similar to: WRR problem and other things

https://www.p2pwatchdog.com/ > -----Original Message----- > From: lartc-admin@mailman.ds9a.nl > [mailto:lartc-admin@mailman.ds9a.nl] On Behalf Of Roy > Sent: Thursday, September 02, 2004 5:04 AM > To: Ing. Marcos Salvatierra; James Lista > Cc: lartc@mailman.ds9a.nl > Subject: Re: [LARTC] adsl and p2p programs > > This is most asked question but there is no good

Hello, I''m trying to get my shaper to work, but have only a partial success. Can someone help me with that. My setup unfortunately is not so trivial, but I think some people could have similar one... 1. There is a router connected to the internet line via interface eth0 2. There are users connected to the router via two interfaces : eth1 and wlan0 3. All users are assigned private IP

i''m trying to limit upload and download but something is wrong(it is about NAT) i will post here my "script" maybe someone could tell me what is wrong my kernel(2.6.9) is patch with imq(linuximq.net) and my iptables(1.2.11) also #flush tc qdisc del dev eth0 root tc qdisc del dev eth1 root tc qdisc del dev imq0 root tc qdisc del dev imq1 root ifconfig imq0 down

hola listeros! existe algun script webScript, proyecto, herramienta o lo que sea, que sirva para medir el trafico total de una lan, como para hacer reportes mensuales por host ? necesito hacer algo asi: host Trafico/mes ----------------------------- 192.168.1.x1 xxxxx Bytes 192.168.1.x2 xxxxx Bytes 192.168.1.x3 xxxxx Bytes 192.168.1.x4 xxxxx Bytes ese seria un reporte a efectuar el ultimo

Hi folks, I`ve a problem to use HTB and SFQ. The first script, below, to show a simple configuration, does work fine...!!! But, in the second example, does not work, becouse i put more code to clasify the traffic by protocol, http and ftp in this case. Somebody can tell me the errors? Thx, in advance.- NOTICE: IMQ device is to asociate with ETH1 my external iface. SCRIPT que funciona:

Hi, i am running imq + htb on my router , the situation is like this eth0 = uplink to my provider eth1 = 1st customer eth2 = 2nd customer eth3 = 3th customer eth0 has limit 512 and i want to share this between eth1 eth2 and eth3 , but not working , this is the script i used, \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ #!/bin/sh

On 2/19/07, Salatiel Filho <salatiel.filho@gmail.com> wrote: > Well , thanks to imq all my client machines are now shaped and > everything is great ... > But now i have a doubt , is there a way to shape the traffic that goes > to the route [doing a wget from the router for example ]? > > > I have a PREROUTING IMQ0 and a POSTROUTING IMQ1 , everything is > working like

Hello to all people there . Can i guarantee ICMP respond time no metter how loaded is internet line . i have typical NATed enviroiment like External IP |linux router| LAN - 192.168.0.0/24 i have example setup with IMQ but is it possible to be done also if i attache htb to eth0 and eth1 for example . if i start shaper ping i better that without shaper but it''s not guarantted i mean

Hi. The configuration script is at the bottom. My configuration looks similar to this: imq0 | 1:1 (12mbit) | 1:2 (10mbit) | 3:0 | 3:1 (256kbit) / \ 3:2 3:3 icmp (rest) both 3:2 and 3:3 have rate 1kbit ceil 256kbit Icmp bucklet have priority 1 (better), "rest" bucklet have prio 2 (worse) I tested the script with heavy download

Folks, I''m so surprised what happened to my box just in the few weeks lately. Here is my setup: INTERNET <----------> [eth0] SHAPER-BOX [eth1] <----------> USER-FARM both eth0 & eth1 got public ips (202.x.x.x) Why traffic monitored at eth0 is bigger than eth1 ? eth1 shaped just exactly the same as rate i defined in HTB. I just have 1024Kbps from my ISP and i defined the

Hi All, I''ve just installed WRR and am looking at tools to monitor, graph and display the system and throughput of each queue/class/filter. I''ve looked at: iptraf - only shows tcp/udp flows, not QOS queue throughputs show.pl - doesnt work with WRR (as far as I can tell) tc-graph.pl - doesnt work with WRR (as far as I can tell) polltc_ - doesnt work with WRR (as far as I can

Guys Given the replies and interests lately on the WRR scheduler, and the shameless promotion of Route Hat (only kidding), my question is simple. Is there an alternative for the 2.6.x kernels? >From what I gather WRR is only available for the 2.4 kernels... Regards -- Kenneth Kalmer kenneth.kalmer@gmail.com http://opensourcery.blogspot.com

I have set up wrr successfully on my bridge/shaper machine. That much works fine. I originally used sfq in the inner classes. However, there was a problem with high-bandwidth connections (web downloads, bittorrent) starving low-bandwidth low-latency connections like ssh. I would like to use prio or similar to prioritize the interactive traffic, but it does not seem to work. I have tested with

For some time now im trying to get to know what causes such configuration of QOS (kernel 2.4.25-2.4.28 + IMQ patch and ofcourse wrr): -- WRR_MAX_CLASSES=200 DEV_IN=imq0 ifconfig $DEV_IN down ifconfig $DEV_IN up tc qdisc add dev ${DEV_IN} handle 1:0 root htb default 10 tc class add dev ${DEV_IN} parent 1:0 classid 1:10 htb rate 1000kbit burst 1kbit prio 1 tc qdisc add dev ${DEV_IN} parent 1:10

Hi all, Here''s the situation. I have 80 users sharing a internet link of 5Mb link. The users are grouped in /29 ip addr classes so I have 10 classes of users I want to create a root htb, then 10 htb childs each with 0.5Mb bandwidth. The traffic will be directed to each class using tc filters. Now, I want that each of 8 users from each class to share equally the class bandwidth. Can I

How can i redirect all traffic that not come from port 80 to a flow ? i was thing about some like tc filter add dev imq1 parent 1: protocol ip prio 7 u32 match ip sport !80 ...... But this not work. Another doubt, if i have two rules that intersects , for example , one filter with u32 match ip src 10.10.10.10 flowid 1:10 and other with u32 match sport 80 0xffff flowid 1:11 , which one will

Could anyone explain what is WRR param2 [wmode2 , incr2 , decr2 , min2] for ? can i set just the param1 ? [wmode1 , incr1 , decr1,min1] -- []''s Salatiel "O maior prazer do inteligente é bancar o idiota diante de um idiota que banca o inteligente".

Guys Oppologies for the cross post. I''ve been scouring the docs coming with the wrr patches and for the life of me I can''t figure out why there are 8 parameters for each class. <snip> weight1, min1, decr1, incr1, weight2, min2, decr2, incr2 </snip> According to the docs these parameters are handled the same way, but looking at the example scripts there are

Attaching WRR to a hfsc ot htb class after a while i will get all packets drop and syslog full of HFSC or HTB : Non-work-conserving qdisc any ideas ? -- []''s Salatiel "O maior prazer do inteligente é bancar o idiota diante de um idiota que banca o inteligente".

is possible to setup any bandwith resource control in a ppp0 interface? i''d like to distribute bandwith equally between pcs in a network, and inside each pc, equally between protocols... is this possible? all the documentation refers to eth0 type interfaces... so? -- $~ who | grep -i brunette | date ; cd ~ ; unzip ; touch; strip; finger; mount; gasp; yes; uptime ; umount; sleep Diego