similar to: how to bring down htb rate to 3kbit?

Hello Stef, I am working on a Bandwidth management project as part of my college curriculum.I am running TCNG 10-b but I am not able to classify packets based on MAC address using tcng, so I am running tc commands in /tcng/bin and they are working. But is there a way out to classify packets based on MAC address using TCNG. And, I am successful in throttling down the Bandwidth to 8kbit

Hello Everybody, I have configured a Linux box that does traffic shaping. Its working wonderfully fine, just as expected...Now i want to measure the bandwidth consumed by each of my hosts....But I dont want SNMP to run on all the hosts[as required by MRTG] I used iptraf on my linux box, but it only measures the bandwidth on interface basis only.... I tried installing traffic-vis, its not working

Hello All, I am trying to prioratize VOIP traffic from data. The follwing link says that HFSC is better than HTB for shaping VOIP traffic. http://www.voip-info.org/wiki-QoS+Linux+with+HFSC I am in search of good documentation to start with HFSC, I am unable to understand the parameters used. I "googled" a lot to find on how to use HFSC, but no luck. Can anyone of you get me a link To

Hi... I''m working with HTB, and have a question... what happen if I create a class of "8kbit" ?? I get a log : "HTB: quantum of class .... is small. Consider r2q change" but, my r2q=1 I can''t reduce that variable... how must I procced ? Thank you! mac _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl

Hello All, I have a linux box running with three NIC''s, I have used brctl tool to configure this box as a bridge, i have given it ONE logical ipaddres, Every thing is working fine, but now i am required to configure the same bridge as a LOAD BALANCER.... On some googling i found the following link http://lartc.org/howto/lartc.rpdb.multiple-links.html This HOWTO requires me to have one

Hello All, I was curious to know if I can do traffic shaping on abonded Interface? Ex: I have to interfaces eth1 and eth2 which i have bonded together as bond0 , now the question is can I do shaping on eth1 and eth2 ?? Thanks KartheeK --------------------------------- Here''s a new way to find what you''re looking for - Yahoo! Answers Send FREE SMS to your

Hi everyone, My HTB script is showing me those "r2q change" warnings. I read that I should test with r2q values to gain accuracy and stop the warnings but I made some tests with r2q and with burst and I still get the warnings. Any ideas on this issue will be very helpful. The script seems to be working as the bandwidth for the IPs is being shaped. The NIC works at 100mbit and the

Hello all, I am providing broadband service through DVB circuit. I have 4KB uplink and 32KB downlink. I want to share 32KB downlink bandwidth among 192.168.0.0/24 (20 users in this subnet i.e 192.168.0.2-192.168.0.22)subnet where each user will get 2KB to 6KB bandwidth. And from 4KB uplink bandwidth each users will get only 1KB to 2KB bandwidth.

Hello, I wrote a simple traffic shaping script (below) that should have allowed me to shape my internet traffic a bit (ppp0 - adsl 128kbit/64kbit; local interface eth0). The script works only partially - the speed is being limited but too much. Without running this script my download rate is about 10kBytes (with second computer also downloading at about 6kBytes). After running it my download speed

Hi Stef, Sorry to write to you directly but my list membership is not working, I receive the archive but cant send to the list, cant delete myself because I don''t exist and can''t rejoin as they say I do exist, anyway hope you don''t mind Can you tell me what the difference between these two scripts is please. What I want to achieve is a high speed channel 1000kbit from

How can i redirect all traffic that not come from port 80 to a flow ? i was thing about some like tc filter add dev imq1 parent 1: protocol ip prio 7 u32 match ip sport !80 ...... But this not work. Another doubt, if i have two rules that intersects , for example , one filter with u32 match ip src 10.10.10.10 flowid 1:10 and other with u32 match sport 80 0xffff flowid 1:11 , which one will

Hi, I''m trying to setup QoS in my TSL box. Following to mailing list reccomendations I changed PSCHED_CPU but can''t get accurate shaping with HTB. I have disabled HYSTERESIS also (by setting it to 0). I have Intel Celeron 1.8Mhz (TSC supported I think). ******** My script ****** tc qdisc add dev eth0 root handle 1: htb default 22 r2q 10 # Class corresponding interface

Hello, I was trying to integrate AD to Cent OS 6 server. As part of it I was running into these error, listed below. Authentication is successful against the AD server using wbinfo, but cant able to list user information using wbinfo. Not sure what might be the issue. error message: [2012/01/17 15:12:49.472876, 1] winbindd/idmap_ad.c:651(idmap_ad_sids_to_unixids) Could not get unix ID

Hi, We have a 256 kbits/s (kilobits per second) link to the internet. it is a router running Linux that belongs to our ISP. They have given us 8 internet ips. (i.e- subnet is 255.255.255.248). one has been given to this router. I have given another internet ip to the firewall running CentOS 4.5. iptables is running on it. And also, I have installed iproute2 pkg as well. pls see below for

On 2/19/07, Salatiel Filho <salatiel.filho@gmail.com> wrote: > Well , thanks to imq all my client machines are now shaped and > everything is great ... > But now i have a doubt , is there a way to shape the traffic that goes > to the route [doing a wget from the router for example ]? > > > I have a PREROUTING IMQ0 and a POSTROUTING IMQ1 , everything is > working like

Dear All, I''m using the kernel 2.6.6, iproute2-2.4.7.20020116, iptables v1.2.9, and gentoo. I have a leased-line 64 kbps. I can see the counter works in iptables, but in the htb, it doesn''t go to the right class (it always go to the default class). Any help will be appreciated here''s my htb conf #!/bin/bash tc qdisc del dev eth1 root tc qdisc add dev eth1 root

Hi,lartc I used iproute-060110 with iptables1.3.4 on gentoo 2005r1 kernel 2.6.14-5. I find some error messages in system logfile: HTB: quantum of class 10001 is big. Consider r2q change. HTB: quantum of class 10010 is big. Consider r2q change. tcf_action_init_1: successfull police HTB: quantum of class 20001 is big. Consider r2q change. HTB: quantum of class 20020 is big. Consider

Hi, I have a Debian based NAT router. How can I manage upstream egress bandwidth based on the LAN ipadress in the network below? My goal is that host1 get a minumum of 10Mbit up/down and host2 gets a minimum of 90Mbit up/down, both max 100Mbit up/down? targethost 172.16.255.254 | | 172.16.0.1 natrouter

Hi all: I hope someone can help me with this "little" problem... I''m using a linux script to sub-divide my bandwidth (64kbit) into: 40kbit for VOIP, and the remaining 24kbit for http. So, the commands I''m using are: ============================================ #!/bin/bash # This script shapes "downloading" stuff # Initial qdisc tc qdisc add dev eth1

Dear all, I''m new to traffic shapping although i have gone through marking and HTB queueing but i felt trouble in tc filter . I wonder if any one give me the hints about quantum or r2q. i guess quantum is used when two class has same prio and rate and want to give first priority between them and control the borrowing traffic. It should be set more than MTU too. But my