, I''m new to LARTC and I''m trying to solve a problem with multiple clients accessing a game server. So I thought I''d give traffic control a shot. I''ve downloaded Wonder Shaper and have added this to the default script: tc filter add dev $DEV parent 1:0 protocol ip prio 12 u32 \ match ip protocol 0x6 0xff flowid 1:3 I''m now quite sure

we have an external 2Mbit dsl connection and running on it are several gre vpn tunnels so far i''ve given priority to the vpn traffic (using htb) can i now put rules in for the tunnels to control traffic within each tunnel (that''s where our video conferencing etc runs)? or can i only control the real interface (eth1 in our setup)? if not can i somehow see the packets inside the

Hi, I just installed wondershapper 1.1a on my ipcop firewall box. I have roadrunner cable with a ftp server setup. My download speed is 2mbit (I get 225 KBytes) and my upload is 384kbit (I send at 43 KBytes). What should the settings in wshaper? I can ping yahoo.com at 90msec with little traffic.....and at around 220msec with full upload traffic. Mark

Hi, i have one firewall/gateway server with two interfaces and a routing problem (?). eth0: external interface eth1: internal interface. Both ip address are valid. Services like DNS, HTTP is configured to run using eth1 ip address. The problem is when i try to connect from internet to firewall, i can´t see eth1 ip address... only eth0 ip address. So, when i try to connect to web

I''m rate limiting and prioritizing traffic upstream of a slow wan link using htb, classic wonder shaper type stuff. I''m using the following command for traffic that does not match any of my defined filters: tc qdisc add dev eth0 root handle 1: htb default 50 It appears that local, non-routable traffic like arps and igmp are being snared by this and end-up queued in the lowest

Hi all Does anyone know if i can use ethernet aliases like eth0:1 in advanced routing like multipath routing in order to avoid to have nxEthernet interfaces in my Linux box. Thansk in advanced -- Guillermo Gomez <ggomez@neotechgw.net> neotech _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:

Hello again, I may have a common problem to solve but it seems it is harder than I thought... I have 2 internet providers (each one having a different gateway). Behind the router there are around 100 clients that are SNAT-ed. I want some clients to be SNAT-ed to the first provider, while the others to the second one. The following lines should work: iptables -t nat -A POSTROUTING -s

Hi, I''ve modified my copy of the wondershaper script to add a few filters that allow traffic to and from a few specific ips go through with a speed of up to 100Mbits... I increased the root from 10 to 100mbit, and added this bit of code a bit further down the script; # Real time hosts for i in 62.101.244.63/32 216.74.158.11/32 216.74.158.3/32 216.74.158.57/32; do tc filter add dev

Hullo :) I appear to be having a common problem, but the standard fix hasn''t worked for me :/ I''m using a 2.4.23 kernel, with QoS options thusly: # QoS and/or fair queueing # CONFIG_NET_SCHED=y # CONFIG_NET_SCH_CBQ is not set CONFIG_NET_SCH_HTB=m # CONFIG_NET_SCH_CSZ is not set CONFIG_NET_SCH_PRIO=m CONFIG_NET_SCH_RED=m CONFIG_NET_SCH_SFQ=m CONFIG_NET_SCH_TEQL=m

Hi, I am new to this group. I use this script tc qdisc add dev eth0 root handle 1: htb tc class add dev eth0 parent 1:0 classid 1:1 htb rate 500kbit ceil 500kbit tc class add dev eth0 parent 1:1 classid 1:2 htb rate 300Kbit ceil 500kbit tc class add dev eth0 parent 1:1 classid 1:3 htb rate 200kbit ceil 500kbit I like to know: If two customers of the same class (for example 1:2) work

Hello all, Im new using tc, ive been reading the howto at least 2 or 3 times, but there''s a lot information to aquire all of it quickly. I''ve installed a linux box as firewall for a wireless Network in a hotel, this box is a radius for the access points and it uses iptables to redirect and permit/deny the customers to use the net. So it uses iptables to count the bytes to

Hi all, Given below ia the simple network diagram. I need to control uplink for the individual private network IPs as depicted in the diagram. Is this possible in a NATed environment using CBQ or HTB. I learnt that we can control only outgoing traffic. So if I control in the eth1 interface the source IP will be masqueraded, and it may not result in the desired behaviour. Is there a solution to

Hi all! I just started to experiment with bandwidth management using tbf. I have the folowing problems with token understanding: 1) What unit is token? Is "1 token = 1 byte" ? If this is so, then with rate=0.5mbit and HZ=100 the bucket gets filled with 0,64kb (655 tokens) every 10ms? 2) How much tokens are used for one packet (1500)? 3) And token unrelated question. Does

Hi, I wanna do some shaping on a DSL line that is plugged to the eth1 nic. Should I attach the qdiscs directly to the ppp device or can I use the eth1 device instead? What (and why) makes more sense? thx cb _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Hi; I have two dsl lines, which the low bandwidth connection(ISP2) is only used for failover. My setup is showed below; \ ISP1 \ / \ ____/NAT My internal net |-----|___| / \NAT / \ / ISP2 However, my interfaces which these lines are connected are both

Hi, how can I filter IPsec traffic with u32 filters? I know IPsec needs Port 500/UDP and IP protocols 50 and 51. I know how to get the port stuff, but how can I make u32 to match the protocol number? thx, cb _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Hi all, Is there a way to create a class that limits the amount of packets of any rule in a period ( like pps ) ? Some aplications like game servers, send so much little udp packets to the clients that the router cpu gets exausted, even with relative low bandwidith usage. Any idea ? Luciano _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl

Two easy questions after having read the LARTC HOWTO document (which by the way is a *fantastic* document. Congratulations to all who contributed!) First is: Can I prioritise my "drops" on incoming traffic when the link is overloaded. ie instead of just tail dropping, can I "prefer" to drop certain classes of traffic? If so, do I do this by setting up, say, a HTB tree

Hello, I connected the network 192.168.1.0 with 192.168.2.0 over the internet trough a GRE-Tunnel. I don''t know if I set up all things right: The client-pcs in both networks have a subnet mask of 255.255.255.0 and 192.168.2.x''s default gateway is the server wich has started the tunnel. The 192.168.1.x''s default gateway is 192.168.1.250 wich routes traffic destinated to