similar to: Terrible problem, some men in my net changed their MACs! :/

Hi Is there a program which allow me to see how "my" traffic goes through my iptables rules? Which accept it, which deny? Right now my router has a little bit of traffic and its hard to see only mine traffic. -- Miłego Dnia Krystian Antoni _______________________________________________ LARTC mailing list LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

I''m looking for a program that will replace the automatic ARP table population by the Linux kernel. The daemon should fix the MAC <-> IP entry from the IP of the first packet with that MAC received. Is there anything like this? -- damjan | дамјан This is my jabber ID --> damjan@bagra.net.mk <-- not my mail address!!! _______________________________________________ LARTC

Hi all, As I read into the forum, NATting (SNAT) is expensive, using iptables to translate IP sucks the performance of the system. I just want to know if IProute2 can handle NATting and if it handels NATting can it performed faster than iptables? thanks, Wennie

Ok, the story is this, I''m running an Unreal Tournament 2004 server. It''s running on a system that has two external NICs that are connected to different ISPs. I would like players to be able to connect to the server from either link. My default gateway goes through NIC1. For traffic through NIC2 to work I simply added an extra routing table and rule. The extra routing table has

Hello, we are using HTB for dividing 15 Mb/s upload rate to 1022 classes (rate 14 kb/s, ceil 15 Mb/s), but sometimes ksoftirqd_CPU0 uses the most of the CPU-time (over 90% CPU load is casual in such situation). This situation occurs several times a week and takes minutes or one hour and during that time it has enormous packet loss. Reboot of the machine usually solves this problem. Because

Hello Everybody, I have configured a Linux box that does traffic shaping. Its working wonderfully fine, just as expected...Now i want to measure the bandwidth consumed by each of my hosts....But I dont want SNMP to run on all the hosts[as required by MRTG] I used iptraf on my linux box, but it only measures the bandwidth on interface basis only.... I tried installing traffic-vis, its not working

Hi, How can I set equal bandwidth of 512kbit downlink and 256kbit uplink for every single IP address of 254 IP addresses I have in my LAN? Regards, ro0ot

Hello, I''m looking how (if) can I solve the following problem using HTB and iproute2: I need to assing the same bandwidth limit to every client, but the problem is that clients will be random - i.e. I know niether number of clients no IP or MAC addresses. If anybody knows FreeBSD''s ipfw2 - I''m looking for something like "ipfw pipe 150 config mask dst-ip 0xffffffff

what is the limit on the arp cache entires ?! Does someone have very big LANs with linux-routers ? How big ? (i mean flat L2 network, not segmented) I want to know how much can my net can scale ? thanx _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Etx1 - First Internet Line - eth0 Ext2 - Second Internet line - eth2 LAN - Local Area Network - eth1 Other traffic - Ext1 -------+-------+--------------- Ext2 ---Web goes Here eth0 | |eth2 +-------+-------+ | ROUTER | +----+------+---+ |eth1 192.168.0.0/24 -----------------+ | 192.168.0.1/24------------------- - Gateway |

Hello there, Can someone please explain why do one neeed IMQ ? I can already shape incoming traffic on my nat router by creating qdiscs on LAN-side interface. I have done some tests, whith simple bandwidth limmiting, and it works. I''ve read just about all the stuff on www.linuximq.net ... but couldn''t make myself an ideea on why would someone need IMQ for ingress policing ...

Hi, A majority of our work inolves ftp to my clients'' side over our slow connection. Now we need to allocate a greater b/w for this protocol. Is there anyway I can do it using lartc easily? Any suggestions on this please? With warm regards, -Payal _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc

We have a Linux box that is acting as the gateway to the internet for about 400 people, typically there are not more then 50 of them using the internet at any given time. We would like to provide different levels of access to different users. For example 128kbps to some users and 256kbps to others. We have considered creating a class and qdisc for each user (using htb) however we don''t

Hello, I have a problem with the latency of the packets passing a Linux router, and I thought perhaps you could put some light on it. It''s quite simple. I have one ADSL connection, and a LAN. The gateway is the Linux machine or a Windows XP machine. When the wXP is routing, for a host inside the LAN, the latency of, for example, the Counter Strike game to a given server is around 20 to 30

Hi guys, Can you take a look at this? :) +-----------+ | | eth1-|- | | -|-eth0---LAN--- | | eth2-|- | | | +-----------+ - eth0 is connected to the LAN having the IP=LAN_IP eth1 is connected to the first ISP having IP=ISP_IP_1 and GW=ISP_GW_1 eth2 is connected to the second ISP having IP=ISP_IP_2 and GW=ISP_GW_2 I need

What''s wrong... I have Celeron 633MHz nd 768Mb RAM. When I''m running my script everything is OK, but when I''m connecting Internet and LAN link computer is hanging. But when i dissconnect this everything is OK. I have 500 users, 1500 classes and 3000 filters. Is it normal? What should I do?

Hi all, I need to provide shell hosting for about 40 users, and few days ago I found the wondershaper script, so Im trying to know if this script could help me to improve interactive ssh/telnet connections. Wondershaper could help me or its only efective on OUTGOINGS requests? Ok, any comment and feedback will be welcome. Sorry for my bad english and THANKS in advance.

Using a default xen3.0.1 setup for dom0(rhel4 distro) and domUs (gentoo, rhel4, centos4.2 distros, ttylinux) with the domUs all having dhcp turned on, is there an easy way to tell from within the dom0 what ip addresses were assigned to the domUs after bootup? Toby Ford USi _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com

On Fri, May 8, 2009 at 10:14 AM, Javier Barroso <javibarroso@gmail.com> wrote: > Hello, > > I have a etch xen server with a virtual machine with 2 network > interfaces configured. Every interface has a different mac, and inside > the host has a different ip. > > However I can see with tcpdump and arpwatch (I discover this because > arpwatch told me), about the two ips

Hi, I''ve a local LAN consisting of about 150 machines. I''m using a Linux machine as the gateway machine which inturn connects to two different ISPs. My question is can a Linux based machine match the performance of a hardware based routers provided by Cisco,... OR is my decision to go for a Linux based solution is a wrong one?. Is there so much difference between these