similar to: U32 port matching trouble

Hi Here is a short description of my network: ppp0 (adsl) ppp1 (adsl) | | | | --------------------- | Router | | Firewall | | MASQUERAD | | DNAT | | | | eth0 | --------------------- | | | ---------------------- |

Hello Shorewall list, I''m a happy Shorewall user since a few years now and everything works fine for me except one thing that I try to implement since a week, the multi-isp. I''ve downloaded the 2.4.0 Stable release yesterday and tried the RC2 since a week. My config is a Debian running a kernel 2.4.27 home made with the CONNMARK.diff patch applied I''m using 2 ISP,

I have two adsl lines on my linux firewall box and i want to do some load balance between them...i tried a lot of different things, but it isn´t working...Following the instructions of http://lartc.org/howto/lartc.rpdb.multiple-links.html i used the configuration above. using "iptraf" I can see some few packets using the ppp1 connection, but almost all the packets use ppp0 connection.

I need basic PPPoE startup help. adsl-start DID bring up my PPPoE link (ppp0) to my ISP over eth0 via the DSL modem/bridge. My IPv4 CIDR block is routing and Shorewall is doing the firewalling. But shorewall has to be started after ppp0 is up and working. For now this means running shorewall restart (or start?). Shorewall 4.2 will have a way to restart shorewall without recompiling, I

Hello all, We have two ADSL lines configured on a single box, hence interfaces ppp0 & ppp1. Is there a way to route packets to ppp0, say based on destination port 80 & other traffic like voice through ppp1? Thanks.

That could have gone smoother. I had many problems with the NFS install on my firewall then once I got the server back up, mail delivery was broken :- ( I still haven''t gotten ulogd to run under RH9.0 but everything else seems to be working ok... -Tom -- Tom Eastep \ Shorewall - iptables made easy Shoreline, \ http://www.shorewall.net Washington USA \ teastep@shorewall.net

Hi, I currently connect to my ISP via my adsl modem in bridge mode and PPPoE. I am due to put a second PPPoE ISP onto my firewall box which will give me ppp0 (general) and ppp1 (static leased line). The static leased line will run a number of services on its static IP and it is therefore imperative to make sure rules defined for the static line are assigned to the correct interface. I need this to

i''ve read your http://lartc.org/howto/lartc.rpdb.multiple-links.html article as well as Advanced IP Routing (esp. chapter 10.4) and still unable to make this thing work. am i that helpless? :) is there anyone to guide me through the multiple ISP setup? into details. i got 2 dsl connections from different ISPs (A and B), both connections use PPPoE, both got assigned with dynamic IPs

My Internet gateway is using ADSL PPPoE connection with dynamic public IP assigned by ISP. My Internet gateway is Redhat AS3 U2, shorewall 2.0.9 As my ISP provided 4 simultaneous pppoe dailup connection for the same physical adsl line. My linux server can be configured for multiple pppoe connection i.e. ppp0, ppp1, ppp2, ppp3 Is it possible of shorewall to assigned say ppp0''s IP is

Hi, Thanks for the reply. Thats where the problem starts. If I set ppp0 as the default gw the internet doesnt work anymore. This is how im doing it... route del default route add default gw 217.32.81.74 dev ppp0 if I put it back to ppp1... route del default route add default gw 217.32.68.73 dev ppp1 It works fine again. Whats up with that? Cheers, Chris ----- Original Message

Hi, I''ve set up a Linux box with redhat on to act as an internet gateway and I''m running into a few problems. Its got two adsl modems connected to it, both connected to seperate 512kbs lines. Now I''ve followed the simple source routing in the advanced routing howto to the letter but it doesnt work. I''ve got it autoconnecting on startup and redhat puts ppp1

Hi, I have established two connections to the same ISP. After that ip route list showed this: 195.14.247.94 dev ppp0 proto kernel scope link src 81.173.141.207 195.14.247.94 dev ppp1 proto kernel scope link src 81.173.237.84 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.1 default via 195.14.247.94 dev ppp0 I want 192.168.0.2 to connect to the internet by ppp1 and all

Hi. The task: 1. There 3 servers and a router with 2 PPPoE connections (let call them: ppp0, ppp1). 2. There are several groups of Inet-clients to be served (Servers, Clients and Club). 3. The task is: - to route Club through the ppp1; - to Servers and Clients through ppp0; (Next is reproduced from memory and may be slightly incorrect) router # netstat -nr Kernel IP routing table

Hi ! Recently i switched my internet provider, to get more speed but another braindead setup regarding public ip addresses. I now have 4 PPTP Tunnel available, of which i''m using one as the gateway ip doing masquerading to other machines in my local lan, excluding three other machines, which i would like to use 1:1 nat to get them a direct access to one of the pptp tunnels. I was

how to use iproute/iptables to balance by packet OUTBOUND traffic between 2 PPP (pptp cable modem and pppoe adsl modem) links to the same ISP . also by using the fact that the ISP dosen''t filter source IP address - meaning i can use either PPP''s link assigned IP address as the source IP in the ip header.., it works for both devices.., what i want to achive is : when uploading a

Hello all, I have been doing a lot of archive searching over the last week reading posts on IMQ and it''s apparent stability / instability. I have seen a number of posts about it not being maintained as well. Can anyone talk to me about IMQ''s stability in a heavy throughput environment (20 Mbps) and what was causing IMQ to fail if you know. Thanks, Mike

Hello Lartc Mailing List: Been working on something the last week and a half and ALMOST have it working.., just need a few pointers from the wizards on this mailing list to nail it. Ok, my setup is a hub and spoke arrangement, hub is Cisco 2821 with IOS 12.4. Spokes are ruggencom RX1000 routers, Debian based with the following versions installed: rx1000test:~# uname -a Linux rx1000test

please, help, i have build vpn server (suse 9 + poptop), i have managed to implement tc htb in ip-up script, but every client has own ppp interface (ppp0, ppp1, ppp2...), and my idea is to share available bandwidth, not to limit connection, how to build root tc rule, when I have more then one interface?... please any one width experiance regards _______________________________________________

Hi, can anyone help me with this problem i''ve got! I have a problem with routing on my Mandrake 7.2 Linux Box i was wondering if you could help me with. I live in Australia and as broadband access isn''t very available at the moment, i have 2 modems to dialup to my isp (dynamic ips assigned) to increase my bandwidth at an affordable level. What currently happens is i have a

Hey, I''ve been scouring the web these past few days trying to find a suitable technique to load balance my network. Unfortunately I think my setup is very uncommon, so I''m looking to you guys to see if you can help. I currently have 2 ADSL modems, provided by the same ISP and terminating on the same gateway (I think having the same gateway is what is causing the problems, since