similar to: wondershaper question

I''ve gotten wondershaper to work in my linux box, which is part of a 3 computer network that shares the same dsl connection. The linuxbox handles most bulk down and uploading, and the other 2 are mainly for surfing and such. What I need from wiondershaper is that it should perform it''s tasks with all of the traffic to the dsl modem, but do nothing with the internal traffic

Hi, I just installed wondershapper 1.1a on my ipcop firewall box. I have roadrunner cable with a ftp server setup. My download speed is 2mbit (I get 225 KBytes) and my upload is 384kbit (I send at 43 KBytes). What should the settings in wshaper? I can ping yahoo.com at 90msec with little traffic.....and at around 220msec with full upload traffic. Mark

Hi Is there a way of marking packets by mac address instead of ip or ports using a "tc filter u32 match"? I read somewhere that I could use the offset -8 and -14 to grab the mac addresses but if I use anything lower than -8, for example -9, I get an error. I''m modifying the wondershaper script to cap the download speed by mac address. Any sugestions?

Hi all, ive got wondershaper working well with the highest download while maintaing minimal latency but the problem is this: ive got 2 nics in the linux router eth0 and eth1. eth1= internet interface but this is connected to a router say 10.0.0.190, now off that router there are other servers, mail server, domino server etc now if i shape on eth1 ingress and egress using the wondershaper script

Is there a way to apply wondershaper w/ htb to a port range? I have a ftp server on port 65432 and passive ports 50000-60000. Is there a way to set a range? or do they have to be individually listed? The following doesnt seem to work: # low priority source ports NOPRIOPORTSRC=65432, 50000:60000 # low priority destination ports NOPRIOPORTDST= Mark

Hello Thilo, What did you find superior with CBQ-wondershaper over HTB-wondershaper? We have not been using wondershaper specifically but our simple tests so far seem to show that htb is much easier to configure for a given target shape (i.,e accurate) compared to CBQ. Torsten -----Original Message----- From: Thilo Schulz [mailto:arny@ats.s.bawue.de] Sent: Saturday, June 14, 2003 8:55 AM To:

I have two interfaces, eth0 and eth1 but i can''t discern the egress traffic than ingress traffic. I need to apply htb qdisc in both directions, and I read that I need the IMQ patch to do this, because in ingress qdisc i can''t apply htb qdisc...but where is the ingress qdisc? affect the traffic that goes from eth0 to eth1 or is for the traffic that goes from eth1 to eth0?

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello, been awhile since I''ve written. I now have a situation where I get to use traffic shaping for a client. ~ We implemented the WonderShaper script on our own firewall and experienced no problems. I made some modifications to it to add IPSec protocol packets into the 1:10 high priority class using the u32 filter. ~ So far on our

I''m having a network inside of a dsl modem and I''m using wondershaper on the computers to be able to surf while bulk downloading. The problem is that also the internal traffic is shaped, which means the internal network is at 200kb/s, instead of 100Mb/s. Is there a way to exclude the internal adresses from the wondershaper rules, or is there any other good way to solve this?

Hi ! I´ve been using the wonderful wondershaper from chapter 15.8 of the LARTC Howto for some time. It´s really wonderful. Actually, I use the version from http://freshmeat.net/projects/wshaper/?topic_id=87 Now I tried to put some hosts to low priority, and it doesn´t work. The traffic is splitted equally between the noprio and the other hosts. Is this because I use ip masquerading, and all

Hi all, I need to provide shell hosting for about 40 users, and few days ago I found the wondershaper script, so Im trying to know if this script could help me to improve interactive ssh/telnet connections. Wondershaper could help me or its only efective on OUTGOINGS requests? Ok, any comment and feedback will be welcome. Sorry for my bad english and THANKS in advance.

Hi, I really like the wondershaper script, it works very well for me. My question is this. Is there a way to get certain remote hosts to be excluded from the shaping? I ask because I don''t have my box connected directly through the net. It sits behind a nat device, and has ports forwarded in for services. I''d like to limit the ports and services, but only to things going outside

Hello everyone. I''ve been trying to get Qos to work here for two days now, but it REALLY doesn''t seem to work the way I want to. Here is my situation: Internet Wireless LAN Firewall DMZ Local lan As you can see, I got a Debian box in the middle as my firewall with 3 network interfaces and a wireless one. I use

hello, a friend of mine have this configuration: 10 x PC -- router/linux/rh8 -- ADSL Modem -- ISP let''s say that the bandwidth is: 5M and 800K he does dc++ and counter-strike, so let''s say the UP is full, and the ping from the counter server is 300ms, the server cut the connection, and no more game, the player is unhappy. The normal ping is 50ms. so he thinks to put some

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all! when I activate wondershaper on my dsl connection (pppoa vc mux), i get three errors: # sh -x /usr/sbin/wshaper ppp0 + /usr/sbin/xmlstarter setenv tc_downlink + DOWNLINK= + /usr/sbin/xmlstarter setenv tc_uplink + UPLINK= + [ -z ] + cat /proc/avalanche/avsar_modem_stats + grep Connection Rate + awk {printf("%d", $8)} +

Dear All! I reach the point that I must ask you what I have to do. I am beginner at traffic shaping and I''m very confused with it. :) Here''s my script that doesn''t do what I want to do with it: tc qdisc del dev eth1 root tc qdisc add dev eth1 root handle 1 htb default 2 r2q 10 tc class add dev eth1 parent 1: classid 1:1 htb rate 300kbit tc class add dev eth1 parent 1:

I have wondershaper to limit my upload at 400kilobits (my line is 600kbps). I do a lot of torrent seeding and I dont want my pings killed when I''m uploading so I set low prority source ports as follows (by the way, I have bittornet to only use ports 6881-6910): NOPRIOPORTSRC="6881 6882 6883 6884 6885 6886 6887 6888 6889 6890 6891 6892 6893 6894 6895 6896 6897 6898 6899 6900 6901

Hi, I have tried unsuccesfully to limit my ftp server send speed in linux. I have an ipcop linux firewall/router with 2 nics. 1 nic (eth1) is connected to a 3mbit/384Kbit cable connection and the other (eth0) a switch. Behind it i have a suse linux box and a windows box. On the suse box i run proftpd. I need to shape my passive ftp send speed to 34KBytes because if it is maxed out at 45K

Hi, I am new to the Linux Advance Routing Project and to Policy Based Routing as implemented in Linux.... but I have been using Linux for 10 years so not _really_ a newbie.... Looking at the lartc.org website I came across the reference implementation of a traffic shaper... I also have Matt Marsh''s book on ''Policy Based Routing using Linux'' which covers traffic

Hi Couple months ago I started to have a strange problem with HTB. My setup is Fedora Core 2 + Pentium 2 233 + 128 MB of ram and its serving as a router. For some time since going to kernel 2.6 my HTB QoS Stalls for couple seconds, every couple minutes. If the connection load is bigger the stalling is more frequent and takes longer. I isolated the problem to be with HTB (CBQ works fine). The