similar to: Howto? 2 interfaces, same network, same gateway

I am having problem in ping or connect AP from Mobile Node(essid & channel is the same,maybe routing did not set properly but i fail to configure with route add default gw 192.168.3.4,its alway said network is unreachable ),My Mobile Node is using acx100 as driver while AP(redhat 9.0) is using HOSTAP 0.1.3.Any one can help? I heard How-To said we not need to set address on eth0 & wlan0

Hi all, On my Suse 9.3 prof. server I had two NIC’s: Eth0 IP 192.168.1.1 Eth1 IP 192.168.2.1 Now I added new NIC (eth2) Eth0 IP 192.168.1.1 Eth1 IP 192.168.2.1 Eth2 IP 192.168.1.2 Now I erased eth0 config and turned off this NIC in motherboard bios Eth1 IP 192.168.2.1 Eth2 IP 192.168.1.2 I renamed eth2 to eth0 Eth1 IP 192.168.2.1 Eth0 IP 192.168.1.2 And, finally I

Hello, I have the AR9285 wireless adaptor on an HP DV6-2128ca notebook. I can see it. it comes up in NetworkManager but never gets an IP. the router is a linksys using WPA/PSK security. Would/could someone please help me out trying to get this to work? Output of several commands follows: dmesg: ath: EEPROM regdomain: 0x69 ath: EEPROM indicates we should expect a direct regpair map ath:

Hi all, Long email but please be patient :) I am part of EHAS [1], a non profit organization which main goal is to improve the Healthcare assistance in isolated rural areas in developing countries. Recently we have developed a long distance Wi-Fi network in Cuzco (Peru). This network provides connectivity to 12 nodes (they are in fact Health Centers). As VoIP is a essential service in this

I have a system that does *not* have a graphical desktop installed, nor do I ever plan to. I have its wired ethernet working just peachy. Now I want to configure a USB wireless ethernet and scratching my head. Particularly since I don't use NetworkManager, everything is manually configured. That said, if I enable NM, I see this in /var/log/messages: NetworkManager[26900]: <info>

I have an Everex laptop (ick, but it was super cheap) that has an Atheros wireless NIC in it, but I can't seem to get it to connect to my wireless in-home LAN. Here's what I've done so far (that isn't working) - any suggestions? [root at marktop mark]# lspci | grep Ether 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 7c) 05:01.0 Ethernet controller:

Hello all, I'm trying to bridge the wlan0 and eth0 on an embedded system. I used the following commands to setup the bridge: ifconfig eth0 0.0.0.0 promiscuous ifconfig wlan0 0.0.0.0 promiscuous brctl addbr br0 brctl addif br0 eth0 brctl addif br0 wlan0 brctl sethello br0 1 brctl setmaxage br0 4 brctl setfd br0 4 ifconfig br0 up The eth0 is connected to a local network, and wlan0 is set to

Hopefully this is a simple answer. I am new to setting up bridges on a linux system. Here is what I have set up: Laptop directly connected to the eth0 port on the bridge (A Soekris 4521 board). The otherside of the bridge is a wirelass lan card (SMC2532b-w) as wlan0. The wlan0 is setup in managed mode to communicate to my test ap2000. When I do a 'brctl showmacs br0' on the

Hi, my box is connected to 3 networks, eth0 eth1 wlan0. I want "my" traffic to go via wlan0 and everything from eth1 NATed to eth0: eth0 192.168.1.10/24 eth1 172.16.1.1/12 wlan0 192.168.10.190/24 I first tried this with two single hosts: iptables -A POSTROUTING -j MASQUERADE -o eth0 -t nat iptables -A POSTROUTING -j MASQUERADE -o wlan0 -t nat echo 200 Forw >>

Hello good day to all ... this is my setup 1 Linux Wireless Access Point, connected are 4 wireless gateway in which i needed to apply shaping ... ok here is the weird part... clients on each gateway download files from the Acess Point ... a 500 mb file through ftp on gateway 1 which is up to 64 kbps ... the result is from 60-64 kbps speed which is fine ... on gateway 2 which is 128 kbps ... the

I know, I know... don't use the non-standard kernels unless you have to... BUT: I have a D-Link N150 USB card. Bus 001 Device 004: ID 0846:9030 NetGear, Inc. WNA1100 Wireless-N 150 [Atheros AR9271] This isn't supported in C5, but it is supported in newer kernels (ath9k_htc). So let's try NDISwrapper: # rpm -i kmod\-ndiswrapper\-1.56\-1.el5.elrepo.i686.rpm

This is a continuation of my previous thread: "Broadcom Wifi Problem" Following a post from "James A. Peltier", who said: You can use the rpmforge version or compile it yourself. I've used this one with success using the details described earlier. http://www.broadcom.com/support/802.11/linux_sta.php I did however have to patch it with

Hi folks I have a CentOS box with 2 network cards. One is eth0 and the other is wlan0 (Linksys WUSB54GC USB wifi card) I use wlan0 to stay linked with other workstations in an small network and eth0 just in case I need to get wired to solve some problem. eth0 is always unpluged while things are going ok. Te problem is everytime my AP is turned off for whatever reason or the link is down, no

I get a message while booting of: ide2: I/O resource 0x3EE-0x3EE not free. ide2: ports already in use, skipping probe Googling for this, I find it is relatively common, and on different laptops. I thought it might be my internal SD reader causing the problems, but these other notebooks do not have such devices. Then I found: http://www.cl.cam.ac.uk/~pb22/I8600/ and: " IrDA -

Hi guys, I have a problem with my Centos 6.4. I am experiencing a Wireless Disconnects, some time ago I had them constantly each 2-3minutes. After upgrading to new kernel (and other software from "Software Update" I am still exepriencing disconnects but every 10-15 minutes. It makes me angry because I am doing a lot of work with ftp servers. Card: *Atheros Communications Inc. AR9285

I just installed an Asus PCE-n13 wireless card into one of my CentOS 5.6 systems. It uses the RaLink 2680 chip set and I was able to get the driver loaded using modprobe rt2x00pci.ko. I saw no error and now see that the module is loaded along with mac80211 and other dependencies. Now I need to know how to create the wlan0 device. I can find nothing via Google searches on how to create that

Opps! After reading the email below I noticed something in ''ifconfig''. The wireless interface is ''wlan0'' not ''wan0''. I modified the wireless interface in /etc/shorewall/interface to wlan0 started shorewall I can connect eo the INTERNET with shorewall running Horace From: Horace Franklin Jr

Hello I've got this Mini-PC https://www.zotac.com/product/mini_pcs/zbox-ci323-nano everything is fine -> latest 6.8 kernel works; both Ethernet-Interfaces work and also the WLAN-Interface works; the two Ethernet-Interfaces are eth0 and eth1 the WLAN-Interface is wlan0 eth1 is connected on ISP side eth0 is connected on my LAN side to a switch; and wlan0 shall also be on my LAN side f?r

Hi, Is anyone here using the "Network Connect" VPN software from Pulse Secure (which was previously known as Juniper Networks Network Connect)? I've used this successfully in the past to connect to the machines at work from home. That was with CentOS 6, though, on CentOS 7 I can't seem to get it to work. The software actually starts, and it also successfully sets up a

Hi there, I've finally had a deeper look and found the Lollipop routing issues root cause: Lollipop uses several routing tables instead of the default one for previous Android versions. The main routing table is used with lowest priority per default: root at hammerhead:/ # ip rule show 0: from all lookup local 10000: from all fwmark 0xc0000/0xd0000 lookup legacy_system 13000: from all